| Content |
The new AT2010 is designed to bring the studio-quality articulation and intelligibility of Audio-Technica's renowned 20 Series to the stage, for crystal-clear vocal performances. Featuring the same 16 mm low-mass diaphragm found in the critically acclaimed AT2020 side-address studio condenser, the AT2010 excels wherever articulate vocals are needed: in houses of worship, for solo performances, jazz vocalists, singer/songwriters, and more.
- Extended frequency response and superior transient response for smooth, natural sonic characteristics
- High SPL-handling and wide dynamic range provide unmatched versatility
- Cardioid polar pattern reduces pickup of sounds from the sides and rear, improving isolation of desired sound source
- Multi-stage grille design offers excellent protection against plosives and sibilance without compromising high-frequency clarity
- Corrosion-resistant contacts from gold-plated XLRM-type connector
- Rugged, all-metal and construction for years of trouble-free service
- Quiet-Flex stand clamp provides silent, flexible microphone positioning
- Element: Fixed-charge back plate permanently polarized condenser
- Polar Pattern: Cardioid
- Frequency Response: 40-20,000 Hz
- Open Circuit Sensitivity: 48 dB (3.9 mV) re 1V at 1 Pa
- Impedance: 100 ohms
- Maximum Input Sound Level: 136 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 113 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 71 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 48V DC, 2 mA typical
- Weight: 233 g (8.2 oz)
- Dimensions: 179.1 mm (7.05“) long, 50.8 mm (2.00“) maximum body diameter
- Output Connector: Integral 3-pin XLRM-type
- Accessories: AT8470 Quiet-Flex stand clamp for 5/8“-27 threaded stands; 5/8“-27 to 3/8“-16 threaded adapter; soft protective pouch
| AKG C411L Ultralight Condenser Microphone
- Ultra-light vibration pickup
- Condenser transducer in sealed enclosure
- Cable with lockable miniature XLR connector
Weighing only 18 grams (0.6 oz.), this ultra-light condenser pickup is ideal for acoustic guitar, mandolin, violin, and most other stringed instruments. The C 411 will give a clear and uncolored sound without changing the balance of the instrument. Attaching the C 411 on or near the bridge or anywhere else on the instrument is easy with the included non-marring, reusable, solventfree adhesive compound.
C 411 L: With mini XLR connector for use with B 29 L battery operated power supply, MPA V L external phantom power adapter, or AKG WMS bodypack transmitters.
| Frequency range |
10 to 18,000 Hz |
| Max. SPL |
100 dB (for 1% THD) |
| Impedance |
200 ohms unbalanced |
| Recommended load impedance |
>=1000 ohms |
| Supply voltage |
9 to 52 V phantom power to DIN 45596 or battery powering from B 29 L or AKG bodypack transmitter |
| Current consumption |
approx. 2.2 mA |
| Connector |
C 411 L: 3-pin mini XLR |
| Cable |
C 411 L: 1.5 m (5 ft.) |
| Finish |
matte black |
| Dimensions |
27 x 14 x 9.5 mm / 1.1 x 0.5 x 0.3 in. |
| Net weight |
C 411 L: 18 g / 0.7 oz. |
| Shipping weight |
C 411 L: 150 g / 5.5 oz. |
|
The ME 67 is a long gun microphone head designed for use with the K6 and K6P powering modules. A highly directional microphone, it can be used where the microphone must be placed at a distance from the sound source. Matt black, anodised, scratch-resistant finish.
Pick-up pattern : lobar
Sensitivity in free field, no load (1kHz) : 50 mV/Pa +- 2,5 dB
Nominal impedance : 200 Ohm (K6)
Min. terminating impedance : 1000 Ohm (K6)
Equivalent noise level : 10 dB
Dimensions : d 22,5 x 343 mm
Weight : 100 g
|
The e 865 is a fully professional super-cardioid vocal microphone utilising the very best in condenser microphone technology to achieve new standards of quality and sound. The microphone capsule insorporates special blast/pop protiction plate to shield the diaphragm from excessive sound pressure levels. ON/OFF Switch.
- Pick-up pattern : super cardioid
- Sensitivity in free field, no load : (1kHz) 3 mV/Pa
- Max. Sound pressure level (aktiv) : 150 dB
- Nominal impedance : 200 Ohm
- Min. terminating impedance : 1000 Ohm
- Dimensions : d 47 x 193 mm
- Weight : w/o cable 311 g
- Frequency response (microphone) : 40.....20000 Hz
- Phantom powering : 12 - 48 V
|
The e 914 is a high grade condenser microphone for very demanding applications.
Its outstanding sound properties qualify the e 914 for highly sophisticated tasks.
The e 914 is a perfect microphone for ambitious recordings and live performances.
Its main areas of application are acoustic guitars, cymbals, percussion, overhead,
orchestras, grand pianos etc .
Features
Exceptionally lively, clear sound
Three-position sensitivity switch
Three-position bass roll-off/cut-off switch
Very high sound pressure handling capability
Exchangeable microphone capsule
Delivery Includes
e 914 microphone
Microphone clamp
Windscreen
Pouch
User manual
Technical Data
Pick-up pattern cardioid
Frequency response 20...20 000 Hz
Sensitivity in free field, no load (1kHz) 7 mV/Pa
Equivalent noise level 19 dB(A)
Attenuation 0, -10, -20 dB
Max. Sound pressure level (aktiv) 137, 147, 157 dB
Nominal impedance 100 Ohm
Min. terminating impedance 1000 Ohm
Dimensions 24 x 157 mm
Weight 198 g
|
C 568 B
Compact, short shotgun microphone
Integrated, switchable bass cut filter minimizes mechanical noise
Operates on phantom power
High directivity and wide frequency response in a relatively short shotgun make this
microphone a perfect tool for theater, sound reinforcement, and film/TV applications.
Due to its compact and lightweight design, the C 568 B is ideal for camera mount
applications. Below 500 Hz it functions as a hypercardioid microphone; above 500 Hz
the acoustic interference tube introduces increasing directivity. A switchable 12 dB/
octave 120 Hz bass cut filter effectively suppresses rumble and wind noise. The rugged,
all-metal body contains the built-in preamp. Phantom powering (9?52 V) required; foam
windscreen and stand adapter included.
SPECIFICATIONS:
Polar pattern hypercardioid/directional
Frequency range 20 to 20,000 Hz
Sensitivity 11 mV/Pa (-39 dBV)
Max. SPL 128 dB
Equivalent noise level (CCIR 468-3) 29 dB
Equivalent noise level 18 dB-A
Signal/noise ratio 76 dB
Bass filter 12 dB/octave at 120 Hz
Impedance 600 ohms
Recommended load impedance >2000 ohms
Supply voltage 9 to 52 V phantom power to DIN 45596
Current consumption |
Reviews
There are no reviews yet.