MC2 Audio T2000 POWER AMPLIFIER 2 x 1150w 230V

Number of Channels: 2

Output Power: (per channel)

8 ohms 625W
4 ohms 1150W
2 ohms 2100w


Output Power: (bridged)

8 ohms 2300W
4 ohms 4200w


THD%: (@1dB below max output)

@ 1kHz 20Hz to 20kHz
Gain / Sensitivity:

Gain 32/36dB
Sensitivity (for max power) +7.5/3.5dBu (1.8/1.2V)


Frequency Response: 20Hz to 20kHz (+ 0/- 0.5dB)

Power Consumption:

Nominal @ 240v into 4 ohms 2.8A
Nominal @ 120v into 4 ohms 5.6A

Dimensions: (2U) (mm)

Amplifier 88(h) x 482(w) x 460(d)
Single Box (UK shipping) 230 x 580 x 560
Double Box (outside UK) 250 x 610 x 600

Weight:

Amplifier 20.4kg
Boxed (shipping weight) 22.2kg

User's Manual

Crown DSi 4000 2x1200W-4Ω Power Amplifier

The Crown? DSi 4000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply. A rear-panel HD-15 connector shall
provide input/output connectivity between the DSi amplifi er and the DSi-8M
System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items and front panel lockout.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, illuminates when a very low-level
signal is present at input.
?10 Indicator: Green LED fl ashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED fl ashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp Indicator: Red LED, one per channel, illuminates under excessive temperature
conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Stereo (per channel): 1,600W with 1% THD, 4 ohm
Stereo (per channel): 1,200W with 0.5% THD, 8 ohm Stereo (per channel):
650W with 0.5% THD, 4 ohm Bridge-Mono: 3,200W with 1% THD, 8 ohm
Bridge-Mono: 2,400W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 3.61V.
Sensitivity at 4 ohm rated output: 3.47V.
Sensitivity at 2 ohm rated output: 2.84V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 8.0A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
Input EQ: 6 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
Also adjustable high and low shelving fi lters. This 8-fi lter EQ section can be
bypassed.
Crossover Filters: Highpass and lowpass per channel. Butterworth 6/12/18/24
dB per octave, Linkwitz-Riley 24/48 dB per octave. Also includes ±15 dB bandpass
gain and polarity control.
Output EQ: 8 parametric fi lters per channel with adjustable Q, ±15 dB boost/cut.
This 8-fi lter EQ section can NOT be bypassed. Filters are enabled individually.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Delay: Up to 50 msec total delay per channel.
Presets: 20 presets. One is ?DSP OFF.? Fifteen are factory-set for JBL Cinema
systems. Four are user-defi nable.
Protection shall include the following:
DSi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airflow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg)
The amplifier shall be designated the Crown DSi 4000.

This professional stereo power amplifier, working in class-H mode, provides 2x1600W, at an efficiency of around 85%.
A massive transformer based power supply and hand selected components makes this power rating possible with exceptional audio quality and absolute reliability, even in the 2 Ohm mode.
The output stage is fully protected against over-temperature, short circuit, RFI and equipped with soft start circuit and temperature-controlled fan cooling.
The integral soft clip limiter protects against damage to the connected loudspeakers.
The activity of a protective circuit, signal and limiter is shown for each channel by LEDʼs.

Power Rating

Stereo Mode:
8Ω EIA 1 kHz 1% THD - 800W
4Ω EIA 1 kHz 1% THD - 1250W
2Ω EIA 1 kHz 1% THD - 2000W


Bridged Mono:
8Ω EIA 1 kHz 1% THD - 2600W
4Ω EIA 1 kHz 1% THD - 4000W

Damping Factor     Not Specified By Manufacturer
Input Sensitivity     26dB Setting - 3.92V
32dB Setting - 1.96V
Input Impedance     > 10kΩ balanced, or unbalanced
Gain     36.4dB
Frequency Response     20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio     -105dB
Total Harmonic Distortion (THD)     0.02% @ 2Ω
0.005-0.01% @ 4Ω
0.002-0.01% @ 8Ω
Input Connections     Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors     Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel     AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear)     Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators     Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution     Flow-thru air path and solid aluminum heat sinks
Power Consumption     120V 50/60Hz - 12A
230V 50Hz - 7A
Power Requirements     Not Specified By Manufacturer
Dimensions (WxHxD)     19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight     33.5 lbs (15.2kg)
Specialties     Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity

XR Series - Intelligent Power
New Horizons.

A lightweight with enormous power output. Combined with digital signal processing.
That's what we call flexibility! Locally controlled or completely networked.
No matter what the requirements are.
The integrated powerful digital signal processor (DSP) and controller allows
for a troublefree and easy adjustment to any acoustical environment.
Wear-free digital potentiometers, sequential remote power on,
alive contacts for easy supervision, computer controlled monitoring -
 its enless list of useful feature make it the right choice for any installation.
XR - the new definition of Intelligent Power

High Tech SMT Design
Digital Signal Processor
Excellent sound and superior impulse response
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX / Speakon
High-End Switched Power Supply with Power Factor Correction (not XR4000)
LED Indicators for SIGNAL, CLIP, PROTECT, POWER
Temperature controlled, variable speed low noise fans
Digital wear-free Volume Controls (can be operated manually)
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Paging Input
Monitor Output
SXL Dataport
Perfect Weight-to-Power ratio
3 Years Warranty

Technical Data:
XR 2500:  2x 1600 W @ 2 Ohm
                2x 1250 W @ 4 Ohm
Class:  H
Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB)
THD:  < 0.02%
Signal-to-Noise Ratio:  < -106 dB
Channel Seperation:  > 85 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Damping Factor:  750 to 1200 @ 4 Ohm
Cooling:  4 Fans (temp. reg. variable speed)
Weight:  9 kg
Dimensions:  2 RU / 483 x 88 x 454 mm(19" x 3.5" x 17.9“)