M-AUDIO Pulsar II – Small-Diaphragm Studio Condenser Microphone Matched Pair

151.21 incl. GR VAT

In stock

EAN: N/A
Installments calculation
CompareAdd to wishlist Submit Better Price
Carefully selected for their nearly identical response, matched pairs of Pulsar II microphones from M-Audio® deliver superior stereo performance. The brass bodies are equipped with internal shockmounts and low-noise transformerless electronics. Each microphone offers a switchable 10 dB attenuation pad, plus an 80 Hz low-cut filter. Together, these functions allow the Pulsar II microphones to […]

 

Read more

Carefully selected for their nearly identical response, matched pairs of Pulsar II microphones from M-Audio® deliver superior stereo performance. The brass bodies are equipped with internal shockmounts and low-noise transformerless electronics. Each microphone offers a switchable 10 dB attenuation pad, plus an 80 Hz low-cut filter. Together, these functions allow the Pulsar II microphones to adapt to a variety of applications. The included hardware package allows Pulsar II microphones to be mounted in either an X-Y or ORTF (110º) stereo configuration. While ideal for stereo use, these microphones can also be used independently in a wide range of critical recording situations. This complete package includes a stereo mounting bar, hard mounts, risers, windscreens, and cloth bags, as well as a handsome and functional wooden storage/travel case.
Full Features

Two response-matched M-Audio Pulsar II microphones
0.75″ diameter, 6-micron sputtered gold diaphragms
Cardioid pickup patterns
Class A FET transformerless electronics
Brass bodies with internal shockmounts
Switchable 10 dB pads and 80 Hz filters (18 dB/octave)
48 Volt phantom power required
Includes stereo bar, hard mounts, risers, wind screens, and soft bags-all in a wooden travel case

Specifications

Type: Large diaphragm condenser, gold evaporated
Polar pattern: Cardioid
Frequency response: 20 Hz-20 kHz
Sensitivity: 13.8 mV/Pa (-37dBV)
Max. SPL (
Weight 3.00 kg

Reviews

There are no reviews yet.

Be the first to review “M-AUDIO Pulsar II – Small-Diaphragm Studio Condenser Microphone Matched Pair”

Your email address will not be published. Required fields are marked *

Quick Comparison

M-AUDIO Pulsar II - Small-Diaphragm Studio Condenser Microphone Matched Pair removeNEUMANN TLM-103 Condenser studio microphone removeNEUMANN TLM-49 Condenser studio mic removeNEUMANN M-147 TUBE Condenser Cardiodic Microphone removeBEHRINGER B-5 Sputtered Diaphragm Studio Condenser Microphone removeRODE NT-2A Multipattern Condenser Microphone remove
NameM-AUDIO Pulsar II - Small-Diaphragm Studio Condenser Microphone Matched Pair removeNEUMANN TLM-103 Condenser studio microphone removeNEUMANN TLM-49 Condenser studio mic removeNEUMANN M-147 TUBE Condenser Cardiodic Microphone removeBEHRINGER B-5 Sputtered Diaphragm Studio Condenser Microphone removeRODE NT-2A Multipattern Condenser Microphone remove
Image
SKUPulsar II Matched PairH11NE00039H11NE00032H11NE00019E005243H11RD00030
Rating
Price 151.21 incl. GR VAT 1,169.00 incl. GR VAT 1,499.00 incl. GR VAT 2,959.00 incl. GR VAT 80.00 incl. GR VAT 339.00 incl. GR VAT
Stock

In stock

In stock

In stock

Available on backorder

Available on backorder

In stock

AvailabilityIn stockIn stockIn stockAvailable on backorderAvailable on backorderIn stock
Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
Content

Carefully selected for their nearly identical response, matched pairs of Pulsar II microphones from M-Audio® deliver superior stereo performance. The brass bodies are equipped with internal shockmounts and low-noise transformerless electronics. Each microphone offers a switchable 10 dB attenuation pad, plus an 80 Hz low-cut filter. Together, these functions allow the Pulsar II microphones to adapt to a variety of applications. The included hardware package allows Pulsar II microphones to be mounted in either an X-Y or ORTF (110º) stereo configuration. While ideal for stereo use, these microphones can also be used independently in a wide range of critical recording situations. This complete package includes a stereo mounting bar, hard mounts, risers, windscreens, and cloth bags, as well as a handsome and functional wooden storage/travel case.
Full Features

