The Qi-amplifier range is developed for installation use to create a perfect match with the Xi installation speaker range. Due to the rugged steel housing it can also be applied for mobile use. With only 1U it gives power for 4 channels. All 4 channels are individual controllable and bridge mode can be set for […]
The Qi-amplifier range is developed for installation use to create a perfect match with the Xi installation speaker range. Due to the rugged steel housing it can also be applied for mobile use. With only 1U it gives power for 4 channels. All 4 channels are individual controllable and bridge mode can be set for each stereo pair. With the SMPS and Class-D amplification it is a light weight solution with a high efficiency power consumption / power output ratio. An advanced protection circuit will protect the amplifier and it’s connected speakers. It has a short circuit/ thermal, DC ,RF protection and a soft start system. The Qi-amplifiers are made with high-quality low deviation components to ensure a perfect sound quality and a long life time.
The Qi-amplifier range is developed for installation use to create a perfect match with the Xi installation speaker range. Due to the rugged steel housing it can also be applied for mobile use. With only 1U it gives power for 4 channels. All 4 channels are individual controllable and bridge mode can be set for each stereo pair. With the SMPS and Class-D amplification it is a light weight solution with a high efficiency power consumption / power output ratio. An advanced protection circuit will protect the amplifier and it's connected speakers. It has a short circuit/ thermal, DC ,RF protection and a soft start system. The Qi-amplifiers are made with high-quality low deviation components to ensure a perfect sound quality and a long life time.
Specifications
Output power
Stereo 4Ohm: 4x 200W
Stereo 8Ohm: 4x 120W
Bridge 8Ohm: 2x 400W
Parameters
S/N Ratio: >90dB
Input sensitivity: 0,65V
Input impedance: 20kOhm Bal./10Kohm unbal.
Technology: Class-D
Protection: short circuit, DC, RF, Soft start
Cooling: Temp controlled fan
Power supply: SMPS
Connections
Input: 4x XLR
Output: 4x Speaker connector
Power: IEC
Physical
Dimensions: 388 x 435 x 44 (WxHxD)
Installation depth: 370 (excl. conn.)
Weight: 5.8Kg
Electrical
Input Voltage: 100~240VAC...50/60Hz
Power consumption: 500W
Multichannel Power with Minimum FootprintThe T Series multichannel power amplifiers have been designed especially for installation and networked audio systems.
T Series amplifiers* are available with 4 and 8 discrete channels and output ratings from 160 to 320 Watts per channel providing optimum solutions for multizoning. They feature Euroblock inputs, terminal strip outputs and a rugged 2U rackmountable chassis with 4 mm front panel.
*Also available as GPIO versions with remote and emergency paging switchin
Main Features
8 and 4-channel models with 300 and 150 Watts (RMS) output power per channel
compact 2U rackmountable chassis, 220 mm deep, weight 6 kg only
GPIO versions for remote and emergency paging switching
FCM system
oversized heat dissipation system for maximum thermal stability
low THD and high S/N ratio
all channels bridgeable in pairs
switchable input gain (26, 32 and 38 dB)
subsonic filters for each channel (35 Hz)
intelligent, quiet fan cooling system
terminal strip loudspeaker connectors
PCBs with surface-mount technology (SMT) for increased reliability
protection, signal, clip, power on and standby LED indicators for each channel
compact QuantaPulse power supply
multi-voltage: automatic voltage converter for worldwide use, no switching required
protections: soft start, turn on/turn off muting, thermal overload, DC, RF, short circuit, open circuit, load mismatch and power supply overload
ICL™: improved Intelligent Clip Limiting prevents loudspeaker damage while maintaining audio quality and punch under clipping conditions.
FCM™: the Faulty Channel Management system prevents overall amplifier shutdown.
GPIO:General-Purpose-I/O-Port
QuantaPulse™ Technology: The Soft Switching Resonant QuantaPulse Power Supply is designed to provide plenty of power when needed monitoring the necessary parameters of voltage and current for a controlled performance at all times. Bi-directional data flow between the power supply and power amp module. Two very important characteristics of the QuantaPulse power supply are the optimization against over-voltages and superior reliability.
• Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less power devices attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™ SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™
• Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal
noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less
power device attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™
SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding
conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis
OUTPUT POWER
T-604
T-1204
T-1208
T-2408
RMS, 1kHz, 1.0% THD+N
4 ohms
4x 160 W
4x 320 W
8x 150 W
8x 300 W
8 ohms
4x 115 W
4x 220 W
8x 100 W
8x 195 W
Bridge @ 8ohms
2x 320 W
2x 640 W
4x 300 W
4x 600 W
Pink Noise 12dB CF
4 ohms
4x 210 W
4x 415 W
8x 180 W
8x 370 W
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™
This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Cookie settingsACCEPT
Privacy & Cookies Policy
Πολιτική χρήσης
Αυτός ο ιστότοπος χρησιμοποιεί cookies για να βελτιώσει την εμπειρία σας ενώ περιηγείστε στον ιστότοπο. Από αυτά τα cookies, κάποια cookie κατηγοριοποιούνται ως απαραίτητα να αποθηκεύονται στο πρόγραμμα περιήγησης σας, καθώς είναι απαραίτητα για τη λειτουργία βασικών λειτουργιών του ιστότοπου. Χρησιμοποιούμε επίσης cookies τρίτων που μας βοηθούν να αναλύσουμε και να κατανοήσουμε πώς χρησιμοποιείτε αυτόν τον ιστότοπο. Αυτά τα cookies θα αποθηκευτούν στο πρόγραμμα περιήγησης σας μόνο με τη συγκατάθεσή σας. Έχετε επίσης την επιλογή να εξαιρεθείτε από αυτά τα cookies. Ωστόσο, η εξαίρεση από ορισμένα από αυτά τα cookie μπορεί να επηρεάσει την εμπειρία περιήγησης σας.
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.
Any cookies that may not be particularly necessary for the website to function and is used specifically to collect user personal data via analytics, ads, other embedded contents are termed as non-necessary cookies. It is mandatory to procure user consent prior to running these cookies on your website.
 80W <br>
4ohm (Quad Ch) 120W <br>
8ohm bridged mono 240W
</p>
<p>
Input Sensitivity (8ohm, 1kHz) 0.775Vrms <br>
Input Impedance 20kohm Balanced <br>
Slew Rate (8ohm, Full Swing) ±30V/?sec <br>
Frequency Response (±0.5dB) 20kHz ~ 50kHz <br>
T.H.D. (f=20Hz~20kHz, Half Power) 0.03% <br>
Signal to Noise Ratio 105dB <br>
Damping Factor (8ohm, 1kHz) 100 <br>
Rasidual Noise -85dB <br>
Channel Separation (8ohm, 1kHz) 80dB <br>
Voltage Gain (4ohm) 26dB 29dB 32dB <br>
Power Source 100-120VAC or 220-240VAC ; 50/60Hz<br>
(supplied AC mains transformer depends on country requirements) <br>
Power Consumption 300W 420W 770W <br>
Weight 11.5kg/25.3lb 15.5kg/34.2lb 17kg/37.5lb <br>
Dimensions 482(W) x 88(H) x 369(D) mm<br>
/19(W) x 3.5(H) x 14.5(D) in <br>
<br>
</p></td><td><h2 class= "aposirsi_electrovoice")
PA Power Amplifier 4 x 160 W 4 Ohms
Reviews
There are no reviews yet.