| Content |
The new AT2010 is designed to bring the studio-quality articulation and intelligibility of Audio-Technica's renowned 20 Series to the stage, for crystal-clear vocal performances. Featuring the same 16 mm low-mass diaphragm found in the critically acclaimed AT2020 side-address studio condenser, the AT2010 excels wherever articulate vocals are needed: in houses of worship, for solo performances, jazz vocalists, singer/songwriters, and more.
- Extended frequency response and superior transient response for smooth, natural sonic characteristics
- High SPL-handling and wide dynamic range provide unmatched versatility
- Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of desired sound source
- Multi-stage grille design offers excellent protection against plosives and sibilance without compromising high-frequency clarity
- Corrosion-resistant contacts from gold-plated XLRM-type connector
- Rugged, all-metal and construction for years of trouble-free service
- Quiet-Flex stand clamp provides silent, flexible microphone positioning
- Element: Fixed-charge back plate permanently polarized condenser
- Polar Pattern: Cardioid
- Frequency Response: 40-20,000 Hz
- Open Circuit Sensitivity: 48 dB (3.9 mV) re 1V at 1 Pa
- Impedance: 100 ohms
- Maximum Input Sound Level: 136 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 113 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 71 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 48V DC, 2 mA typical
- Weight: 233 g (8.2 oz)
- Dimensions: 179.1 mm (7.05“) long, 50.8 mm (2.00“) maximum body diameter
- Output Connector: Integral 3-pin XLRM-type
- Accessories: AT8470 Quiet-Flex stand clamp for 5/8“-27 threaded stands; 5/8“-27 to 3/8“-16 threaded adapter; soft protective pouch
| AKG C411L Ultralight Condenser Microphone
- Ultra-light vibration pickup
- Condenser transducer in sealed enclosure
- Cable with lockable miniature XLR connector
Weighing only 18 grams (0.6 oz.), this ultra-light condenser pickup is ideal for acoustic guitar, mandolin, violin, and most other stringed instruments. The C 411 will give a clear and uncolored sound without changing the balance of the instrument. Attaching the C 411 on or near the bridge or anywhere else on the instrument is easy with the included non-marring, reusable, solventfree adhesive compound.
C 411 L: With mini XLR connector for use with B 29 L battery operated power supply, MPA V L external phantom power adapter, or AKG WMS bodypack transmitters.
| Frequency range |
10 to 18,000 Hz |
| Max. SPL |
100 dB (for 1% THD) |
| Impedance |
200 ohms unbalanced |
| Recommended load impedance |
>=1000 ohms |
| Supply voltage |
9 to 52 V phantom power to DIN 45596 or battery powering from B 29 L or AKG bodypack transmitter |
| Current consumption |
approx. 2.2 mA |
| Connector |
C 411 L: 3-pin mini XLR |
| Cable |
C 411 L: 1.5 m (5 ft.) |
| Finish |
matte black |
| Dimensions |
27 x 14 x 9.5 mm / 1.1 x 0.5 x 0.3 in. |
| Net weight |
C 411 L: 18 g / 0.7 oz. |
| Shipping weight |
C 411 L: 150 g / 5.5 oz. |
| This new mic is a performance / price breakthrough. It has an acoustically identical version of the legendary CK1 capsule that is permanently mounted. This combination can handle high output transients as well as subtle harmonics. Also included are switchable 75 and 150Hz 12dB per octave rolloff, and switchable -10 & -20 dB input pad. It is a single pattern (cardioid), and has a frequency response of 20 to 20kHz with 135 dB SPL. Requires 12 to 48V phantom power. Kit comes with bag, windscreen and clip.
For more than twenty years, the AKG C 451 with the CK 1 condenser capsule was a standard item on tour riders for sound companies and required by leading engineers for studio projects. When it was discontinued in 1993, there was still a big demand for this microphone. AKG now has an updated version of this classic microphone.
The new C 451B provides the same frequency response as the legendary CK 1 with the same slight high-end rise that was the signature of the original. This characteristic makes the C 451B an ideal tool for capturing signals rich in transients such as acoustic guitars, snare drums, hi-hats and for overhead micing of drum kits. The C 451B?s response eliminates the need for heavy EQ on these instruments.
The new C 451B has also benefited from newer electronic technology with machine soldering and surface-mount components that improve noise performance and make the microphone much more reliable than the original.