Two response-matched M-Audio Pulsar II microphones
0.75" diameter, 6-micron sputtered gold diaphragms
Cardioid pickup patterns
Class A FET transformerless electronics
Brass bodies with internal shockmounts
Switchable 10 dB pads and 80 Hz filters (18 dB/octave)
48 Volt phantom power required
Includes stereo bar, hard mounts, risers, wind screens, and soft bags-all in a wooden travel case

Specifications
Type:Large diaphragm condenser, gold evaporated
Polar pattern:Cardioid
Frequency response:20 Hz-20 kHz
Sensitivity:13.8 mV/Pa (-37dBV)
Max. SPL (
Large diaphragm cardioid microphone
Pressure gradient transducer with with one-diaphragm capsule
Transformerless circuitry
Extremely low noise: 7 dB-A
Includes swivel mount
Straightforward handling for homerecording and professional studios

High-quality professional equipment for limited budgets

Acoustical operating principle Pressure gradient transducer
Directional pattern Cardioid
Frequency range 20 Hz ... 20 kHz
Sensitivity at 1 kHz into 1 kohm 23 mV/Pa
Rated impedance 50 ohms
Rated load impedance 1 kohms
Equivalent noise level, CCIR1) 17.5 dB
Equivalent noise level, A-weighted1) 7 dB-A
Signal-to-noise ratio, CCIR1) (rel. 94 dB SPL) 76.5 dB
Signal-to-noise ratio, A-weighted1) (rel. 94 dB SPL) 87 dB
Maximum SPL for THD 0.5%2) 138 dB
Maximum output voltage 13 dBu
Dynamic range of the microphone amplifier (A-weighted) 131 dB
Supply voltage (P48, IEC 61938) 48 V ± 4 V
Current consumption (P48, IEC 61938) 3 mA
Matching connector XLR3F
Weight approx. 450 g
Diameter 60 mm
Length 132 mm

 

Acoustical operating principlePressure gradient transducer
Directional patternCardioid
Frequency range20 Hz ... 20 kHz
Sensitivity at 1 kHz into 1 kohm13 mV/Pa
Rated impedance50 ohms
Rated load impedance1000 ohms
Equivalent noise level, CCIR1)23 dB
Equivalent noise level, A-weighted1)12 dB-A
Signal-to-noise ratio, CCIR1) (rel. 94 dB SPL)71 dB
Signal-to-noise ratio, A-weighted1) (rel. 94 dB SPL)82 dB
Maximum SPL for THD 110 dB
Maximum SPL for THD 129 dB
Maximum output voltage for THD -1 dBu
Dyn. range of the mic. amplifier /A-weighted, 0.5 %2))98 dB
Dyn. range of the mic. amplifier /A-weighted, 5 %2))117 dB
Supply voltage (P48, IEC 61938)48 V ± 4 V
Current consumption (P48, IEC 61938)3.2 mA
Matching connectorXLR 3F
Weight825 g
Diameter78 mm
Length165 mm
1) According to IEC 60268-1; CCIR-weighting according to CCIR 468-3, quasi peak; A-weighting according to IEC 61672-1, RMS
2) Measured as equivalent el. input signal

Acoustical operating principlePressure gradient transducer
Directional patternCardioid
Frequency range20 Hz ... 20 kHz
Sensitivity at 1 kHz into 1 kohm20 mV/Pa
Rated impedance50 ohms
Rated load impedance1000 ohms
Equivalent SPL CCIR 468-324 dB
Equivalent SPL DIN/IEC 65112 dB-A
S/N ratio CCIR 468-370 dB
S/N ratio DIN/IEC 65182 dB
Maximum SPL114 dB for THD
Maximum output voltage8 dBu
Dyn. range of the mic. amplifier DIN/IEC 651102 dB for THD
Supply voltagePower supply N 149 A
Matching connectorMicrophone: DIN 8F, Power Supply: XLR 3F
Weight460 g
Diameter57 mm
Length142 mm

Behringer B-5 Sputtered Diaphragm Studio Condenser Microphone



The B-5 is a professional gold-sputtered diaphragm condenser microphone featuring two interchangeable capsules for different pickup patterns (cardioid and omnidirectional). It is perfect for acoustic instruments, vocals and overhead miking. Its ultra low-noise transformerless FET input eliminates low frequency distortion. The -10 dB attenuator can be used with high volume signal sources, while the low-cut filter eliminates floor rumble. The microphone is delivered in a rugged hard case with stand adapter and windscreen.

