AUDIO TECHNICA AT-LP3 Fully Automatic Belt-Drive Turntable With Preamplifier

Discontinued

239.99 incl. GR VAT

Out of stock

CompareAdd to wishlist Submit Better Price
  • Fully Automatic Belt-Drive system
  • Specially designed AT91R phono cartridge
  • Removable universal AT-HS3 headshell
  • Balanced straight tonearm
  • Switchable MM & MC modes
  • 33⅓ & 45 RPM selectable speeds
  • Fully Automatic Belt-Drive system
  • Specially designed AT91R phono cartridge
  • Removable universal AT-HS3 headshell
  • Balanced straight tonearm
  • Switchable MM & MC modes
  • 33⅓ & 45 RPM selectable speeds

 

Read more

Fully Automatic Belt-Drive Stereo Turntable with Universal Tonearm & Headshell
  • Fully Automatic Belt-Drive system
  • Specially designed AT91R phono cartridge
  • Removable universal AT-HS3 headshell
  • Balanced straight tonearm
  • Switchable MM & MC modes
  • 33⅓ & 45 RPM selectable speeds

A revolution in automation, the LP3 blends outstanding analogue sound with advanced features unique to a fully-automatic belt-drive turntable. Play 33⅓ & 45 RPM records with a pre-mounted AT91R Dual Moving Magnet phono cartridge whilst the tonearm’s removable universal headshell and switchable cartridge mode allows listeners to experiment with moving magnet and moving coil cartridges. Complete with a built-in phono pre-amplifier, the LP3 represents the next level for vinyl lovers.

  • Fully automatic belt-drive turntable operation with two speeds: 33-1/3, 45 RPM
  • Balanced straight tonearm with hydraulically damped lift control and lockable rest
  • Built-in switchable phono/line pre-amplifier with attached dual RCA output cable
  • Switchable modes for moving magnet and moving coil cartridges
  • AT91R Dual Moving Magnet™ phono cartridge and AT-HS3 universal headshell
  • Anti-resonance, die-cast aluminium platter with 4.5 mm thick rubber mat
  • Damped base construction for reduced low-frequency feedback colouration

Mm / Mc Cartridge Selector Switch

Switchable MM/MC mode allows the listener to use both Moving Magnet and Moving Coil cartridges on their LP3, allowing for greater sonic customisation – a unique feature not found on most turntables with a built-in phono preamplifier.

Cartridge & Stylus
Model AT91R
Type VM Dual Magnet
Output Voltage 3.5mV (mV at 1kHz, 5 cm/sec)
Vertical Tracking Force Range 1.5 to 2.5g (standard 2.0g)
Stylus Construction 0.6 mil bonded conical
Cantilever Aluminium pipe
Recommended Load Impedance 47,000 ohms
Weight 5.0g
Headshell
Model AT-HS3
Weight 11.1g
Overhang Adjustment 8mm
Tone arm
Type Static balanced straight shaped with soft damping control
Effective Length 221.5mm
Overhang 19mm
Maximum Tracking Error Angle Less than 3°
Stylus Pressure Adjustment Range 1 to 4g
Applicable Cartridge Weight 14.5 to 20g
Anti-skating Range 0 – 3 g
Turntable
Type Fully Automatic, Belt-Drive
Motor DC motor
Speeds 33-1/3 RPM, 45 RPM
Turntable Platter Die-cast aluminium
Wow and Flutter Less than 0.2% WRMS (33 1/3 RPM) at3kHz
Signal-to-Noise Ratio > 60 dB
Output Level “PHONO” (MM) 3.5mV nominal at 1kHz, 5cm/sec
“LINE” (MC) 220mV nominal at 1kHz, 5cm/sec
Phono Pre-Amp Gain 36dB nominal, RIAA equalised
56dB nominal, RIAA equalised
Power Supply Requirements 220 to 240 V / 50, 60 Hz
Power Consumption 2W
Dimensions 435 mm ×353 mm×128 mm (W×D×H)
Weight 5.2kg
Accessories Included Rubber mat, Dust cover, Platter (with drive belt), Counterweight, AT-HS3 Headshell with AT91R VM stereo cartridge, 45 RPM adapter, Power cable
Weight 7.00 kg

Reviews

There are no reviews yet.

