Content |
The M3R belt pack receiver is part of the M3 system. Rugged, ergonomic compensate housing includes a field-replaceable flexible-whip antennas. Digital LCD display with soft touch controls. The stereo monitor system offers Personal Mix Control, which gives each musician volume and mix control of two independent signals on stage, via easy-to-use controls on the M2R stereo body-pack receiver. Any number of M2R stereo receivers may be used on the same frequency with a single M2T stereo transmitter. On board 3 level limiter (defeatable) helps protect your hearing from sudden peaks. Includes Audio-Technica earphones with proprietary dynamic drivers offer full frequency response and outstanding isolation with 3 sizes of rubber eartips plus an ear-conforming foam tip. Also, an auxiliary input offers a connection point for an ambient microphone, click track, or other mic- or line-level input.
These rugged systems are built to stand up to the inevitable bumps of life on the road, delivering clear, natural sound for touring and installed-sound uses.
- Receiving System: Double conversion superheterodyne
- RF Sensitivity: 20 dBuV (at 60 dB S/N ratio, 50 ohms termination)
- Headphone Output Connector: 3.5 mm TRS stereo phone jack
- Headphones Output Power: 65 mW (at 32 ohms)
- Antenna Input: SMA-type, 50 ohms
- Aux. Input Connector: 3.5 mm TRS stereo phone jack
- Batteries: 2 x 1.5V AA (not included)
- Battery Life: 8 hours (alkaline) Depending on battery type and use pattern
- Dimensions: 70.0 mm (2.76“) W x 25.0 mm (0.98“) D x 110.0 mm (4.33“) H
- Net Weight: 133 g (4.7 oz), without batteries
- Accessories Included: EP3 earphone; flexible antenna
|
- Three selectable UHF frequencies for interference-free reception.
- Diversity: maximum transmission reliability even in difficult environments. The system automatically selects the antenna providing the best signal.
- Adjustable squelch
- Multichannel capability for simultaneous use of up to nine channels (maximum number of channel depends on local frequency plans).
- All-metal case
- High Definition Audio Performance technology ensures the legendary, realistic AKG sound and perfect audio transmission.
|
Compatible with the Wireless Essentials® range. Rugged, ergonomic metal housing. Includes field-replaceable helical and flexible-whip antennas. Three-position sliding cover limits access to controls as desired: full access, Power/Mute button only, or no access. Two position mounting clip. For use with AEW-T1000a and all Audio-Technica UniPak™ Wireless Transmitters.
The AEW-T1000a wireless UniPak® body-pack transmitter has both low and high impedance inputs plus a DC bias connection allowing it to be used with both condenser and dynamic microphones. The locking 4-pin HRS-type audio input connector is recessed to protect the connection from damage. A dual-colour power/mute indicator LED provides visual indication of transmitter status. The transmitter operates using two standard AA batteries and features high- and low-level RF output settings. The low-level setting allows two additional hours of battery life while retaining a strong RF signal link. Soft-touch controls provide convenient access to a variety of functions including: RF power, audio input level, power/mute locks and frequency selection. Each transmitterʼs backlit LCD display presents a great deal of setup and operating information clearly and conveniently, including battery level remaining, mute, and operating frequency. A flashing "Lo-Batt” alert visually signals the battery life is almost depleted. Programmable power/mute locks limit the functioning of transmitterʼs power/mute button as desired for particular users and applications. Four nameable user presets allow for storage and recall of commonly used settings. To match the audio input level to the transmitter, a ten-position audio input gain setting selected through the function menu is provided. The body-pack features a safety cover to protect the soft-touch controls from being accidently activated and a recessed input connector to increase the life of the microphone cable. Inputs are available on the UniPak® for low impedance microphone and high impedance musical instrument or line input. Constructed of metal, the body-pack transmitter features a field replaceable antenna, captive locking battery cover door, a short rigid helical antenna and a flexible wire antenna.
- Available in the following frequency bands:
541.500 - 566.375 MHz (C Band)
655.500 - 680.375 MHz (D Band)
721.500 - 746.375 MHz (G Band) - 25 kHz frequency spacing makes it easier to find a clear, open
- frequency in crowded RF environments
- Dual RF power output selection to optimize battery life
- Digital Tone Lock™ squelch that communicates transmitter data
- to the receiver
- Function menu displayed in a backlit LCD window, controlled by
- internal soft-touch controls
- High efficiency dual companding system for flawless audio
- Four nameable user presets
- Battery fuel gauge on LCD readout
- Recessed microphone input connector
- Power/mute lock provision as well as safety door to cover controls
- Dual-colour power/mute status indictor
- Microphone or line input with DC bias voltage
- 18 dB audio input level adjustment
- Operates on two AA batteries
- Captive locking battery compartment door
- Adjustable squelch
- Rugged metal housing with a reversible clothing clip
- RF Power Output: High: 35 mW; Low: 10 mW, nominal
- Spurious Emissions: According to National Regulations
- Microphone Dynamic Range: >=110 dB, A-weighted
- Instrument Dynamic Range: >=110 dB, A-weighted
- Input Connections: High impedance, low impedance, bias
- Batteries: Two 1.5V AA alkaline (not included)
- Battery Life: Approximately 8 hours (High); 10 hours (Low), depending on battery type and use pattern
- Dimensions: 66.0mm W x 87mm H x 24mm; not including antenna
- Net Weight: 125 g
|
The wireless tuner WT-5800 is a PLL-synthesizer controlled double superheterodyne true diversity tuner to be used in UHF wireless systems. It employs a compander noise reduction circuit to minimize the influence of the ambient RF noise.
