| Content | Fully Automatic Belt-Drive Stereo Turntable with Universal Tonearm & Headshell
- Fully Automatic Belt-Drive system
- Specially designed AT91R phono cartridge
- Removable universal AT-HS3 headshell
- Balanced straight tonearm
- Switchable MM & MC modes
- 33⅓ & 45 RPM selectable speeds
A revolution in automation, the LP3 blends outstanding analogue sound with advanced features unique to a fully-automatic belt-drive turntable. Play 33⅓ & 45 RPM records with a pre-mounted AT91R Dual Moving Magnet phono cartridge whilst the tonearm’s removable universal headshell and switchable cartridge mode allows listeners to experiment with moving magnet and moving coil cartridges. Complete with a built-in phono pre-amplifier, the LP3 represents the next level for vinyl lovers.
- Fully automatic belt-drive turntable operation with two speeds: 33-1/3, 45 RPM
- Balanced straight tonearm with hydraulically damped lift control and lockable rest
- Built-in switchable phono/line pre-amplifier with attached dual RCA output cable
- Switchable modes for moving magnet and moving coil cartridges
- AT91R Dual Moving Magnet™ phono cartridge and AT-HS3 universal headshell
- Anti-resonance, die-cast aluminium platter with 4.5 mm thick rubber mat
- Damped base construction for reduced low-frequency feedback colouration
Mm / Mc Cartridge Selector Switch
Switchable MM/MC mode allows the listener to use both Moving Magnet and Moving Coil cartridges on their LP3, allowing for greater sonic customisation – a unique feature not found on most turntables with a built-in phono preamplifier.
| Cartridge & Stylus |
| Model |
AT91R |
| Type |
VM Dual Magnet |
| Output Voltage |
3.5mV (mV at 1kHz, 5 cm/sec) |
| Vertical Tracking Force Range |
1.5 to 2.5g (standard 2.0g) |
| Stylus Construction |
0.6 mil bonded conical |
| Cantilever |
Aluminium pipe |
| Recommended Load Impedance |
47,000 ohms |
| Weight |
5.0g |
| Headshell |
| Model |
AT-HS3 |
| Weight |
11.1g |
| Overhang Adjustment |
8mm |
| Tone arm |
| Type |
Static balanced straight shaped with soft damping control |
| Effective Length |
221.5mm |
| Overhang |
19mm |
| Maximum Tracking Error Angle |
Less than 3° |
| Stylus Pressure Adjustment Range |
1 to 4g |
| Applicable Cartridge Weight |
14.5 to 20g |
| Anti-skating Range |
0 - 3 g |
| Turntable |
| Type |
Fully Automatic, Belt-Drive |
| Motor |
DC motor |
| Speeds |
33-1/3 RPM, 45 RPM |
| Turntable Platter |
Die-cast aluminium |
| Wow and Flutter |
Less than 0.2% WRMS (33 1/3 RPM) at3kHz |
| Signal-to-Noise Ratio |
> 60 dB |
| Output Level |
“PHONO” (MM) 3.5mV nominal at 1kHz, 5cm/sec
"LINE” (MC) 220mV nominal at 1kHz, 5cm/sec |
| Phono Pre-Amp Gain |
36dB nominal, RIAA equalised
56dB nominal, RIAA equalised |
| Power Supply Requirements |
220 to 240 V / 50, 60 Hz |
| Power Consumption |
2W |
| Dimensions |
435 mm ×353 mm×128 mm (W×D×H) |
| Weight |
5.2kg |
| Accessories Included |
Rubber mat, Dust cover, Platter (with drive belt), Counterweight, AT-HS3 Headshell with AT91R VM stereo cartridge, 45 RPM adapter, Power cable |
| Platter of diecast aluminum
Drive belt
Built-in phono equalizer controlled by switch (possible connection to an input-AUX)
Includes MM cartridge
elegant size
MANUAL/ΕΓΧΕΙΡΙΔΙΟ |
Best buy turntable with maximum simplicity, outstanding sound quality & USB recording capability!
Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental Phono USB table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it into hifi system and computer.
The only plastic here is the stylus guard!
The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards and vinyl recording capability.
• Belt drive system
• Integrated motor control with DC power supply secures silent running
• Central gravity mass point made from artificial stone
• Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom
• Low resonance MDF platter with felt mat
• 8,6” ultra low mass tonearm with straight arm tube
• Pre-adjusted tracking force & antiskating
• Gold-plated RCA contacts & cartridge pins
• Integrated phono stage with precise RIAA equalisation
• Line level output
• A/D converter for vinyl recording with USB B output
• Colour options: red-black, white-black, silver-black
|
Manual, Drive System belt-drive (flat belt around sub-platter), Speeds 33-1/3, 45 rpm, Tonearm THORENS TP 90, Pick-up Cartridge AT-95 B, Anti-skating (Bias) by magnet, Dimensions 470 x 125 x 430 mm (W x H x D), Weight 4.7 kg, power supply, RCA interconnects, stylus gauge, spirit level, cartridge alignment protractor | Pro-Ject has decided to go after the cheap plastic turntable market with an high quality alternative that comes complete with an Ortofon cartridge. The new Elemental table is a real "plug'n'play" all the way. No adjustment of counterweight and antiskating is needed, because both are pre-adjusted. This new straight ultra low mass tonearm is optimised for Ortofon OM cartridge series. All the buyer needs to do is remove it from the box, remove bearing guard, locate the belt around the platter, remove stylus guard and plug it in.
The only plastic here is the stylus guard. The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
The hidden secret to the new table's sonic success, is a central gravity mass point, made from artificial stone and placed directly underneath the platter bearing. It is capable to fully absorb unwanted rumble and motor vibration. This turntable appears to be pure simplicity itself, while maintaining high quality audio standards.
- Belt drive system with low vibration DC motor
- Central gravity mass point made from artificial stone
- Main platter bearing made from stainless steel runs in bronze bushing with Teflon bottom
- Low resonance MDF platter with felt mat
- 8,6” ultra low mass tonearm with straight arm tube
- Pre-adjusted tracking force & antiskating
- Gold-plated RCA contacts & cartridge pins
- Colour options: red-black, white-black, silver-black
Specifications:
- speed : 33, 45 (manual speed change)
- Speed variance: 33: 0,2% 45: 0,18%
- Wow & flutter: 33: 0,14% 45: 0,13%
- platter: 300mm MDF
- tonearm: 8,6” metal tube
- effective arm length: 218,5 mm
- overhang: 22,0 mm
- effective tonearmmass: 8,0gr
- counterweight for cartridge mass: 3 - 5,5g (included)
- tracking force range: 0 - 30mn (OM5 18mn pre-adjusted)
- output: RCA to phono input
- included accessory: RCA cable, 15V DC power supply
- power consumption: 4,0 watts
- dimensions: 430 x 90 x 300mm (WxHxD)
- weight: 2,7 kg net
| DENON DP-300F Belt-driven automatic turntable with cartridge
Fully automatic operation makes the DP-300F easy to use.
With the touch of a button, the tonearm swings over
and begins playing your record, returning to its original position when finished.
Details:
aluminum platter
built-in phono preamp
belt-drive system with DC servo motor
dynamic balance tonearm with universal mount
fully automatic operation
manual lifter mechanism
replaceable moving magnet cartridge included
removable dust cover
heavy base construction
minor assembly required
two speeds: 33-1/3 rpm & 45 rpm
wow & flutter 0.10%
weight: 6 kgs
dimensions:17-1/16“W x 4-13/16“H x 15“D |
Reviews
There are no reviews yet.