 

Professional true condenser microphone for studio and live applications
2 interchangeable capsules with cardioid and omnidirectional pickup patterns
Low-mass gold sputtered diaphragm for ultimate sound reproduction
Perfect for acoustic instruments, voice and overhead etc.
Ultra low-noise transformerless FET input eliminates low-frequency distortion
Smooth, super-wide frequency response and incredible musicality
Switchable low-frequency roll-off and -10 dB input attenuation
Gold-plated 3-pin XLR output connector
Rugged construction with satin nickel-plated brass body
Custom microphone stand adapter, windscreen and transport case included

 

 

 

Manual Download

NT2-A - ?The Legend Continues? Multi Pattern 1? Condenser Microphone.
 
The new NT2-A carries on the tradition forged by the now legendary R?DE NT2.
A professional large capsule (1?) studio microphone incorporating three-position
pick-up patterns, pad and high pass filter switches conveniently located on the
mic body.
At the heart of the NT2-A is the Australian designed and manufactured HF1 dual
diaphragm capsule. The frequency and transient response of this new transducer
has been voiced to complement today?s modern recording techniques, and yet still
evoke the silky smooth character of the legendary microphones of the 50?s and 60?s.
These features provide the flexibility and superlative audio characteristics that make
the NT2-A one of the most versatile condenser mics available.
The NT2-A?s variable controls allow switching between Omni, Figure 8, and Cardioid
polar patterns. The three position high-pass filter provides a flat response or an 80Hz
and 40Hz high pass filter to be selected. Finally the microphones Pad can be switched
between 0 dB, -5dB and -10dB. The NT2-A comes in a soft pouch with an M2 stand mount.
 
SPECIFICATIONS:
Features:
The Australian designed and manufactured HF1 1? edge terminated, gold sputtered, dual
5 um diaphragm capsule. 3-position variable polar pattern: Omni, Cardioid & Figure 8; all
controlled on the mic. 3-position variable high-pass filter: Flat, 80 Hz or 40 Hz. 3-position
variable pad: 0 dB, -5 dB or -10 dB. Ultra low noise, transformerless SMT circuitry. Wide
dynamic range. High strength heat-treated steel mesh head. Durable satin nickel finish.
Internal capsule shock mounting. Supplied complete with soft pouch and clip. Designed
and manufactured in Sydney, Australia.
Operation power:
The NT2-A is designed to operate from phantom power to the P48 standard. The NT2-A will
operate between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output
XLR connector.
Operation output impedance:
The NT2-A will operate satisfactorily into a load impedance as low as 1 kΩ. If a load below this
is used, the output signal level will be reduced. The NT2-A output is balanced between pin 2 (hot)
and pin 3 (cold). Pin 1 is ground.
Acoustic principle: Externally polarized 25 mm (1?) dual diaphragm.
Directional pattern: Multi-pattern
Frequency range:  20 Hz ~ 20 000 Hz
Output impedance: 200 Ω
Signal noise ratio din iec 651:
87 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 7 dBA SPL (per IEC651, IEC268-15)
Maximum spl:
147 dB (@ 1% THD into 1 kΩ); 157 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity: -36 dB re 1 Volt/Pascal; (16 mV @ 94 dB SPL) +/-2 dB
Dynamic range din iec 651: 140 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Output connection:
3 pin XLR, balanced output between; pin 2(+) and pin 3(-); Pin 1 ground
Weight with battery: 860 grm

Weight3.00 kg3.00 kg0.82 kg0.46 kg0.40 kg2.90 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 3.00 kg
Weight 3.00 kg
Weight 0.82 kg
Weight 0.46 kg
Weight 0.40 kg
Weight 2.90 kg