| Content |
Ideal for professional recording and critical applications in broadcast, this versatile studio performer may be used with confidence in a wide variety of professional miking applications. Featuring direct-coupled balanced outputs for clean signals in high-output conditions, the microphone is totally free of the distortion associated with conventional transformer-coupled outputs. Its fast response to transients contributes to the open, transparent reproduction of even the most difficult-to-capture instruments. The microphone is fully RoHS-compliant - free from all substances specified in the EU directive on the reduction of hazardous substances (RoHS).
The AT4051b consists of two modular subassemblies: an AT4900b-48 body and an AT4051b-EL cardioid head capsule (both available separately). Additional interchangeable capsules are available in omnidirectional (AT4049b-EL) and hypercardioid (AT4053b-EL).
- Specially engineered to meet the most critical acoustic requirements of professional recording, broadcast and sound reinforcement
- High front-to-back rejection ratio cardioid polar pattern improves isolation of desired sound source
- Direct-coupled, balanced output results in a clean signal even under high-output conditions
- Transformerless circuitry virtually eliminates low-frequency distortion and provides superior correlation of high-speed transients
- Switchable 80 Hz hi-pass filter and 10 dB pad
- Rugged turned-brass microphone housing for enduring dependability
- State-of-the-art design and manufacturing techniques ensure compliance with Audio-Technica's stringent consistency and reliability standards
- RoHS-compliant - free from all substances specified in the EU directive on the reduction of hazardous substances (RoHS)
- Element: Externally polarized (DC bias) capacitor
- Polar Pattern: Cardioid
- Frequency Response: 20-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 12 dB/octave
- Open Circuit Sensitivity: -34 dB (19.9 mV) re 1V at 1 Pa
- Impedance: 50 ohms
- Maximum Input Sound Level: 145 dB SPL, 1 kHz at 1% T.H.D.; 155 dB SPL, with 10 dB pad (nominal)
- Dynamic Range: 129 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 78 dB, 1 kHz at 1 Pa
- Phantom Power Requirements: 48V DC, 4.8 mA typical
- Switch: Flat, roll-off; 10 dB pad (nominal)
- Weight: 126 g (4.4 oz)
- Dimensions: 155.0 mm (6.10“) long, 21.0 mm (0.83“) maximum body diameter
- Output Connector: Integral 3-pin XLRM-type
- Accessories: AT8405a stand clamp for 5/8“-27 threaded stands; windscreen; protective carrying case
|
Broadcast sound quality
Low noise circuitry
Rugged metal construction
Convenient digital switching
High Frequency Boost
High Pass Filter (Flat/75Hz)
PAD (-10db)
Ten year extended warranty with online registration
The NTG4 builds on the platform created by RØDE's award-winning NTG1 shotgun microphone. A broadcast-quality directional condenser microphone designed to provide premium audio recording in a versatile range of applications including on-camera and boom mounted.
Visit the NTG4 feature page
NTG4 Specifications
Acoustic Principle Line Gradient
Capsule 0.50“
Polar Pattern Supercardioid
Address Type End
Frequency Range 20Hz - 20kHz(selected HPF @75Hz)
Output Impedance 200Ω
Maximum SPL 135dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Sensitivity -32.0dB re 1 Volt/Pascal (25.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 16dB-A
Power Options +12V phantom power+24V phantom power+48V phantom power
Weight 126gm
Dimensions 225mmH x 22mmW x 22mmD
Output XLR Output
Warranty 1 year with free extension to 10 years following registration
|
The length (14.53“) of the AT8035 Line + Gradient Condenser Microphone is well-suited for ENG, outdoor recording and other specialized uses. The microphone is designed for video production and broadcast (ENG/EFP) audio acquisition. Suited for both boom & handheld use, it provides the narrow acceptance angle desirable for long-distance sound pickup, featuring excellent sound rejection from the sides and rear of mic and switchable low-frequency roll-off. It operates on battery or phantom power.
