Content | The Qi-amplifier range is developed for installation use to create a perfect match with the Xi installation speaker range. Due to the rugged steel housing it can also be applied for mobile use. With only 1U it gives power for 4 channels. All 4 channels are individual controllable and bridge mode can be set for each stereo pair. With the SMPS and Class-D amplification it is a light weight solution with a high efficiency power consumption / power output ratio. An advanced protection circuit will protect the amplifier and it\'s connected speakers. It has a short circuit/ thermal, DC ,RF protection and a soft start system. The Qi-amplifiers are made with high-quality low deviation components to ensure a perfect sound quality and a long life time.
Specifications
Output power
Stereo 4Ohm: 4x 400W
Stereo 8Ohm: 4x 250W
Bridge 8Ohm: 2x 800W
Parameters
S/N Ratio: >90dB
Input sensitivity: 0,7V
Input impedance: 20kOhm Bal./10Kohm unbal.
Technology: Class-D
Protection: short circuit, DC, RF, Soft start
Cooling: Temp controlled fan
Power supply: SMPS
Connections
Input: 4x XLR
Output: 4x Speaker connector
Power: IEC
Physical
Dimensions: 388 x 435 x 44 (WxHxD)
Installation depth: 370 (excl. conn.)
Weight: 5.8Kg
Electrical
Input Voltage: 100~240VAC...50/60Hz
Power consumption: 875W |
Electro Voice PA 4150L features: * 100 Watts / 8 Ohms * 160 Watts / 4 Ohms * The amplifier channels can be bridged for more flexibility * Frequency response (-1dB): 10 Hz - 40 kHz * Signal-to-Noise Ratio: 100 dB * Provides excellent headroom for a wide dynamic range on music signals * Protection: audio limiters, high temperature, peak current limiters, turn-on delay * Marked level controls on the rear panel provide hidden reliable level adjustments for each channel * Front panel LEDs indicate signal present, 0 dB, and limit * Phoenix type connectors for inputs and outputs provide an easy rack wiring * Cooling: front-to-rear * Power requirements: 120V or 230V, 50 Hz - 60 Hz * Dimensions (WxHxD): 483 x 88 x 406 mm / 19" x 3.5" x 16" * Weight: 18 kg / 39.65 lbs
|
Power Output Level 20Hz - 20kHz 1kHz THD+N=0.2%, 8Ω 80W x 4
Power Output Level 20Hz - 20kHz 1kHz THD+N=0.2%, 4Ω 115W x 4
Sensitivity, RL=8. Att.max +4dB
S/N Ratio, 20Hz-20kHz (DIN AUDIO) 100dB
Idle Power Consumption 40W
1/8 Power Consumption (4Ω) 500W
Power Bandwidth, (Half power THD+N=0.5%) 10Hz – 40kHz
Intermodulation Distortion, 60Hz: 7kHz, 4:1, half power 0.1%
Frequency Response, f=20Hz-20kHz -0.5dB, 0dB, 0dB
Residual Noise, 20Hz-20kHz(DIN AUDIO) -70dB
Voltage Gain, 8Ω, f=1kHz 100
Sensitivity, ATT. max 26dB
Maximum Input Voltage 22dB
Input Impedance 30kΩ (balance) 15kΩ (unbalance)
Controls, Front panel POWER switch (push on/push off), attenuator (31position) x 4
Controls, Rear panel MODE switch (STEREO/BRIDGE/PARALLEL) x 2 HPF switch (OFF/20Hz/55Hz 12dB/oct) x 2
Connectors, Output 5–way binding post/ch
Connectors, DATA PORT D-sub15P, Monitor:Output Level/ch,Active/ch, Model Detect Control:Mute/ch
Connectors, Power AC inlet x 1
Indicators, POWER x 1 (Green)
Indicators, SIGNAL x 4(Green)
Indicators, CLIP/LIMIT x 4 (Red)
Indicators, PROTECT/MUTE x 4 (Red)
Load Protection POWER switch on/off mute, DC-fault output relay off
Power Requirements UC: 120V / 60Hz,
Weight 10kg (22 lbs.)
Dimensions (W x H x D) 480 x 88 x 412.2 mm (18-7/8" x 3-7/16" x 16-1/4“)
|
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
|
Amplifier Gain 32 dB (Lo-Z), 33 dB (70V), 36 dB (100V) Analog Inputs 4, electronically balanced, Phoenix-type Audio Network No CAN Bus Interface Yes (With Optional RCM-810 Card) Continuous Rated Power (1 kHz, THD 1%) 100v 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 2Ω 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 4Ω 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 70v 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 8Ω 500 Watts Continuous Rated Power (20-20 kHz, THD Continuous Rated Power (20-20 kHz, THD Continuous Rated Power (20-20 kHz, THD Continuous Rated Power (20-20 kHz, THD Cooling Front-to-Rear, continuously variable fans DIM 30 0.02 % Electronics Type Amplifier Frequency Response 15 Hz-30 kHz Input Impedance (Balanced) 20 kΩ Input Sensitivity 0 dBu (.775V)-2 Ω, +3 dBu (1.1V)-4/8 Ω, +6 dBu (1.55) 70V/100V Intermodulation Distortion (SMPTE) 0.05 % Mains Voltage 220 - 240 V, 50 - 60 Hz or 120 V, 50 - 60 Hz, 50 - 60 Hz Network Control (IRIS-Net) Optional Total Harmonic Distortion 0.05 % Variable Load Drive (VLD) Yes Height 2RU 88.1 mm (3.47“) Width 483 mm (19.02“) Depth 421.5 mm (16.59“) Weight Net 11.1 kg (24.47 lbs)
|
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
|
Reviews
There are no reviews yet.