Content | Fully Automatic Belt-Drive Stereo Turntable with Universal Tonearm & Headshell
- Fully Automatic Belt-Drive system
- Specially designed AT91R phono cartridge
- Removable universal AT-HS3 headshell
- Balanced straight tonearm
- Switchable MM & MC modes
- 33⅓ & 45 RPM selectable speeds
A revolution in automation, the LP3 blends outstanding analogue sound with advanced features unique to a fully-automatic belt-drive turntable. Play 33⅓ & 45 RPM records with a pre-mounted AT91R Dual Moving Magnet phono cartridge whilst the tonearm’s removable universal headshell and switchable cartridge mode allows listeners to experiment with moving magnet and moving coil cartridges. Complete with a built-in phono pre-amplifier, the LP3 represents the next level for vinyl lovers.
- Fully automatic belt-drive turntable operation with two speeds: 33-1/3, 45 RPM
- Balanced straight tonearm with hydraulically damped lift control and lockable rest
- Built-in switchable phono/line pre-amplifier with attached dual RCA output cable
- Switchable modes for moving magnet and moving coil cartridges
- AT91R Dual Moving Magnet™ phono cartridge and AT-HS3 universal headshell
- Anti-resonance, die-cast aluminium platter with 4.5 mm thick rubber mat
- Damped base construction for reduced low-frequency feedback colouration
Mm / Mc Cartridge Selector Switch
Switchable MM/MC mode allows the listener to use both Moving Magnet and Moving Coil cartridges on their LP3, allowing for greater sonic customisation – a unique feature not found on most turntables with a built-in phono preamplifier.
Cartridge & Stylus |
Model |
AT91R |
Type |
VM Dual Magnet |
Output Voltage |
3.5mV (mV at 1kHz, 5 cm/sec) |
Vertical Tracking Force Range |
1.5 to 2.5g (standard 2.0g) |
Stylus Construction |
0.6 mil bonded conical |
Cantilever |
Aluminium pipe |
Recommended Load Impedance |
47,000 ohms |
Weight |
5.0g |
Headshell |
Model |
AT-HS3 |
Weight |
11.1g |
Overhang Adjustment |
8mm |
Tone arm |
Type |
Static balanced straight shaped with soft damping control |
Effective Length |
221.5mm |
Overhang |
19mm |
Maximum Tracking Error Angle |
Less than 3° |
Stylus Pressure Adjustment Range |
1 to 4g |
Applicable Cartridge Weight |
14.5 to 20g |
Anti-skating Range |
0 - 3 g |
Turntable |
Type |
Fully Automatic, Belt-Drive |
Motor |
DC motor |
Speeds |
33-1/3 RPM, 45 RPM |
Turntable Platter |
Die-cast aluminium |
Wow and Flutter |
Less than 0.2% WRMS (33 1/3 RPM) at3kHz |
Signal-to-Noise Ratio |
> 60 dB |
Output Level |
“PHONO” (MM) 3.5mV nominal at 1kHz, 5cm/sec
"LINE” (MC) 220mV nominal at 1kHz, 5cm/sec |
Phono Pre-Amp Gain |
36dB nominal, RIAA equalised
56dB nominal, RIAA equalised |
Power Supply Requirements |
220 to 240 V / 50, 60 Hz |
Power Consumption |
2W |
Dimensions |
435 mm ×353 mm×128 mm (W×D×H) |
Weight |
5.2kg |
Accessories Included |
Rubber mat, Dust cover, Platter (with drive belt), Counterweight, AT-HS3 Headshell with AT91R VM stereo cartridge, 45 RPM adapter, Power cable |
|
A MUSICAL FAMILY
The TD 206 and TD 209 turntables are the younger siblings of the revolutionary, multiple-award-winning TD 309. However, they don’t have to live in the shadow of their older brother. Both models are built using only high-quality materials and parts. And both share a number of technical features with the TD 309, ensuring that their replay quality is up there with the best.
The new TP 90 tonearm is based on the tried-and-tested TP 92 and uses the same ultra-low-friction, high-performance bearing and the innovative zero-stiction anti-bias system. The arm tube is made from rolled aluminium that is damped using RMR technology (reduced-modal-resonance), and the stainless-steel counterweight at the end of the arm tube is double-decoupled. Tonearm height, azimuth and overhang are useradjustable.
