| Content |
Carefully selected for their nearly identical response, matched pairs of Pulsar II microphones from M-Audio® deliver superior stereo performance. The brass bodies are equipped with internal shockmounts and low-noise transformerless electronics. Each microphone offers a switchable 10 dB attenuation pad, plus an 80 Hz low-cut filter. Together, these functions allow the Pulsar II microphones to adapt to a variety of applications. The included hardware package allows Pulsar II microphones to be mounted in either an X-Y or ORTF (110º) stereo configuration. While ideal for stereo use, these microphones can also be used independently in a wide range of critical recording situations. This complete package includes a stereo mounting bar, hard mounts, risers, windscreens, and cloth bags, as well as a handsome and functional wooden storage/travel case.
Full Features | | Two response-matched M-Audio Pulsar II microphones | | | 0.75" diameter, 6-micron sputtered gold diaphragms | | | Cardioid pickup patterns | | | Class A FET transformerless electronics | | | Brass bodies with internal shockmounts | | | Switchable 10 dB pads and 80 Hz filters (18 dB/octave) | | | 48 Volt phantom power required | | | Includes stereo bar, hard mounts, risers, wind screens, and soft bags-all in a wooden travel case |
Specifications | | Type: | Large diaphragm condenser, gold evaporated | | | Polar pattern: | Cardioid | | | Frequency response: | 20 Hz-20 kHz | | | Sensitivity: | 13.8 mV/Pa (-37dBV) | | | Max. SPL ( |
|
NT2-A - ?The Legend Continues? Multi Pattern 1? Condenser Microphone.
The new NT2-A carries on the tradition forged by the now legendary R?DE NT2.
A professional large capsule (1?) studio microphone incorporating three-position
pick-up patterns, pad and high pass filter switches conveniently located on the
mic body.
At the heart of the NT2-A is the Australian designed and manufactured HF1 dual
diaphragm capsule. The frequency and transient response of this new transducer
has been voiced to complement today?s modern recording techniques, and yet still
evoke the silky smooth character of the legendary microphones of the 50?s and 60?s.
These features provide the flexibility and superlative audio characteristics that make
the NT2-A one of the most versatile condenser mics available.
The NT2-A?s variable controls allow switching between Omni, Figure 8, and Cardioid
polar patterns. The three position high-pass filter provides a flat response or an 80Hz
and 40Hz high pass filter to be selected. Finally the microphones Pad can be switched
between 0 dB, -5dB and -10dB. The NT2-A comes in a soft pouch with an M2 stand mount.
SPECIFICATIONS:
Features:
The Australian designed and manufactured HF1 1? edge terminated, gold sputtered, dual
5 um diaphragm capsule. 3-position variable polar pattern: Omni, Cardioid & Figure 8; all
controlled on the mic. 3-position variable high-pass filter: Flat, 80 Hz or 40 Hz. 3-position
variable pad: 0 dB, -5 dB or -10 dB. Ultra low noise, transformerless SMT circuitry. Wide
dynamic range. High strength heat-treated steel mesh head. Durable satin nickel finish.
Internal capsule shock mounting. Supplied complete with soft pouch and clip. Designed
and manufactured in Sydney, Australia.
Operation power:
The NT2-A is designed to operate from phantom power to the P48 standard. The NT2-A will
operate between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output
XLR connector.
Operation output impedance:
The NT2-A will operate satisfactorily into a load impedance as low as 1 kΩ. If a load below this
is used, the output signal level will be reduced. The NT2-A output is balanced between pin 2 (hot)
and pin 3 (cold). Pin 1 is ground.
Acoustic principle: Externally polarized 25 mm (1?) dual diaphragm.
Directional pattern: Multi-pattern
Frequency range: 20 Hz ~ 20 000 Hz
Output impedance: 200 Ω
Signal noise ratio din iec 651:
87 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 7 dBA SPL (per IEC651, IEC268-15)
Maximum spl:
147 dB (@ 1% THD into 1 kΩ); 157 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity: -36 dB re 1 Volt/Pascal; (16 mV @ 94 dB SPL) +/-2 dB
Dynamic range din iec 651: 140 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Output connection:
3 pin XLR, balanced output between; pin 2(+) and pin 3(-); Pin 1 ground
Weight with battery: 860 grm |
Behringer B-5 Sputtered Diaphragm Studio Condenser Microphone
The B-5 is a professional gold-sputtered diaphragm condenser microphone featuring two interchangeable capsules for different pickup patterns (cardioid and omnidirectional). It is perfect for acoustic instruments, vocals and overhead miking. Its ultra low-noise transformerless FET input eliminates low frequency distortion. The -10 dB attenuator can be used with high volume signal sources, while the low-cut filter eliminates floor rumble. The microphone is delivered in a rugged hard case with stand adapter and windscreen.
|
|
|
|
|
|
|
Professional true condenser microphone for studio and live applications
|
|
|
2 interchangeable capsules with cardioid and omnidirectional pickup patterns
|
|
|
Low-mass gold sputtered diaphragm for ultimate sound reproduction
|
|
|
Perfect for acoustic instruments, voice and overhead etc.
