Content |
With three cardioid condenser elements in a single housing, the phantom-powered U843R offers a remarkably versatile tool for surface-mount installations. Levers on the microphone base allow easy reorientation of two elements to offer 360° or 300° coverage. Since elements can be powered and used individually or in any combination, further flexibility is easily achieved. For example, with two elements powered, the microphone can provide a figure-of-eight polar pattern; with a single element powered, the microphone functions as a standard cardioid boundary microphone. Installation and repositioning are extremely quick, thanks to four recessed pathways on the base of the microphone that enable the user to route the cable as required to accommodate any installation requirements; no tools or disassembly are needed. The microphone also offers Audio-Technicaʼs innovative UniGuard® RFI-shielding technology.
- Three cardioid condenser elements mounted in a single housing
- Easily reposition two elements (via levers on the microphone base) to offer 360° or 300° coverage; each element can be powered and used individually or in any combination
- Also functions as a stereo boundary microphone
- Provides full, efficient and flexible coverage—fewer microphones required
- Small-diameter capsules near boundary eliminate phase distortion and deliver clear, high-output performance
- Low-frequency attenuation improves sound pickup without affecting voice quality
- Cable routes through any of four recessed pathways on the microphone base (or down for direct feed through a table surface); no tools or disassembly required
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Heavy die-cast case and non-slip silicone foam bottom pad minimizes coupling of surface vibration to the microphone
- Low-profile design with low-reflectance finish for minimum visibility
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Hemispherical Cardioid x3 (combine to omni-directional or bidirectional)
- Frequency Response: 70-16,000 Hz
- Open Circuit Sensitivity: –37 dB (14.1 mV) re 1V at 1 Pa
- Impedance: 100 ohms
- Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range (Typical): 105 dB, 1 kHz at Max SPL
- Signal-to-Noise Ratio: 65 dB, 1 kHz at 1 Pa
- Phantom Power Requirements: 11-52V DC, 2 mA typical
- Switch: The lever of elements can adjust the proper position
- Weight (Less Cable): 160 g
- Dimensions: 20.0 mm - height
85.0 mm – maximum body diameter - Cable: 7.6 m long (permanently attached to microphone), 4 mm diameter, 6 conductor, shielded cable; output end stripped and tinned for connection to electronic device
- Accessories Furnished: Soft protective pouch
| About the AKG Acoustics CBL 410 PCC
The AKG CBL 410 PCC Conference Microphone Set (Black) is a simple to use, plug and play desktop microphone for use with any PC or laptop. It improves audio quality incredibly when making a conference via VOIP. The microphone reproduces the voice with a clear and natural sound.
With its 3.5 mm stereo jack, it is a 100% plug and play device. No drivers are needed. Its ability to be cascaded makes the CBL 410 PCC the perfect tool for modern communication for both single person use in the office and/or multi-person use in a modern meeting room.
This microphone provides optimum intelligibility and audio quality for your meetings. The CBL 410 PCC is also an excellent choice for recording applications.
AKG Acoustics CBL 410 PCC Includes
- AKG 3x CBL 410 PCC PC Boundary Layer Microphones
- GHAP1 USB Adapter
- AKG Warranty
AKG Acoustics CBL 410 PCC Features
- Small and inconspicuous
- Exceptionally rugged
- Excellent sound quality
- High sensitivity
- Low self-noise
AKG Acoustics CBL 410 PCC Specifications
Polar pattern |
Omnidirectional |
Microphone Type |
Back electret condenser microphone |
Frequency response |
50 Hz to 20 kHz |
Impedance |
2000 ohms ±30% at 1000 Hz |
Sensitivity |
-42 dB ±3 dB (7.9 mV/Pa)Sensitivity: |
Maximum current consumption |
0.5 mA |
Supply voltage |
1.5 to 5 V DC |
Cable length |
100cm (40“) |
Connector |
TRS mini jack |
|
Designed to deliver easy, flexible control in conference and boardroom installations, the versatile U891Rx cardioid condenser boundary microphone features a touch-sensitive on-off switch that can be set to three modes: press-on/press-off, press to talk, and press to mute. The phantom-powered microphone is equipped with a unique PivotPoint® rotating output connector and an LED status indicator. UniGuard® innovations offer unsurpassed immunity from radio frequency interference; interchangeable elements are available in cardioid, hypercardioid and omnidirectional polar patterns; an 80 Hz low-cut UniSteep® filter reduces pickup of low-frequency ambient noise. The microphone's heavy die-cast case and silicon foam bottom pads minimize coupling of surface vibration to the microphone. The unit's self-contained electronics eliminate the need for an external power module.