Be the first to review “AUDIO TECHNICA AT-LP3 Fully Automatic Belt-Drive Turntable With Preamplifier”

Your email address will not be published. Required fields are marked *

Quick Comparison

AUDIO TECHNICA AT-LP3 Fully Automatic Belt-Drive Turntable With Preamplifier removeThorens TD 209 Turntable 45 rpm belt drive (black) removePro-Ject Debut Carbon DC OM10 Turntable Red removeTHORENS TD 206 Belt drive turntable (Black hg) removePro-Ject Elemental Phono USB + OM 5e Turntable White-Black removePro-Ject Debut Carbon DC OM10 Turntable Black Piano remove
NameAUDIO TECHNICA AT-LP3 Fully Automatic Belt-Drive Turntable With Preamplifier removeThorens TD 209 Turntable 45 rpm belt drive (black) removePro-Ject Debut Carbon DC OM10 Turntable Red removeTHORENS TD 206 Belt drive turntable (Black hg) removePro-Ject Elemental Phono USB + OM 5e Turntable White-Black removePro-Ject Debut Carbon DC OM10 Turntable Black Piano remove
Image
SKUATLP3TD 209DCOM10RTD 206 BLACK HGELEMENTALUSBWBDCOM10B
Rating
Price 239.99 incl. GR VAT1,065.00 incl. GR VAT449.00 incl. GR VAT1,065.00 incl. GR VAT335.00 incl. GR VAT449.00 incl. GR VAT
Stock

Out of stock

Available on backorder

In stock

Available on backorder

Only 1 left in stock (can be backordered)

In stock

AvailabilityOut of stockAvailable on backorderIn stockAvailable on backorderOnly 1 left in stock (can be backordered)In stock
Add to cart

Read more

Add to cart

Add to cart

Add to cart

Add to cart

Add to cart

Description
  • Fully Automatic Belt-Drive system
  • Specially designed AT91R phono cartridge
  • Removable universal AT-HS3 headshell
  • Balanced straight tonearm
  • Switchable MM & MC modes
  • 33⅓ & 45 RPM selectable speeds
ContentFully Automatic Belt-Drive Stereo Turntable with Universal Tonearm & Headshell
  • Fully Automatic Belt-Drive system
  • Specially designed AT91R phono cartridge
  • Removable universal AT-HS3 headshell
  • Balanced straight tonearm
  • Switchable MM & MC modes
  • 33⅓ & 45 RPM selectable speeds
A revolution in automation, the LP3 blends outstanding analogue sound with advanced features unique to a fully-automatic belt-drive turntable. Play 33⅓ & 45 RPM records with a pre-mounted AT91R Dual Moving Magnet phono cartridge whilst the tonearm’s removable universal headshell and switchable cartridge mode allows listeners to experiment with moving magnet and moving coil cartridges. Complete with a built-in phono pre-amplifier, the LP3 represents the next level for vinyl lovers.
  • Fully automatic belt-drive turntable operation with two speeds: 33-1/3, 45 RPM
  • Balanced straight tonearm with hydraulically damped lift control and lockable rest
  • Built-in switchable phono/line pre-amplifier with attached dual RCA output cable
  • Switchable modes for moving magnet and moving coil cartridges
  • AT91R Dual Moving Magnet™ phono cartridge and AT-HS3 universal headshell
  • Anti-resonance, die-cast aluminium platter with 4.5 mm thick rubber mat
  • Damped base construction for reduced low-frequency feedback colouration
Mm / Mc Cartridge Selector Switch Switchable MM/MC mode allows the listener to use both Moving Magnet and Moving Coil cartridges on their LP3, allowing for greater sonic customisation – a unique feature not found on most turntables with a built-in phono preamplifier.
Cartridge & Stylus
Model AT91R
Type VM Dual Magnet
Output Voltage 3.5mV (mV at 1kHz, 5 cm/sec)
Vertical Tracking Force Range 1.5 to 2.5g (standard 2.0g)
Stylus Construction 0.6 mil bonded conical
Cantilever Aluminium pipe
Recommended Load Impedance 47,000 ohms
Weight 5.0g
Headshell
Model AT-HS3
Weight 11.1g
Overhang Adjustment 8mm
Tone arm
Type Static balanced straight shaped with soft damping control
Effective Length 221.5mm
Overhang 19mm
Maximum Tracking Error Angle Less than 3°
Stylus Pressure Adjustment Range 1 to 4g
Applicable Cartridge Weight 14.5 to 20g
Anti-skating Range 0 - 3 g
Turntable
Type Fully Automatic, Belt-Drive
Motor DC motor
Speeds 33-1/3 RPM, 45 RPM
Turntable Platter Die-cast aluminium
Wow and Flutter Less than 0.2% WRMS (33 1/3 RPM) at3kHz
Signal-to-Noise Ratio > 60 dB
Output Level “PHONO” (MM) 3.5mV nominal at 1kHz, 5cm/sec "LINE” (MC) 220mV nominal at 1kHz, 5cm/sec
Phono Pre-Amp Gain 36dB nominal, RIAA equalised 56dB nominal, RIAA equalised
Power Supply Requirements 220 to 240 V / 50, 60 Hz
Power Consumption 2W
Dimensions 435 mm ×353 mm×128 mm (W×D×H)
Weight 5.2kg
Accessories Included Rubber mat, Dust cover, Platter (with drive belt), Counterweight, AT-HS3 Headshell with AT91R VM stereo cartridge, 45 RPM adapter, Power cable

Manual, Drive System belt-drive (flat belt around sub-platter), Speeds 33-1/3, 45 rpm, Tonearm THORENS TP 90, Pick-up Cartridge AT-95 B, Anti-skating (Bias) by magnet, Dimensions 470 x 125 x 430 mm (W x H x D), Weight 4.7 kg, power supply, RCA interconnects, stylus gauge, spirit level, cartridge alignment protractor

The first Debut turntable, introduced in the late 1990s, was a revolution for the hi-fi industry. For the first time after the arrival of Compact Disc and the assumed demise of vinyl records, an analogue product re-emerged in the "mass market” – something all music lovers could afford.  

