| Content | The PRO42\'s low-profile design assures inconspicuous appearance for surface-mount use in boardroom, school, government, house of worship and other installed applications. Designed for sound reinforcement, broadcasting and recording applications, the PRO42 brings crisp, intelligible audio reproduction to the podium, stage, conference table and beyond. With a wide-range condenser element and low-mass diaphragm for superior performance, the microphone is equipped with self-contained electronics, eliminating the need for external power modules.
Very low-profile design for minimum visibility
Wide-range condenser element with low-mass diaphragm for superior performance
Uniform polar pattern for maximum rejection of unwanted sounds
Rugged design and construction
25\' (7.6 m) cable permanently attached between microphone and XLRM-type connector
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
Frequency Response: 70-14,000 Hz
Open Circuit Sensitivity: -38 dB (12.5 mV) re 1V at 1 Pa
Impedance: 100 ohms
Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: 105 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 65 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 9-52V DC, 2 mA typical
Weight: 1.2 oz (35 g)
Dimensions: 1.44" (36.6 mm) maximum width, 2.14" (54.3 mm) maximum length, 0.61" (15.5 mm) height
Output Connector: 3-pin XLRM-type on cable
Cable: 25\' (7.6 m) long, permanently attached |
C 562 CM
Small, low-profile boundary layer microphone
Wide frequency range
High sensitivity
Ideal for inconspicuous installation in a room
Suited for surveillance or recording
The C 562 CM flush-mount boundary microphone uses the same transducer as the C 562 BL.
The C 562 CM has been designed specifically for permanent, "invisible" mounting in ceilings,
walls, tables, stage props, etc.
Owing to its high sensitivity, the C 562 CM is a perfect tool for surveillance or live recording
since a single microphone can cover an entire room. The supplied XLR phantom power adapter
connects to the microphone cable through a miniature connector so installation holes can be
smaller than the diameter of the phantom power adapter.
SPECIFICATIONS:
Polar pattern omnidirectional (hemispherical)
Frequency range 20 to 20,000 Hz
Sensitivity 25 mV/Pa (-32 dBV)
Max. SPL 130 dB (k=1 %)
Equivalent noise level 16 dB-A
Signal/noise ratio (A-weighted) 78 dB
Impedance 600 ohms
Recommended load impedance >2000 ohms
Supply voltage 9 to 52 V phantom power to DIN/IEC
Current consumption Connector 3-pin XLR
Cable 0.5 m (20 in.)
Finish matte nickel plated
Dimensions 20 dia. x 28 mm (0.8 dia. x 1.1 in.)
Net weight 30 g (1.1 oz.)
Shipping weight 195 g (76.9 oz.)
|
The white-finished version of the U851R, the phantom-powered U851RW features a PivotPoint® rotating output connector, UniSteep® filter and UniGuard® RFI-shielding technology. Offering outstanding speech intelligibility and transparent sound quality for surface-mount applications, the U851RW accepts interchangeable condenser elements - available for boundary microphones in cardioid, hypercardioid and omnidirectional polar patterns. With a heavy die-cast case and silicon foam bottom pads to minimize coupling of surface vibration to the microphone, the U851RW is equipped with self-contained electronics, eliminating the need for an external power module.
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Superior off-axis rejection for maximum gain before feedback
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Self-contained electronics eliminate need for external power module
- Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance finish for minimum visibility
- Available in two colors: black (U851R) and white (U851RW)
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 108 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 4 mA typical
- Switch: Flat, roll-off
- Weight: 9.2 oz (262 g)
- Dimensions: 4.25" (108.0 mm) long, 3.31" (84.0 mm) maximum width, 0.91" (23.0 mm) height
- Output Connector: TB3M-type
- Cable: 25.0' (7.6 m) long, 0.13" (3.2 mm) diameter, 2-conductor, shielded cable with TA3F and XLRM-type connectors
|
Offering outstanding Audio-Technica sound for surface-mount applications, the U851A features a PivotPoint® rotating output connector, UniSteep® filter and UniGuard® RFI-shielding technology. This battery- or phantom-powered condenser microphone accepts interchangeable condenser elements - available for boundary microphones in cardioid, hypercardioid and omnidirectional polar patterns. Its heavy die-cast case and silicon foam bottom pads minimize coupling of surface vibration to the microphone. With superior off-axis rejection and maximum gain-before-feedback, this professional microphone sets audio-quality standards in challenging acoustic environments.