Other special features include switchable 10 dB and 20 dB preattenuation pads and switchable low cut filters at 75 Hz or 150 Hz. Standard accessories included are an SA 40 stand adaptor, W 90 windscreen and a rugged zippered bag. Each C 451B also comes with an individual frequency response printout.
Three-year warranty.
Specification
Polar pattern: cardioid
Frequency range: 20?20,000 Hz
Sensitivity: 9 mV/Pa (-41 dBV re 1 V/Pa)
Max. SPL for 0.5 % THD: 135/145/155 dB SPL (-0/-10/-20 dB)
Equivalent noise level: 18 dB-A to DIN 45 412
Signal/noise ratio (A-weighted): 76 dB
Preattenuation pad: switchable, 0, -10,-20 dB Bass cut filter: switchable to flat or 12 dB/octave at 75 Hz or 150 Hz
Electrical impedance: Recommended load impedance: >1.000 Ohms
Power requirement: 9?52 Volt phantom power to DIN 45 596/IEC 268-15
Current consumption: Connector: 3-pin male XLR
Finish: satin nickel plated
Size: dia.: 190 mm (0.7 in.); length: 160 mm (6.3 in.)
Net/shipping weight: 125/760 g (4.4 oz./1.7 lbs.)
Standard accessories: W 90 windscreen, SA 40 stand adapter |
The e 914 is a high grade condenser microphone for very demanding applications.
Its outstanding sound properties qualify the e 914 for highly sophisticated tasks.
The e 914 is a perfect microphone for ambitious recordings and live performances.
Its main areas of application are acoustic guitars, cymbals, percussion, overhead,
orchestras, grand pianos etc .
Features
Exceptionally lively, clear sound
Three-position sensitivity switch
Three-position bass roll-off/cut-off switch
Very high sound pressure handling capability
Exchangeable microphone capsule
Delivery Includes
e 914 microphone
Microphone clamp
Windscreen
Pouch
User manual
Technical Data
Pick-up pattern cardioid
Frequency response 20...20 000 Hz
Sensitivity in free field, no load (1kHz) 7 mV/Pa
Equivalent noise level 19 dB(A)
Attenuation 0, -10, -20 dB
Max. Sound pressure level (aktiv) 137, 147, 157 dB
Nominal impedance 100 Ohm
Min. terminating impedance 1000 Ohm
Dimensions 24 x 157 mm
Weight 198 g
| The NT5 matched pairs are a masterpiece of small-diaphragm cardioid-
condenser microphone design.Intended for recording acoustic instruments,
drum overheads, cymbals and live performances, the compact externally
polarized mic employs a .5? capsule, an active J-FET impedance converter
with bipolar output buffer.
Finished in durable satin nickel, the NT5 is intended for either single or stereo
X/Y mic set-ups. The NT5 matched pairs comesupplied in a custom carry case
with windshields and mounts.
SPECIFICATIONS:
Acoustic principle: Externally polarised single diaphragm
Directional pattern: Cardioid
Frequency range: 20Hz - 20kHz
Output impedance: 100?
Signal noise ratio din iec 651: 78dB
Equvalent noise: Maximum spl: 143 dB @ 1% THD into 1k_
Sensitivity:
-38 dB re 1v/Pa ± 2 dB equivalent to 12mV/Pa where 1 Pa = 94dBSPL
Power supply voltage: P48 Supply (38V?52V), P24 Supply (20V-26V)
Current consumption: 4 mA, 2 mA,
Weight: 100g |
The ME 62 is an omni-directional microphone head suitable for K6 and K6P
powering modules. It can be used for reporting, discussions and interviews.
The ME 62 is particularly suitable for good reproduction of 'room' ambience
and 'spaced omni' stereo recording. Matt black, anodised, scratch-resistant finish.
Features
Omni-directional pick-up pattern
Minimal inherent self-noise
Excellent rejection of rumble, wind and handling noise
Wide frequency response
High maximum sound pressure level
Integral pop filter
Delivery Includes
1 ME 62
Technical Data
Pick-up pattern omni
Sensitivity in free field, no load (1kHz) 31 mV/Pa +- 2,5 dB
Nominal impedance 200 Ohm (K6)
Min. terminating impedance 1000 Ohm (K6)
Equivalent noise level 15 dB
Equivalent noise level weighted as per CCIR 468-3 27 dB
Dimensions d 22,5 x 94 mm
Weight 30 g
|
Reviews
There are no reviews yet.