|
|
|
Ultra low-noise transformerless FET input eliminates low-frequency distortion
|
|
Smooth, super-wide frequency response and incredible musicality
|
|
Switchable low-frequency roll-off and -10 dB input attenuation
|
|
Gold-plated 3-pin XLR output connector
|
|
Rugged construction with satin nickel-plated brass body
|
|
Custom microphone stand adapter, windscreen and transport case included
|
|
Manual Download |
| Acoustical operating principle | Pressure gradient transducer | | Directional pattern | Cardioid | | Frequency range | 20 Hz ... 20 kHz | | Sensitivity at 1 kHz into 1 kohm | 13 mV/Pa | | Rated impedance | 50 ohms | | Rated load impedance | 1000 ohms | | Equivalent noise level, CCIR1) | 23 dB | | Equivalent noise level, A-weighted1) | 12 dB-A | | Signal-to-noise ratio, CCIR1) (rel. 94 dB SPL) | 71 dB | | Signal-to-noise ratio, A-weighted1) (rel. 94 dB SPL) | 82 dB | | Maximum SPL for THD | 110 dB | | Maximum SPL for THD | 129 dB | | Maximum output voltage for THD | -1 dBu | | Dyn. range of the mic. amplifier /A-weighted, 0.5 %2)) | 98 dB | | Dyn. range of the mic. amplifier /A-weighted, 5 %2)) | 117 dB | | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | | Current consumption (P48, IEC 61938) | 3.2 mA | | Matching connector | XLR 3F | | Weight | 825 g | | Diameter | 78 mm | | Length | 165 mm |
1) According to IEC 60268-1; CCIR-weighting according to CCIR 468-3, quasi peak; A-weighting according to IEC 61672-1, RMS
2) Measured as equivalent el. input signal |
|
| Behringer C-1 Studio Condenser Microphone
Behringer C-1 Studio Condenser Microphone
The C-1 Studio Condenser Microphone from Behringer offers a cardioid pickup pattern for maximum sound source separation and feedback rejection. This low noise microphone is suitable for a wide range of recording scenarios, including project, professional, and home studio applications. There is a pressure gradient transducer and a shock-mounted large diaphragm capsule for open, transparent sound with high-quality transient response. It is constructed of a die-cast metal body for durability and features an LED light to indicate when the microphone is receiving phantom power. The C-1 includes a swivel mount and custom case.
- Professional large-diaphragm condenser microphone for unsurpassed audio quality
- Ideal as main and support microphone for studio and live applications
- Exceptionally flat frequency response and ultra-high sound resolution
- Cardioid pickup pattern for outstanding sound source separation and feedback rejection
- Ultra low-noise transformerless FET input circuitry
- LED indicates phantom power operation
- Gold-plated 3-pin XLR output connector for perfect signal transmission
- Ultra-rugged construction with die-cast body
- Swivel stand mount and carrying case included
| Operating Principle |
Pressure Gradient |
| Capsule |
Condenser |
| Diaphragm |
0.63" / 16.0 mm |
| Polar Pattern |
Cardioid |
Performance
| Frequency Range |
40 Hz to 20 kHz |
| Maximum SPL |
136 dB SPL |
| Impedance |
100 Ohms |
| Load Impedance |
1000 Ohms |
| Sensitivity |
-33 dB |
| THD |
1% |
Connectivity
| Output Connectors (Analog) |
1 x XLR 3-Pin |
Power
| Operating Voltage |
36 to 52 V |
| Operating Current Consumption |
2.5 µA |
Physical
0.93 lb / 0.42 kg
| Dimensions |
ø: 2.13 x L: 7.09" / ø: 54 x L: 180 mm |
| Weight |
|
| Live sound
| Podcasting
Home recording
Vocals
Musical instruments |
Perception 120 |
|
- General-purpose cardioid recording microphone
- Extended frequency response
- Roadworthy construction
- Switchable 20 dB preattenuation pad
- Switchable bass cut filter
- Designed and engineered by AKG in Vienna, Austria
The Perception 120 is a 2/3-inch diaphragm true condenser microphone that offers solid build quality, outstanding performance, and excellent value. The low-mass diaphragm delivers a clear sound with accurate sonic detail. A switchable 20 dB preattenuation pad and bass cut filter make the Perception 120 an excellent choice for a wide range of recording and live sound applications.
Backed by AKG\'s six decades of experience in making microphones and input from sound engineers around the world, the Perception 120 now brings AKG studio quality to musicians and project studio applications.
| Type |
2/3\" Diaphragm True Condenser |
| Polar pattern |
cardioid |
| Frequency range |
20 to 20,000 Hz |
| Sensitivity |
22 mV/Pa (-33 dBV) |
| Max. SPL |
130/150 dB (0/-20 dB) for 0.5% THD |
| Equivalent noise level |
22 dB-A (IEC 60268-4) |
| Signal/noise ratio (A-weighted) |
72 dB |
| Preattenuation pad |
0 dB, -20 dB |
| Bass filter |
12 dB/octave at 300 Hz |
| Impedance |
|
| Recommended load impedance |
>= 1,000 ohms |
| Powering |
|
| Power requirement |
48 V phantom power to DIN/IEC |
| Connector |
3-pin XLR |
| Finish |
metallic blue |
| Dimensions |
53 dia. x 165 mm (2.1 dia. x 6.5 in.) |
| Net weight |
525 g (18.5 oz.) |
| Shipping weight |
955 g (33.7 oz.) |
|
Reviews
There are no reviews yet.