Content | Fully Automatic Belt-Drive Stereo Turntable with Universal Tonearm & Headshell
- Fully Automatic Belt-Drive system
- Specially designed AT91R phono cartridge
- Removable universal AT-HS3 headshell
- Balanced straight tonearm
- Switchable MM & MC modes
- 33⅓ & 45 RPM selectable speeds
A revolution in automation, the LP3 blends outstanding analogue sound with advanced features unique to a fully-automatic belt-drive turntable. Play 33⅓ & 45 RPM records with a pre-mounted AT91R Dual Moving Magnet phono cartridge whilst the tonearm’s removable universal headshell and switchable cartridge mode allows listeners to experiment with moving magnet and moving coil cartridges. Complete with a built-in phono pre-amplifier, the LP3 represents the next level for vinyl lovers.
- Fully automatic belt-drive turntable operation with two speeds: 33-1/3, 45 RPM
- Balanced straight tonearm with hydraulically damped lift control and lockable rest
- Built-in switchable phono/line pre-amplifier with attached dual RCA output cable
- Switchable modes for moving magnet and moving coil cartridges
- AT91R Dual Moving Magnet™ phono cartridge and AT-HS3 universal headshell
- Anti-resonance, die-cast aluminium platter with 4.5 mm thick rubber mat
- Damped base construction for reduced low-frequency feedback colouration
Mm / Mc Cartridge Selector Switch
Switchable MM/MC mode allows the listener to use both Moving Magnet and Moving Coil cartridges on their LP3, allowing for greater sonic customisation – a unique feature not found on most turntables with a built-in phono preamplifier.
Cartridge & Stylus |
Model |
AT91R |
Type |
VM Dual Magnet |
Output Voltage |
3.5mV (mV at 1kHz, 5 cm/sec) |
Vertical Tracking Force Range |
1.5 to 2.5g (standard 2.0g) |
Stylus Construction |
0.6 mil bonded conical |
Cantilever |
Aluminium pipe |
Recommended Load Impedance |
47,000 ohms |
Weight |
5.0g |
Headshell |
Model |
AT-HS3 |
Weight |
11.1g |
Overhang Adjustment |
8mm |
Tone arm |
Type |
Static balanced straight shaped with soft damping control |
Effective Length |
221.5mm |
Overhang |
19mm |
Maximum Tracking Error Angle |
Less than 3° |
Stylus Pressure Adjustment Range |
1 to 4g |
Applicable Cartridge Weight |
14.5 to 20g |
Anti-skating Range |
0 - 3 g |
Turntable |
Type |
Fully Automatic, Belt-Drive |
Motor |
DC motor |
Speeds |
33-1/3 RPM, 45 RPM |
Turntable Platter |
Die-cast aluminium |
Wow and Flutter |
Less than 0.2% WRMS (33 1/3 RPM) at3kHz |
Signal-to-Noise Ratio |
> 60 dB |
Output Level |
“PHONO” (MM) 3.5mV nominal at 1kHz, 5cm/sec
"LINE” (MC) 220mV nominal at 1kHz, 5cm/sec |
Phono Pre-Amp Gain |
36dB nominal, RIAA equalised
56dB nominal, RIAA equalised |
Power Supply Requirements |
220 to 240 V / 50, 60 Hz |
Power Consumption |
2W |
Dimensions |
435 mm ×353 mm×128 mm (W×D×H) |
Weight |
5.2kg |
Accessories Included |
Rubber mat, Dust cover, Platter (with drive belt), Counterweight, AT-HS3 Headshell with AT91R VM stereo cartridge, 45 RPM adapter, Power cable |
|
Best buy turntable with maximum simplicity, outstanding sound quality & USB recording capability!
Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental Phono USB table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it into hifi system and computer.
The only plastic here is the stylus guard!
The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards and vinyl recording capability.
• Belt drive system • Integrated motor control with DC power supply secures silent running • Central gravity mass point made from artificial stone • Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom • Low resonance MDF platter with felt mat • 8,6” ultra low mass tonearm with straight arm tube • Pre-adjusted tracking force & antiskating • Gold-plated RCA contacts & cartridge pins • Integrated phono stage with precise RIAA equalisation • Line level output • A/D converter for vinyl recording with USB B output
• Colour options: red-black, white-black, silver-black
| Fully automatic turntable for sophisticated demands with solid Makassar ebony console in luxurious equipment. Tonearm technology: Gimbal tonearm with mass-free contact force adjustment thanks to a high-precision torsion spring. Removable, torsion-resistant carbon fibre tonearm head with 13mm (1/2 inch) attachment.
Adjustable contact force and anti-skate.
Chassis technology: solid Makassar ebony console, floating subchassis, heavy sandwich platter with additional damping ring for maximum sound enjoyment.
- Drive technology: belt drive with polished flat belt
- DC motor with electric Speed control
- Viscosity damped tonearm lift
- Automatic tone arm attachment
- End shut-off with tone arm recirculation.
- Playback option for 78 rpm archive records.