(*1) 0 dB = 1 V Power Source | AC mains (supplied AC adapter must be used) | Power Consumption | 250 mA (12 V DC) | Receiving Frequency | 636 - 865 MHz(*2), UHF | Channel Selectable | 64 selectable frequencies | Receiving System | Double super-heterodyne | Diversity System | Space diversity (true diversity) | Mixing Output | MIC: -60 dB(*1), 600 Ω, balanced, XLR-3-32 type connector
LINE: -20 dB(*1), 600 Ω, unbalanced, phone jack | Mixing Input | -20 dB(*1), 10 kΩ, unbalanced, phone jack | Antenna Input | 75 Ω, BNC (phantom powering for antenna), 9 V DC, 30 mA (max) | Antenna Output | 75 Ω, BNC (Gain 0 dB) | Receiving Sensitivity | 90 dB or more, S/N ratio (20 dBμV input, 40 kHz deviation) | Squelch Sensitivity | 18 - 40 dBμV variable | Squelch System | Using together of noise SQ, carrier SQ and tone SQ | Tone Frequency | 32.768 kHz | Indicator | Audio (6 step), RF (6 step), ANT A/B, Audio (peak), Battery alarm | Channel Check | Usable frequencies scanning | S/N Ratio | 110 dB or more (A-weight, unbalanced output) | Harmonic Distortion | 1 % or less (typical) | Frequency Response | 100 Hz - 15 kHz, ±3 dB | Operating Temperature | -10 ℃ to +50 ℃ | Finish | Resin, black | Dimensions | 210 (W) × 44 (H) × 205.1 (D) mm | Weight | 700 g | Accessory | AC adapter(*3) …1, Wireless antenna …2 | Option | Mounting bracket kit: MB-WT3 (for rack mounting one WT-5800 unit)
MB-WT4 (for rack mounting two WT-5800 units) |
|
It is nice when you can concentrate fully on the picture because you know the sound is reliable. This camera receiver allows you to do just that. Equipped with adaptive diversity, the camera receiver ensures reliable reception. Five frequency ranges with up to 75 MHz switching bandwidth also provide optimum flexibility for components of the 2000 series. The transmitter settings can be synchronized quickly from EK 2000 using infrared technology. |
The ATW-T310b wireless UniPak® body-pack transmitter has both low and high impedance inputs plus a 5V DC bian connection allowing it to be used with condenser and dynamic microphones, as well as Hi-Z instrument pickups. The locking 4-pin HRS-type audio input connector is recessed to protect the connection from damage. Operating on two standard AA batteries, the transmitter features high and low-level RF output settings. The low-level setting allows two additional hours of bttery life while retaining a strong RF signal link. Soft-touch controls provide convenient access to a variety of functions including: RF power, audio input level, power/mute locks and frequency selection. Each transmitterʼs backlit LCD display presents a great deal of setup and operating information clearly and conveniently including battery fuel remaining, mute, and operating frequency. A flashing "Lo-Batt” alert visually signals the battery life is almost depleted. A dual-colour status LED illuminates green when power is on, and red when the transmitter is muted. Programmable power/mute locks limit the functioning of the transmitterʼs power/mute button as desired for particular users and applications. To match the audio input level to the transmitter, a four-position audio input gain setting selected through the function menu is provided.
The body-pack transmitter features a safety cover to protect the soft-touch controls from being accidentally activated and a recessed input connector to increase the life of the microphone cable. Constructed of high impact materials, the body-pack transmitter features a field replaceable whip antenna and captive locking battery cover door.
- RF Power Output: High: 30 mW, Low: 10 mW (switchable), at 50 ohms
- Spurious Emissions: Following federal and national regulations
- Input Connection: Four-pin Locking Connector
Pin 1: GND, Pin 2: INST INPUT,
Pin 3: MIC INPUT, Pin 4: DC BIAS +5V - Batteries: Two 1.5V AA, not included
- Battery Life: High: 6 hours (alkaline), Low: 8 hours (alkaline)
Depending on battery type and use pattern. - Dimensions: 66.0 mm W x 24.0 mm D x 87.0 mm H
- Net Weight: 81 g without batteries
|
Reviews
There are no reviews yet.