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Superior off-axis rejection for maximum gain before feedback
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- UniSteep® filter provides a steep low-frequency attenuation to improve sound pickup without affecting voice quality
- Small-diameter UniPoint capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance black finish for minimum visibility
- Operates on battery or phantom power
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: Phantom: -40 dB (10.0 mV) re 1V at 1 Pa Battery: -41 dB (8.9 mV) re 1V at 1 Pa
- Impedance: Phantom: 200 ohms Battery: 270 ohms
- Maximum Input Sound Level: Phantom: 133 dB SPL, 1 kHz at 1% T.H.D. Battery: 123 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: Phantom: 111 dB,1 kHz at Max SPL Battery: 101 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 72 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 2 mA typical
- Battery Type: 1.5V AA/UM3
- Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
- Switch: Off, on-flat, on-roll-off
- Cable: 25.0' (7.6 m) long (permanently attached to microphone), 0.13" (3.2 mm) diameter, 2-conductor, shielded cable with TA3F-type connector
- Accessories: AT8531 power module; battery; soft protective pouch
|
The new Engineered Sound.
This low-profile omnidirectional condenser boundary microphone is designed for clear, highly intelligible sound reinforcement, professional recording and teleconferencing in table-, ceiling-, or panel-mount applications. The microphone is equipped with a self-contained power module with an XLRM-type output connector, eliminating the need for an external power module. The microphone offers unsurpassed immunity from radio frequency interference thanks to Audio-Technica's UniGuard® innovations. Protected by a rugged all-metal case with a two-layer steel mesh grille, the microphone has a 360º pickup angle, and is available in two colors: black (ES945) and white (ES945W).
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording and teleconferencing
- Low-profile element provides uniform omnidirectional polar pattern with 360º acceptance angle
- Mounts unobtrusively in table-tops, ceilings and wall panels
- Self-contained power module with XLRM-type output connector
- Rugged all-metal case with a two-layer steel mesh grille
- Isolators provide mechanical dampening of mounting-surface vibration
- Requires 11V to 52V DC phantom power
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Available in two colors: black (ES945) and white (ES945W)
- RoHS compliant-free from all substances specified in the EU directive on hazardous substances
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Omnidirectional
- Frequency Response: 40-18,000 Hz
- Open Circuit Sensitivity: -42 dB (7.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 142 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 112 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 64 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 2 mA typical
- Weight: 63 g (2.2 oz)
- Dimensions: 69.0 mm (2.72“) long, 28.0 mm (1.10“) diameter
- Output Connector: Integral 3-pin XLRM-type
|
The e 912 is a pre-polarized condenser boundary microphone with
half-cardioid pick-up pattern. Its acoustic properties have been
optimized for instruments, vocals and speech. The e 912 is an ideal
choice for pianos, theatre and opera productions, conference applications,
altars and lecterns.To optimally match the installation environment,
the e 912 is available in black or creme white.
Features
Frequency response and sensitivity optimized for picking up instruments,
vocals and speech
Unobtrusive, flat housing
Extremely rugged and step-resistant
Shock-absorbing rubber base
Mounting slots for table installation
Gold-plated XLR connector
Integrated pre-amp
Delivery Includes
e 912 Microphone
Pouch
User manual
Technical Data
Transducer principle (Microphone) permanently polarized condenser
Pick-up pattern half-cardioid
Sensitivity in free field, no load (1kHz) 10 mV/Pa
Max. Sound pressure level (aktiv) 135,6 dB
Equivalent noise level 26 dB(A)
Phantom powering 48 V / 1,1 mA
Nominal impedance
Min. terminating impedance 1000 Ohm
Dimensions 126,5 x 105 x 26,5 mm
Weight ca. 550 g
|
Reviews
There are no reviews yet.