Functions
Frequency Response
20 Hz - 22kHz
Power
Power Supply
2 V DC, 150 mA
Dimensions
| Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight ultra low mass tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it in.
The only plastic here is the stylus guard. The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
- Belt drive system with low vibration DC motor
- Central gravity mass point made from artificial stone
- Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom
- Low resonance MDF platter with felt mat
- 8,6” ultra low mass tonearm with straight arm tube
- Pre-adjusted tracking force & antiskating
- Gold-plated RCA contacts & cartridge pins
- Colour options: red-black, white-black, silver-black
Specifications:
- speed : 33, 45 (manual speed change)
- Speed variance: 33: 0,2% 45: 0,18%
- Wow & flutter: 33: 0,14% 45: 0,13%
- platter: 300mm MDF
- tonearm: 8,6” metal tube
- effective arm length: 218,5 mm
- overhang: 22,0 mm
- effective tonearmmass: 8,0gr
- counterweight for cartridge mass: 3 - 5,5g (included)
- tracking force range: 0 - 30mn (OM5 18mn pre-adjusted)
- output: RCA to phono input
- included accessory: RCA cable, 15V DC power supply
- power consumption: 4,0 watts
- dimensions: 430 x 90 x 300mm (WxHxD)
- weight: 2,7 kg net
|
Specifications
Item name: Turntable
Item code: Q1-USB
Brand:JBSYSTEMS
Brief Introduction
1.Plastic dust cover
2.USB-output for direct recording to any PC
3.Belt Drive 2 speed
:: Product Description
* Middle Torque belt drive motor
* Fast start / stop
* 2 speeds: 33, 45 rpm
* +/-10% Pitch adjustment range
* USB-output for direct recording to any PC
* Free, multilingual Audacity software available via download:
* - Endless possibilities with free downloadable effect plug-ins
* - Import, export and edit Ogg Vorbis, MP3, AIFF and WAV sound files.
* - Cut, copy, splice, and mix sounds together.
* - Change the speed or pitch of a recording.
* - Remove static, hiss, hum, or other constant background noises.
* - Alter frequencies with Equalization, FFT Filter, and Bass Boost effects.
* - Adjust volumes with Compressor, Amplify, and Normalize effects.
* - Many more…
* Selectable phono/line output
* All functions are equipped with stylish, blue LED lights
* Plastic dust cover
* Retractable target light
* Audio Technica cartridge included
* All metal S-shaped tone arm assembly with:
* - Counterweight * - Anti-skating adjustment
* - Lever lift with height adjustment
* Adjustable large feet for perfect leveling
:: Technical Information
* Motor: DC motor
* Driving Method: Belt Drive
* Starting Time: less than 1 second
* Braking Time: less than 1 second
* Speed selection: 331/3 ~ 45 RPM
* Speed adjustment: +/-10%
* Wow & Flutter: less than 0,25% WRMS (JIS WTD) @ 331/3 RPM
* Tone arm type: Static balanced S-shaped tone arm.
* Tracking Error angle: Less than 3°
* Cartridge weight: 3,5~8,5g.
* Anti-skate range: 0~7g.
* Phono output: 1,5 ~ 3,6mV @ 1kHz 5cm/sec (with supplied AT HP-4005 cartridge)
* Line output: 90 ~ 216mV @ 1kHz 5cm/sec (with supplied AT HP-4005 cartridge)
* Computer interface USB 1.1 compliant (Windows(R) XP/Vista/Win7 or Mac(R) OS X)
* Power supply: 230V~ 50Hz.
* Power consumption: 14Watts
* Dimensions: 450 x 350 x 150mm (WxDxH)
* Weight : 9,0kg.
|
A quiet-running synchronous motor with silicone belt is driving a low-resonance platter made from MDF. A new motor control with DC power supply minimzes unwanted vibration effectively. The main platter bearing consists of stainless steelspindle and bronze bushing with Teflon bottom to seccure low friction.
The main chassis is made from lightweight, but very stiff particle board. Essential II utilises a straight 8,6" aluminium tonearm design made from a single piece of aluminium with sapphire bearings, which offers a far better „plug & play" solution, than itʽs predecessor. Special feet effectively decouples the turntable from the surface.
Specifications:
-
speed : 33, 45 (manual speed change)
-
principle : belt drive
-
Speed variance : 33: 0,14% 45: 0,25%
-
Wow & flutter : 0,12%
-
platter : 300mm MDF with felt mat (0,8kg)
-
main bearing : stainless steel
-
tonearm : 8,6” aluminium
-
effective : arm length 218,5 mm
-
overhang : 22,0mm
-
effective tonearmmass : 8,0gr
-
counterweight for mass : 3 - 5,5g (included)
-
tracking force range : 0 - 25mn (OM5 18mn recommended)
-
included accessory : power supply, dust cover
-
Power consumption : 4,5 watts
-
dimensions : 420 x 112 x 330mm (WxHxD)
-
weight : 4,0 kg net
|
Reviews
There are no reviews yet.