The new DEBUT Carbon DC has been designed to set new standards in this category for the coming decade – perfectly timed as analogue today is again a respected source, while the demand for good turntables is growing again!  

The most obvious improvement is the inclusion of a CARBON TUBE for the tonearm, which increases stiffness and decreases unwanted resonance.  

This material normally is extensively used in high-end tonearms, but – because of cost reasons – was never used in products at lower price levels. Together with other improvements like an increase in platter size and weight to realize even smoother rotation, the overall sound quality is greatly improved. The approved belt drive design offers low noise AC motor with effective motor decoupling (utilising TPE-damping) and ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability without unwanted vibration.  

The DEBUT CARBON DC will be offered in high-gloss black or shiny red, green, blue, yellow, silver or white as no-added-cost option.

Specifications:

  •  8,6” carbon tonearm  

  •  Increased platter size with more weight  

  •  Precision belt drive with synchronous motor  

  •  New DC power supply with ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability.  

  •  New TPE motor suspension  

  •  Felt mat  

  •  magnetic cartridge options from Ortofon OM 10 or 2M red  

  •  7 high-gloss colours

A MUSICAL FAMILY

The TD 206 and TD 209 turntables are the younger siblings of the revolutionary, multiple-award-winning TD 309. However, they don’t have to live in the shadow of their older brother. Both models are built using only high-quality materials and parts. And both share a number of technical features with the TD 309, ensuring that their replay quality is up there with the best.

The new TP 90 tonearm is based on the tried-and-tested TP 92 and uses the same ultra-low-friction, high-performance bearing and the innovative zero-stiction anti-bias system. The arm tube is made from rolled aluminium that is damped using RMR technology (reduced-modal-resonance), and the stainless-steel counterweight at the end of the arm tube is double-decoupled. Tonearm height, azimuth and overhang are useradjustable.

SPECIAL FEATURES
  • Low Noise, Low Voltage electronically speed controlled DC Motor
  • Adjustable belt tension for best performance
  • Two-part aluminium/acrylic platter
  • New TP 90 tonearm with precision Japanese bearings
  • Tonearm adjustable for VTA, azimuth and overhang
  • Made in Germany

Best buy turntable with maximum simplicity, outstanding sound quality & USB recording capability!

Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental Phono USB table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it into hifi system and computer.

The only plastic here is the stylus guard!

The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards and vinyl recording capability.

• Belt drive system
• Integrated motor control with DC power supply secures silent running
• Central gravity mass point made from artificial stone
• Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom
• Low resonance MDF platter with felt mat
• 8,6” ultra low mass tonearm with straight arm tube
• Pre-adjusted tracking force & antiskating
• Gold-plated RCA contacts & cartridge pins
• Integrated phono stage with precise RIAA equalisation
• Line level output
• A/D converter for vinyl recording with USB B output

• Colour options: red-black, white-black, silver-black

The first Debut turntable, introduced in the late 1990s, was a revolution for the hi-fi industry. For the first time after the arrival of Compact Disc and the assumed demise of vinyl records, an analogue product re-emerged in the "mass market” – something all music lovers could afford.  

The new DEBUT Carbon DC has been designed to set new standards in this category for the coming decade – perfectly timed as analogue today is again a respected source, while the demand for good turntables is growing again!  

The most obvious improvement is the inclusion of a CARBON TUBE for the tonearm, which increases stiffness and decreases unwanted resonance.  

This material normally is extensively used in high-end tonearms, but – because of cost reasons – was never used in products at lower price levels. Together with other improvements like an increase in platter size and weight to realize even smoother rotation, the overall sound quality is greatly improved. The approved belt drive design offers low noise AC motor with effective motor decoupling (utilising TPE-damping) and ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability without unwanted vibration.  

The DEBUT CARBON DC will be offered in high-gloss black or shiny red, green, blue, yellow, silver or white as no-added-cost option.

Specifications:

  •  8,6” carbon tonearm  

  •  Increased platter size with more weight  

  •  Precision belt drive with synchronous motor  

  •  New DC power supply with ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability.  

  •  New TPE motor suspension  

  •  Felt mat  

  •  magnetic cartridge options from Ortofon OM 10 or 2M red  

  •  7 high-gloss colours

Weight7.00 kg5.00 kg6.50 kg6.00 kg3.50 kg6.50 kg
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 7.00 kg
Weight 5.00 kg
Weight 6.50 kg
Weight 6.00 kg
Weight 3.50 kg
Weight 6.50 kg