| Content | The PRO42\'s low-profile design assures inconspicuous appearance for surface-mount use in boardroom, school, government, house of worship and other installed applications. Designed for sound reinforcement, broadcasting and recording applications, the PRO42 brings crisp, intelligible audio reproduction to the podium, stage, conference table and beyond. With a wide-range condenser element and low-mass diaphragm for superior performance, the microphone is equipped with self-contained electronics, eliminating the need for external power modules.
Very low-profile design for minimum visibility
Wide-range condenser element with low-mass diaphragm for superior performance
Uniform polar pattern for maximum rejection of unwanted sounds
Rugged design and construction
25\' (7.6 m) cable permanently attached between microphone and XLRM-type connector
Element: Fixed-charge back plate, permanently polarized condenser
Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
Frequency Response: 70-14,000 Hz
Open Circuit Sensitivity: -38 dB (12.5 mV) re 1V at 1 Pa
Impedance: 100 ohms
Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
Dynamic Range: 105 dB, 1 kHz at Max SPL
Signal to Noise Ratio: 65 dB, 1 kHz at 1 Pa
Phantom Power Requiremens: 9-52V DC, 2 mA typical
Weight: 1.2 oz (35 g)
Dimensions: 1.44" (36.6 mm) maximum width, 2.14" (54.3 mm) maximum length, 0.61" (15.5 mm) height
Output Connector: 3-pin XLRM-type on cable
Cable: 25\' (7.6 m) long, permanently attached |
Designed for Broadcast, House of Worship, Pro Music, and other applications.
Half-cardioid polar pattern
Boundary layer
Ultra-thin profile (16 mm) housing
Rubber non-slip bottom pad and strong steel screen
Integrated pop filter
Case Material Die cast zinc
Connector Type 3-pin XLR
Element Back Electret Condenser
Finish Non-reflecting Black
Finish White
Impedance, Low-Z balanced 200 Ω
Mic Type Boundary
Open Circuit Voltage 25 mV/Pascal
Polar Pattern Cardioid
Wired/Wireless Wired
Height 16 mm (0.63“)
Width 94 mm (3.7“)
Depth 123 mm (4.84“)
Weight Net 12.63 oz (358 g) |
With three cardioid condenser elements in a single housing, the phantom-powered U843R offers a remarkably versatile tool for surface-mount installations. Levers on the microphone base allow easy reorientation of two elements to offer 360° or 300° coverage. Since elements can be powered and used individually or in any combination, further flexibility is easily achieved. For example, with two elements powered, the microphone can provide a figure-of-eight polar pattern; with a single element powered, the microphone functions as a standard cardioid boundary microphone. Installation and repositioning are extremely quick, thanks to four recessed pathways on the base of the microphone that enable the user to route the cable as required to accommodate any installation requirements; no tools or disassembly are needed. The microphone also offers Audio-Technicaʼs innovative UniGuard® RFI-shielding technology.
- Three cardioid condenser elements mounted in a single housing
- Easily reposition two elements (via levers on the microphone base) to offer 360° or 300° coverage; each element can be powered and used individually or in any combination
- Also functions as a stereo boundary microphone
- Provides full, efficient and flexible coverage—fewer microphones required
- Small-diameter capsules near boundary eliminate phase distortion and deliver clear, high-output performance
- Low-frequency attenuation improves sound pickup without affecting voice quality
- Cable routes through any of four recessed pathways on the microphone base (or down for direct feed through a table surface); no tools or disassembly required
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Heavy die-cast case and non-slip silicone foam bottom pad minimizes coupling of surface vibration to the microphone
- Low-profile design with low-reflectance finish for minimum visibility
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Hemispherical Cardioid x3 (combine to omni-directional or bidirectional)
- Frequency Response: 70-16,000 Hz
- Open Circuit Sensitivity: –37 dB (14.1 mV) re 1V at 1 Pa
- Impedance: 100 ohms
- Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range (Typical): 105 dB, 1 kHz at Max SPL
- Signal-to-Noise Ratio: 65 dB, 1 kHz at 1 Pa
- Phantom Power Requirements: 11-52V DC, 2 mA typical
- Switch: The lever of elements can adjust the proper position
- Weight (Less Cable): 160 g
- Dimensions: 20.0 mm - height
85.0 mm – maximum body diameter - Cable: 7.6 m long (permanently attached to microphone), 4 mm diameter, 6 conductor, shielded cable; output end stripped and tinned for connection to electronic device
- Accessories Furnished: Soft protective pouch
|
Condenser
Lightweight, sensitive diaphragm. Precisely and smoothly captures sound nuances. Powered by battery or phantom power supply.
Recommended Uses
Conference/Installed
The Microflex® Wireless Boundary Microphone offers total freedom of placement with no holes to drill or cables to run for installation.
The Wireless Boundary Microphone is the perfect solution for conference and meeting spaces where users demand flexibility and high performance. Compatible with Shure SLX® Wireless Systems.
|
Featuring breakthrough audio and mechanical design innovations, the phantom-powered U851R offers outstanding speech intelligibility and transparent sound quality for surface-mount applications. The microphone is equipped with a PivotPoint® rotating output connector, UniSteep® filter and UniGuard® RFI-shielding technology. It accepts interchangeable condenser elements - available for boundary microphones in cardioid, hypercardioid and omnidirectional polar patterns. With a heavy die-cast case and silicon foam bottom pads to minimize coupling of surface vibration to the microphone, the U851R is equipped with self-contained electronics, eliminating the need for an external power module.
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Superior off-axis rejection for maximum gain before feedback
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Self-contained electronics eliminate need for external power module
- Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance finish for minimum visibility
- Available in two colors: black (U851R) and white (U851RW)
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 108 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 4 mA typical
- Switch: Flat, roll-off
- Weight: 9.2 oz (262 g)
- Dimensions: 4.25" (108.0 mm) long, 3.31" (84.0 mm) maximum width, 0.91" (23.0 mm) height
- Output Connector: TB3M-type
- Cable: 25.0' (7.6 m) long, 0.13" (3.2 mm) diameter, 2-conductor, shielded cable with TA3F and XLRM-type connectors
|
The white-finished version of the U851R, the phantom-powered U851RW features a PivotPoint® rotating output connector, UniSteep® filter and UniGuard® RFI-shielding technology. Offering outstanding speech intelligibility and transparent sound quality for surface-mount applications, the U851RW accepts interchangeable condenser elements - available for boundary microphones in cardioid, hypercardioid and omnidirectional polar patterns. With a heavy die-cast case and silicon foam bottom pads to minimize coupling of surface vibration to the microphone, the U851RW is equipped with self-contained electronics, eliminating the need for an external power module.
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Superior off-axis rejection for maximum gain before feedback
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Self-contained electronics eliminate need for external power module
- Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance finish for minimum visibility
- Available in two colors: black (U851R) and white (U851RW)
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 108 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 4 mA typical
- Switch: Flat, roll-off
- Weight: 9.2 oz (262 g)
- Dimensions: 4.25" (108.0 mm) long, 3.31" (84.0 mm) maximum width, 0.91" (23.0 mm) height
- Output Connector: TB3M-type
- Cable: 25.0' (7.6 m) long, 0.13" (3.2 mm) diameter, 2-conductor, shielded cable with TA3F and XLRM-type connectors
|
Reviews
There are no reviews yet.