Content |
With its half-space unidirectional polar pattern, low-profile design, and outstanding sound quality, the PRO44 is ideal for conference tables, podiums, lecterns and other installed-sound uses. This versatile boundary mic\'s self-contained electronics eliminate the need for external power modules. The PRO44 is equipped with a wide-range condenser element with low-mass diaphragm for superior performance. Low profile for minimum visibility Wide-range condenser element with low-mass diaphragm for superior performance Self-contained electronics eliminate need for external power modules Rugged design and construction 25\' (7.6 m) detachable cable (TA3F to XLRM-type) Element: Fixed-charge back plate, permanently polarized condenser Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface) Frequency Response: 70-16,000 Hz Open Circuit Sensitivity: -25 dB (56.2 mV) re 1V at 1 Pa Impedance: 100 ohms Maximum Input Sound Level: 114 dB SPL, 1 kHz at 1% T.H.D. Dynamic Range: 86 dB, 1 kHz at Max SPL Signal to Noise Ratio: 66 dB, 1 kHz at 1 Pa Phantom Power Requiremens: 9-52V, 2 mA typical Weight: 2.4 oz (67 g) Dimensions: 2.87" (73.0 mm) maximum width, 3.56" (90.5 mm) maximum length, 0.59" (15.0 mm) height Output Connector: TB3M-type Cable: 25\' (7.6 m) long, with TA3F and XLRM-type connectors |
The half-cardioid e 901 is the perfect condenser microphone for kick drum. It is highly robust and step-resistant. It benefits from an integrated preamp.
Pick-up pattern : half-cardioid
Frequency response : 20...20 000 Hz
Sensitivity in free field, no load : (1kHz) 0,5 mV/Pa
Max. Sound pressure level (aktiv) : 154 dB / SPL
Phantom powering : 48 V / 1,1 mA
Nominal impedance :
Min. terminating impedance : 1000 Ohm
Dimensions : 126,5 x 105 x 26,5 mm
Weight : ca. 550 g
|
Type of Transmitter UHF Frequency Agile
Input Connector Internal fitting for interchangeable capsules
Type of Microphone Electret Condenser Boundary Microphone
Polar Pattern Cardioid (Supplied)
Interchangeable Mic Heads Yes - R183B Omnidirectional, R184B Supercardioid and R185B Cardioid cartridges available
Frequency Response 50Hz to 17kHz
Battery Type/Approx. Life 9 Volt Alkaline - 7 hours based on alkaline battery
# Of Channels Over 100 channels between 692-862MHz, depending on locale
Mute Switch Programmable Touch-Sensitive Switch
Level Control Gain Adjustment Range: -6 to 34dBs
Antenna Type Internal
Display Microphone Status & Battery Life LEDs
Dimensions 3.625 x 1.8 x 5.17 (92 x 46 x 131mm) (WxHxD)
|
Offering outstanding Audio-Technica sound for surface-mount applications, the U851A features a PivotPoint® rotating output connector, UniSteep® filter and UniGuard® RFI-shielding technology. This battery- or phantom-powered condenser microphone accepts interchangeable condenser elements - available for boundary microphones in cardioid, hypercardioid and omnidirectional polar patterns. Its heavy die-cast case and silicon foam bottom pads minimize coupling of surface vibration to the microphone. With superior off-axis rejection and maximum gain-before-feedback, this professional microphone sets audio-quality standards in challenging acoustic environments.
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Superior off-axis rejection for maximum gain before feedback
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- UniSteep® filter provides a steep low-frequency attenuation to improve sound pickup without affecting voice quality
- Small-diameter UniPoint capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance black finish for minimum visibility
- Operates on battery or phantom power
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: Phantom: -40 dB (10.0 mV) re 1V at 1 Pa Battery: -41 dB (8.9 mV) re 1V at 1 Pa
- Impedance: Phantom: 200 ohms Battery: 270 ohms
- Maximum Input Sound Level: Phantom: 133 dB SPL, 1 kHz at 1% T.H.D. Battery: 123 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: Phantom: 111 dB,1 kHz at Max SPL Battery: 101 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 72 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 2 mA typical
- Battery Type: 1.5V AA/UM3
- Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
- Switch: Off, on-flat, on-roll-off
- Cable: 25.0' (7.6 m) long (permanently attached to microphone), 0.13" (3.2 mm) diameter, 2-conductor, shielded cable with TA3F-type connector
- Accessories: AT8531 power module; battery; soft protective pouch
|
C 547 BL
"Non-crush" case
Inconspicuous
Hypercardioid polar pattern
Easy to repaint
Hypercardioid, studio-quality boundary microphone with rugged, "non-crush" case and
switchable bass-cut filter for reducing footfall noise, ideal for tough on-stage assignments.
Other benefits include optimum acoustic properties, high directivity, and neutral sound.
Having the same frequency response, the C 547 BL can be combined with the CK 47 with
excellent results.
Primarily designed for use in places of worship, theaters, and conferencing, the C 547 BL
is also a good choice for miking kick drums and other instruments.
SPECIFICATIONS:
Polar pattern hypercardioid
Frequency range 30 to 18,000 Hz
Sensitivity 8.5 mV/Pa (-42 dBV)
Max. SPL 133 dB (for 1% THD)
Equivalent noise level 22 dB-A
Signal/noise ratio (A-weighted) 72 dB
Bass filter 12 dB/octave at 150 Hz
Impedance 400 ohms
Recommended load impedance >1000 ohms
Supply voltage 9 to 52 V phantom power to DIN 45596
Current consumption |
Designed for Broadcast, House of Worship, Pro Music, and other applications. Half-cardioid polar pattern Boundary layer Ultra-thin profile (16 mm) housing Rubber non-slip bottom pad and strong steel screen Integrated pop filter Case Material Die cast zinc Connector Type 3-pin XLR Element Back Electret Condenser Finish Non-reflecting Black Finish White Impedance, Low-Z balanced 200 Ω Mic Type Boundary Open Circuit Voltage 25 mV/Pascal Polar Pattern Cardioid Wired/Wireless Wired Height 16 mm (0.63“) Width 94 mm (3.7“) Depth 123 mm (4.84“) Weight Net 12.63 oz (358 g) |
Reviews
There are no reviews yet.