Designed for video production and broadcast (ENG/EFP) audio acquisition
Length is well-suited for ENG, outdoor recording and other specialized uses
Provides the narrow acceptance angle desirable for long-distance sound pickup
Excellent sound rejection from the sides and rear of mic
Switchable low-frequency roll-off
Operates on battery or phantom power
RoHS compliant - free from all substances specified in the EU directive on hazardous substances
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Line + gradient
Frequency Response: 40-20,000 Hz
Low Frequency Roll Off: 80 Hz, 12 dB/octave
Open Circuit Sensitivity: Phantom: -38 dB (12.5 mV) re 1V at 1 Pa Battery: 39 dB (11.2 mV) re 1V at 1 Pa
Impedance: Phantom: 250 ohms Battery: 300 ohms
Maximum Input Sound Level: Phantom: 132 dB SPL, 1 kHz at 1% T.H.D. Battery: 120 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: Phantom: 110 dB, 1 kHz at Max SPL Battery: 98 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 72 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 11-52V DC, 2 mA typical
Battery Type: 1.5V AA/UM3
Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
Switch: Flat, roll-off
Weight: 170 g (6.0 oz)
Dimensions: 369.0 mm (14.53“) long, 21.0 mm (0.83“) diameter
Output Connector: Integral 3-pin XLRM-type
Accessories: AT8405a stand clamp for 5/8“-27 threaded stands; 5/8“-27 to 3/8“-16 threaded adapter; AT8132 windscreen; battery; protective carrying case
| OLED display (on receiver)
One button pairing
Three level gain control
AA battery or USB powered
Includes RØDE\'s broadcast Lavalier microphone
RØDELink represents the next generation of digital wireless systems. Using a series II 2.4GHz digital transmission with 128-bit encryption, it is able to constantly monitor and hop between frequencies to maintain the strongest possible signal level at a range of up to 100 metres (over 100 yards). The RØDELink Filmmaker Kit provides everything you need to start shooting video wirelessly, including a receiver, transmitter and broadcast-grade lavalier microphone. The receiver (RX-CAM) features an OLED display with information on level, battery status (receiver and transmitter), mute and channel selection. The unit can be mounted on a standard camera shoe mount, 3/8" thread or belt-clip, and for added versatility the shoe mount can be located in one of two positions. The lightweight transmitter (TX-BELT) can be fitted to a belt or clothing and features a locking thread to ensure the microphone connection is as secure as possible. RØDEʼs omnidirectional Lavalier microphone is included in the kit to provide the highest possible audio reproduction quality.
RØDELink Filmmaker Kit Specifications
Transmission type 2.4GHz Fixed Frequency Agile System
System dynamic range 112dB
Range (distance) 100m
Frequency range 35Hz - 22kHz
Maximum output level 1v Rms (2.8v P-p)
Max input signal level 1v Rms (2.8v P-p)
Max latency 4ms
Receiver (RX-CAM)
Power source 2 X AA Battery Or MicroUSB
Antenna Internal
Output connection 3.5mm TRS Locking Jack Socket - Dual Mono
Output impedance 300Ω
Dimensions 111mm X 65mm X 52mm
Weight 190gm
Transmitter (TX-BELT)
Power source 2 X AA Battery Or MicroUSB
Antenna Internal
Output connection 3.5mm TRS Locking Jack Socket
Output impedance 10kΩ
Dimensions 111mm X 65mm X 40mm
Weight 190gm
Lavalier
Acoustic Principle Pressure Gradient
Active Electronics JFET impedance converter
Capsule 0.10“
Address Type End
Frequency Range 60Hz - 18kHz
Output Impedance 3000Ω
Maximum SPL 110dB SPL (@ 1kHz, 1% THD into 1KΩ load)
Maximum Output Level 189.0dBu (@ 1kHz, 1% THD into 1KΩ load
Sensitivity -33.5dB re 1 Volt/Pascal (21.00mV @ 94 dB SPL) +/- 2 dB @ 1kHz
Equivalent Noise Level (A-weighted) 25dB-A
Weight 1.00gm
Dimensions 12.00mmH x 4.50mmW x 4.50mmD
Warranty 10 year warranty |
he PRO24-CMF camcorder microphone is a lightweight, compact stereo condenser ideal for digital recording with high-fidelity stereo sound. Equipped with a windjammer, accessory shoe and permanently attached coiled cable, the microphone features a pair of cardioid elements in an X-Y configuration to provide the spatial impact and realism of a live sound field. The microphone is designed for either battery operation or battery-free operation when used with camcorders that provide plug-in power at the mic input. Like all Audio-Technica mics, the PRO24-CM is rugged; it's built to endure the rigors of field production. - Stereo microphone designed to attach to a camcorder
- For camcorders with an accessory shoe and stereo microphone input
- Lightweight, portable design with rugged all-metal construction
- Pair of cardioid condenser elements provides spatial impact and high-fidelity stereo sound image
- Battery-free operation when used with recording devices that provide plug-in power at the mic input
- On/off switch for convenient operation
- Includes camera-mount, windscreen, windjammer, battery and protective pouch
- Permanently attached 6""-12“" coiled cable with right-angle molded 3.5 mm stereo mini plug at output end
Polar Pattern: X/Y Stereo
Frequency Response: 100-17,000 Hz
Open Circuit Sensitivity: -50 dB (3.1 mV) re 1V at 1 Pa
Impedance: 600 ohms
Maximum Input Sound Level: 119 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: 82 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 57 dB, 1 kHz at 1 Pa
Battery Type: 1.5V LR44
Battery Current Life: 0.6 mA / 200 hours typical
Switch: On/off
Weight: 3.9 oz (111 g)
Dimensions: 4.59“" (116.5 mm) long, 0.83" (21.0 mm) maximum body diameter
Output Connector: 3.5 mm stereo mini plug on cable
Cable: Permanently attached 152.4 mm - 304.8 mm (6""-12"") coiled cable with right-angle molded 3.5 mm stereo mini-plug at output end
Accessories: Video-camera shoe mount; LR44 battery; windscreen; Fur windjammer AT8123 and soft protective pouch
|
Internally switchable proximity effect compensation and sensitivity reduction.