SPECIAL FEATURES
- Low Noise, Low Voltage electronically speed controlled DC Motor
- Adjustable belt tension for best performance
- Two-part aluminium/acrylic platter
- New TP 90 tonearm with precision Japanese bearings
- Tonearm adjustable for VTA, azimuth and overhang
- Made in Germany
|
JB Systems Q3-USB features: - high torque direct drive motor
- fast start / stop
- 3 speeds: 33, 45, 78 rpm with quartz lock
- 2 pitch adjustment ranges: +/-10% ; +/-20%
- forward / reverse play
- starting torque: More than 1.6kgf / cm
- starting time: less than 1 second
- braking time: less than 1 second
- tracking error angle: less than 3°
- USB-output for direct recording to any PC
- free, multilingual Audacity software available via download:
- endless possibilities with free downloadable effect plug-ins
- import, export and edit Ogg Vorbis, MP3, AIFF and WAV sound files.
- cut, copy, splice, and mix sounds together.
- change the speed or pitch of a recording.
- remove static, hiss, hum, or other constant background noises.
- alter frequencies with Equalization, FFT Filter, and Bass Boost effects.
- adjust volumes with Compressor, Amplify, and Normalize effects.
- selectable phono/line output
- all functions are equipped with stylish, blue LED lights
- plastic dust cover
- retractable target light
- Audio Technica cartridge included
- all metal S-shaped tone arm assembly with: counterweight, anti-skating adjustment, lever lift with
- height adjustment
- adjustable large feet for perfect leveling
- phono output: 1,5~3,6mV
- line-output: 90~216mV
- PC interface: USB 1.1 compatible (Win XP/Vista/Win7 or Mac OS X)
- power supply: 230V
- power consumption: 11 watt
- dimensions: 450 x 352 x 157 mm
- weight: 10,5 kg
|
Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight ultra low mass tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it in.
The only plastic here is the stylus guard. The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
-
Belt drive system with low vibration DC motor
-
Central gravity mass point made from artificial stone
-
Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom
-
Low resonance MDF platter with felt mat
-
8,6” ultra low mass tonearm with straight arm tube
-
Pre-adjusted tracking force & antiskating
-
Gold-plated RCA contacts & cartridge pins
-
Colour options: red-black, white-black, silver-black
Specifications:
-
speed : 33, 45 (manual speed change)
-
Speed variance: 33: 0,2% 45: 0,18%
-
Wow & flutter: 33: 0,14% 45: 0,13%
-
platter: 300mm MDF
-
tonearm: 8,6” metal tube
-
effective arm length: 218,5 mm
-
overhang: 22,0 mm
-
effective tonearmmass: 8,0gr
-
counterweight for cartridge mass: 3 - 5,5g (included)
-
tracking force range: 0 - 30mn (OM5 18mn pre-adjusted)
-
output: RCA to phono input
-
included accessory: RCA cable, 15V DC power supply
-
power consumption: 4,0 watts
-
dimensions: 430 x 90 x 300mm (WxHxD)
-
weight: 2,7 kg net
|
Best buy turntable with maximum simplicity, outstanding sound quality & USB recording capability!
Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental Phono USB table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it into hifi system and computer.
The only plastic here is the stylus guard!
The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards and vinyl recording capability.
• Belt drive system • Integrated motor control with DC power supply secures silent running • Central gravity mass point made from artificial stone • Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom • Low resonance MDF platter with felt mat • 8,6” ultra low mass tonearm with straight arm tube • Pre-adjusted tracking force & antiskating • Gold-plated RCA contacts & cartridge pins • Integrated phono stage with precise RIAA equalisation • Line level output • A/D converter for vinyl recording with USB B output
• Colour options: red-black, white-black, silver-black
|
The first Debut turntable, introduced in the late 1990s, was a revolution for the hi-fi industry. For the first time after the arrival of Compact Disc and the assumed demise of vinyl records, an analogue product re-emerged in the "mass market” – something all music lovers could afford.
The new DEBUT Carbon DC has been designed to set new standards in this category for the coming decade – perfectly timed as analogue today is again a respected source, while the demand for good turntables is growing again!
The most obvious improvement is the inclusion of a CARBON TUBE for the tonearm, which increases stiffness and decreases unwanted resonance.
This material normally is extensively used in high-end tonearms, but – because of cost reasons – was never used in products at lower price levels. Together with other improvements like an increase in platter size and weight to realize even smoother rotation, the overall sound quality is greatly improved. The approved belt drive design offers low noise AC motor with effective motor decoupling (utilising TPE-damping) and ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability without unwanted vibration.
The DEBUT CARBON DC will be offered in high-gloss black or shiny red, green, blue, yellow, silver or white as no-added-cost option.
Specifications:
-
8,6” carbon tonearm
-
Increased platter size with more weight
-
Precision belt drive with synchronous motor
-
New DC power supply with ultra precision frequency DC-driven AC generator (like Speed Box) for ultimate speed stability.
-
New TPE motor suspension
-
Felt mat
-
magnetic cartridge options from Ortofon OM 10 or 2M red
-
7 high-gloss colours
|
Reviews
There are no reviews yet.