Content |
D4510_MANUAL_GB_V1.pdf
• Soft start technology • Advanced protection circuits • SMPS & Class-D Amp Technology
The DAP-Audio CA-series Compact Amplifiers are exactly that! A very compact housed power amplifier with all the necessary features for the contemporary users. Within the family of 4 there are two straight forward 2-channel models of different amplifier power, one 3-channel model which has an included crossover to easily setup a 3.1 configuration, and one 4-channel model which also includes a crossover.
Specifications
Output Power Stereo 2Ohm: Not recommended Stereo 4Ohm: 2x 150 Watt RMS Stereo 8Ohm: 2x 90 Watt RMS Bridge 2Ohm: Not Allowed Bridge 4Ohm: 1x 275 Watt RMS Bridge 8Ohm: 1x 190 Watt RMS Frequency Response: 20Hz - 20KHz, +0/-1dB THD: 96 dB A-weighted Crosstalk: >70dB Damping Factor: >180 Gain: 28V Input Sensitivity: 0,9-1,1V (+/-1dBv) Input Impedance: 20kOhm balanced, 10kOhm unbalanced Output Mode: Stereo / Bridged Amp Technology: Class D Power Supply: SMPS Protection: Clip Limiter (Fixed) Short Circuit Overheat Overload DC Voltage Soft Start Cooling: Forced-air by axial fan Airflow: Front to side Input Connectors: 3-pin XLR, TRS 6,3mm Jack Output Connectors: Speakon, TRS 6,3mm Jack Power Connector: IEC Input Voltage: 210~240VAC… 50/60Hz Power Consumption: 450W Dimensions: 484x281x44mm Installation depth: 278mm (excl. conn.) Weight: 3,7Kg |
Reference Quality Power Amplifier [R-300 Plus] - Controls :
Front : Power on/off switch, attenuator, LED indicator
Rear : Mode seletor switch, Stereo/bridged mono switch - Connectors :
Input : 1 XLR, 1/4" balanced per channel
Output : 5-way binding post and SpeakonTM per channel - Indicators :
Power : Green, Protection : Red, Clip : Red, Signal : Green - Power Source : 100-120VAC or 220-240VAC; 50/60Hz
(supplied AC mains transformer depends on country requirements) - Power Consumption : 250W(2.4A)
- Weight : 8.4kg/18.5lb
- Dimensions (WxHxD) : 482x88x317mm/19x3.5x12.5in
|
- Output Power:
500W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
330W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
- Bridge Mode, Mono 820W RMS @ 8 Ohms, 1K Hz, 1% THD
- Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
- Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
- Slew Rate: 15V Per usec
- Damping Factor: @ 8 Ohm: 300
- Impedance: 20 Ohms balanced / 10 Ohms unbalanced
- Cooling System: 2 individual fans
- Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift; Limiter
- build in clip limiter
- Input: XLR 3pin + Jack 6,3mm
- output: Speakon + Binding post
- Dimensions (LxWxH): 360 x 482 x 88mm 2-rack mount spaces
- Weight: 15 KG.
|
- 2Χ350W 8Ω 2x500W 4Ω 2x650W STEREO MODE
- BRIDGE 2000W 4 Ω
- 16Kg
- 2 x 1,000 Watts into 2 Ohms; 2 x 750 Watts into 4 Ohms; 2,000 Watts into 4 Ohms (bridge mode)
- Precise Power, Signal and Clip LEDs to monitor performance
- XLR and 1/4" TRS input connectors for compatibility with any source
- Professional speaker connectors and "touch-proof” binding posts support most speaker wiring systems
- Selectable low-frequency filters (30 Hz or 50 Hz) remove distracting infra-sound frequencies
- Independent limiters per channel offer reliable protection against overload and distortion
- High-current toroidal transformer for ultra-high transient response and absolute reliability
- Ultra-reliable Toshiba/Fairchild power transistors
- Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
- “Back-to-front” ventilation system including air filter for reliable operation
- “Built-like-a-tank,” impact-resistant, all-steel 2U rackmount chassis
- High-quality components and exceptionally rugged construction ensure long life
- Conceived and designed by BEHRINGER Germany
|
The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The amplifier provides 2x300W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 4Ω: | 2 x 300 Watt rms | | Power output stereo 8Ω: | 2 x 180 Watt rms | | Power output bridged 8Ω: | 600 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | > 105 dB | | Crosstalk: | > 70 dB | | Distortion (THD+N): | | | Intermodulation: | | | Damping factor: | 200:1 (8 Ω) | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | Input impedance: | 10.000 kΩ | | Controls: | Volume control for each channel | |
OUTPUT SECTION |
---|
Output connector: | 2 x Neutrik Speakon 4 ways | |
SYSTEM PARAMETERS |
---|
Cooling: | Two-speed fan | | Protections: | Temperature, DC, RFI short circuit, Soft-Start thermal on transformer | | Amplifier class: | H | |
POWER REQUIREMENT |
---|
Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | Max.current: | 6 A | | Power Consumption: | 1300 W | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 88 / 3.46 mm/inch | | Width: | 483 / 19.01 mm/inch | | Depth: | 350 / 13.77 mm/inch | | Net Weight: | 11.45 / 25.24 Kg/Lbs | |
SHIPPING INFORMATION |
---|
Package height: | 120 / 4.72 mm/inch | | Package width: | 540 / 21.25 mm/inch | | Package depth: | 470 / 18.05 mm/inch | | Shipping Weight: | 13.81 / 30.44 Kg/Lbs |
|
XB Series - Intelligent Power
Power Without Compromises. The XB is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection- the XB is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX / Speakon LED Indicators for POWER, SIGNAL, CLIP, PROTECT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XB 800: 2x 400 W @ 4 Ohm Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.025% Signal-to-Noise Ratio: < 103 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: 500 @ 4 Ohm Cooling: 2x fan (temp. reg. variable speed) Weight: 13 kg/(29 lbs) Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)
|
Reviews
There are no reviews yet.