The BCM 104 condenser microphone is the first product in the new Broadcast Line,
which is especially tailored to the demands of professional radio announcing.
What sets the Broadcast Line apart is a completely independent, functionally-
optimized design derived from extensive 3D simulations.
The large-diaphragm condenser capsule used in the BCM 104 has a cardioid directional
pattern with internally switchable proximity effect compensation. A second switch allows
the sensitivity to be reduced by 14 dB.
The microphone headgrill twists off easily for quick cleaning. Neumann offers optional,
color-coded headgrills so that, for reasons of hygiene, each announcer working at an
announcing desk can use his or her individual headgrill.
Directly in front of the capsule, mounted on a frame holder, is a piece of fine gauze that
serves as a built-in popscreen.
The BCM 104 has an elastic mount against structure-borne noise, that is compatible with
standard broadcast-segment microphone arms.
Features:
Cardioid microphone for broadcast & studio
Large diaphragm condenser capsule with
switchable proximity compensation
Distinctive design
Integrated pop screen
Quick release head grille for easy cleaning
Individual head grilles available for each user
Acoustic features
The microphone headgrill houses the K 04 large-diaphragm capsule, which has a flat frequency
response up to 3 kHz. Higher frequencies have an increased presence of 2 dB maximum.
Since the above-mentioned microphone characteristics are obtained without the use of resonance
effects, the microphone features excellent transient response and transmits all transient phenomena
of music and speech without any coloration.
The integrated Pop Screen
A pop screen not only prevents the occurrence of plosive pop noises in vocal recordings, but also
efficiently prevents unwanted particles, from respiratory moisture, nicotine, to food remnants, from
settling on the diaphragm.
The pop screen can be removed for cleaning without the use of tools.
Electrical features
Instead of a transformer to couple the microphone output to the supply voltage, the BCM 104
has an electronic circuit which, like a transformer, provides for good common mode rejection.
Interference induced in the balanced modulation line is thus suppressed as usual.
With a very low self-noise of 7 dB(A), and an overload capability extending to 138 dB SPL,
the BCM 104 has a dynamic range of 131 dB (DIN/IEC 651).
Filter and Preattenuation
The BCM 104 amplifier has a linear operation down to 20 Hz. An active filter efficiently suppresses
signals below this frequency. In order to compensate for the proximity effect, a high-pass filter,
electronically activated by a switch, is built into the microphone. This filter reduces frequencies
below 100 Hz by 12 dB/octave.
A 14-dB preattenuation switch is provided in order to adjust the sensitivity, if necessary,
to transmission circuits designed for dynamic microphones. But this will increase the
self noise by 14 dB.Both switches are located inside the microphone housing, since they
will normally be operated only once, when the broadcasting facility is set up.
Mounting
The preferred mode of operation is to suspend the BCM 104 from a standard studio boom arm.
A thread adapter to fit different connector threads is included.
In order to provide protection from structure-borne noise, both the capsule and the microphone
in its mount are elastically suspended.
The optional SG 5 swivel mount allows additional angling of the BCM 104 by +/-90 degrees.
Application hint:
While designed to be an announcer's mic for broadcasting and studio, this is
just one of the most common applications. With additional experimentation,
you will gain maximum use from this microphone.
Technical Description:
Acoustical operating principle: Pressure gradient transducer
Directional pattern: Cardioid
Frequency range: 20 Hz -- 20 kHz
Sensitivity at 1 kHz into 1 kohm: 22 mV/Pa
-14 dB attenuation: 4.4 mV/Pa
Rated impedance: 50 ohms
Rated load impedance: 1000 ohms
Equivalent SPL CCIR 468-3: 18 dB
Equivalent SPL DIN/IEC 651: 7 dB-A
S/N ratio CCIR 468-3: 76 dB
S/N ratio DIN/IEC 651: 87 dB
Maximum SPL for THD 0.5%: 138 dB
Maximum SPL for THD 0.5% with preattenuation: 152 dB
Maximum output voltage: 10 dBu
Dyn. range of the mic. amplifier DIN/IEC 651: 131 dB
Supply voltage: 48 V +/- 4 V
Current consumption: 3.2 mA
Matching connector: XLR 3 F
Weight: 500 g
Diameter: 64 mm
Length: 85 mm
|
Reviews
There are no reviews yet.