DAP AUDIO D4510 CA-2150 2Channel 2x150W 4Ω Amplifier

D4510_MANUAL_GB_V1.pdf

• Soft start technology
• Advanced protection circuits
• SMPS & Class-D Amp Technology

The DAP-Audio CA-series Compact Amplifiers are exactly that! A very compact housed power amplifier with all the necessary features for the contemporary users. Within the family of 4 there are two straight forward 2-channel models of different amplifier power, one 3-channel model which has an included crossover to easily setup a 3.1 configuration,  and one 4-channel model which also includes a crossover.

Output Power
Stereo 2Ohm: Not recommended
Stereo 4Ohm: 2x 150 Watt RMS
Stereo 8Ohm: 2x 90 Watt RMS
Bridge 2Ohm: Not Allowed
Bridge 4Ohm: 1x 275 Watt RMS
Bridge 8Ohm: 1x 190 Watt RMS
Frequency Response: 20Hz - 20KHz, +0/-1dB
THD: 96 dB A-weighted
Crosstalk: >70dB
Damping Factor: >180
Gain: 28V
Input Sensitivity: 0,9-1,1V (+/-1dBv)
Input Impedance: 20kOhm balanced, 10kOhm unbalanced
Output Mode: Stereo / Bridged
Amp Technology: Class D
Power Supply: SMPS
Protection: Clip Limiter (Fixed)
Short Circuit
Overheat
Overload
DC Voltage
Soft Start
Cooling: Forced-air by axial fan
Airflow: Front to side
Input Connectors: 3-pin XLR, TRS 6,3mm Jack
Output Connectors: Speakon, TRS 6,3mm Jack
Power Connector: IEC
Input Voltage: 210~240VAC… 50/60Hz
Power Consumption: 450W
Dimensions: 484x281x44mm
Installation depth: 278mm (excl. conn.)
Weight: 3,7Kg

Reference Quality Power Amplifier [R-300 Plus]

• Controls :
  Front : Power on/off switch, attenuator, LED indicator
  Rear : Mode seletor switch, Stereo/bridged mono switch
• Connectors :
  Input : 1 XLR, 1/4" balanced per channel
  Output : 5-way binding post and SpeakonTM per channel
• Indicators :
  Power : Green, Protection : Red, Clip : Red, Signal : Green
• Power Source : 100-120VAC or 220-240VAC; 50/60Hz
  (supplied AC mains transformer depends on country requirements)
• Power Consumption : 250W(2.4A)
• Weight : 8.4kg/18.5lb
• Dimensions (WxHxD) : 482x88x317mm/19x3.5x12.5in

- Output Power:
500W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
330W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
- Bridge Mode, Mono 820W RMS @ 8 Ohms, 1K Hz, 1% THD
- Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
- Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
- Slew Rate: 15V Per usec
- Damping Factor: @ 8 Ohm: 300
- Impedance: 20 Ohms balanced / 10 Ohms unbalanced
- Cooling System: 2 individual fans
- Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift; Limiter
- build in clip limiter
- Input: XLR 3pin + Jack 6,3mm
- output: Speakon + Binding post
- Dimensions (LxWxH): 360 x 482 x 88mm 2-rack mount spaces
- Weight: 15 KG.

• 2Χ350W 8Ω 2x500W 4Ω 2x650W  STEREO MODE
  
  
  
• BRIDGE 2000W 4 Ω
• 16Kg

• 2 x 1,000 Watts into 2 Ohms; 2 x 750 Watts into 4 Ohms; 2,000 Watts into 4 Ohms (bridge mode)
• Precise Power, Signal and Clip LEDs to monitor performance
• XLR and 1/4" TRS input connectors for compatibility with any source
• Professional speaker connectors and "touch-proof” binding posts support most speaker wiring systems
• Selectable low-frequency filters (30 Hz or 50 Hz) remove distracting infra-sound frequencies
• Independent limiters per channel offer reliable protection against overload and distortion
• High-current toroidal transformer for ultra-high transient response and absolute reliability
• Ultra-reliable Toshiba/Fairchild power transistors
• Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers without shutting down the show
• “Back-to-front” ventilation system including air filter for reliable operation
• “Built-like-a-tank,” impact-resistant, all-steel 2U rackmount chassis
• High-quality components and exceptionally rugged construction ensure long life
• Conceived and designed by BEHRINGER Germany

The high efficiency of the ED series enables maximum efficiency with low heat generation.

A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The amplifier provides 2x300W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.

XB Series - Intelligent Power

Power Without Compromises.
The XB is designed for paging, music and alarm signals. Versatile, dynamic
and extremely rugged according to IEC286-3. For the highest requirements
in safety and quality.
Sequential power on, alive contacts and incorporated ground fault detection-
the XB is the solution under all conditions. Without the need for additional
equipment. For uninterrupted and troublefree operation.

High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter,
3 ms Muting Delay
PHOENIX / Speakon
LED Indicators for POWER, SIGNAL, CLIP, PROTECT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty

TECHNICAL DATA:
XB 800:  2x 400 W @ 4 Ohm
Class:  AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD:  < 0.025%
Signal-to-Noise Ratio:  < 103 dB
Channel Seperation:  > 85 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Damping Factor:  500 @ 4 Ohm
Cooling:  2x fan (temp. reg. variable speed)
Weight: 13 kg/(29 lbs)                                 
Dimensions:  2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)