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 130 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 104 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
- Phantom Power Requirements: 11-52V DC, 4 mA typical
- Weight: 264 g
- Dimensions: 108.0 mm long, 84.0 mm maximum width, 23.0 mm height
- Output Connector: TB3M-type
- Cable: 7.6 m long, 3.2 mm diameter, 2-conductor, shielded cable with TA3F and XLRM-type connectors
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
- Ultra-quiet electronic switch can be set to any of three operating modes: "touch-on/ touch-off," "touch-to-talk" and "touch-to-mute“
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Superior off-axis rejection for maximum gain before feedback
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance finish for minimum visibility
- Available in two colors: black (U891Rx) and white (U891RWx)
|
Condenser
Lightweight, sensitive diaphragm. Precisely and smoothly captures sound nuances. Powered by battery or phantom power supply.
Recommended Uses
Conference/Installed
The Microflex® Wireless Boundary Microphone offers total freedom of placement with no holes to drill or cables to run for installation.
The Wireless Boundary Microphone is the perfect solution for conference and meeting spaces where users demand flexibility and high performance. Compatible with Shure SLX® Wireless Systems.
|
The U841A delivers exceptionally intelligible audio reproduction in a super-compact, low-profile design. Equipped with UniGuard® RFI-shielding technology, this omnidirectional condenser boundary microphone is designed for clear, highly intelligible sound reinforcement, professional recording, television and conferencing in surface-mount applications. The U841A has a 360° pickup angle and operates on battery or phantom power.
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- UniSteep® filter provides a steep low-frequency attenuation to improve sound pickup without affecting voice quality
- Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- Heavy die-cast case and silicon foam bottom pad minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance black finish for minimum visibility
- Operates on battery or phantom power
- Element: Fixed-charge back plate permanently polarized condenser
- Polar Pattern: Omnidirectional in hemisphere above mounting surface
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: Phantom: -39 dB (11.2 mV) re 1V at 1 Pa Battery: -40 dB (10.0 mV) re 1V at 1 Pa
- Impedance: Phantom: 200 ohms Battery: 270 ohms
- Maximum Input Sound Level: Phantom: 132 dB, 1 kHz at 1% T.H.D. Battery: 122 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: Phantom: 111 dB, 1 kHz at Max SPL Battery: 101 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 73 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 2 mA typical
- Battery Type: 1.5V AA/UM3
- Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
- Switch: Off, on-flat, on-roll-off
- Cable: 25.0' (7.6 m) long (permanently attached to microphone), 0.13" (3.2 mm) diameter, 2-conductor, shielded cable with TA3F-type connector
- Accessories: AT8531 power module; battery; soft protective pouch
|
With its half-space unidirectional polar pattern, low-profile design, and outstanding sound quality, the PRO44 is ideal for conference tables, podiums, lecterns and other installed-sound uses. This versatile boundary mic\'s self-contained electronics eliminate the need for external power modules. The PRO44 is equipped with a wide-range condenser element with low-mass diaphragm for superior performance. Low profile for minimum visibility Wide-range condenser element with low-mass diaphragm for superior performance Self-contained electronics eliminate need for external power modules Rugged design and construction 25\' (7.6 m) detachable cable (TA3F to XLRM-type) Element: Fixed-charge back plate, permanently polarized condenser Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface) Frequency Response: 70-16,000 Hz Open Circuit Sensitivity: -25 dB (56.2 mV) re 1V at 1 Pa Impedance: 100 ohms Maximum Input Sound Level: 114 dB SPL, 1 kHz at 1% T.H.D. Dynamic Range: 86 dB, 1 kHz at Max SPL Signal to Noise Ratio: 66 dB, 1 kHz at 1 Pa Phantom Power Requiremens: 9-52V, 2 mA typical Weight: 2.4 oz (67 g) Dimensions: 2.87" (73.0 mm) maximum width, 3.56" (90.5 mm) maximum length, 0.59" (15.0 mm) height Output Connector: TB3M-type Cable: 25\' (7.6 m) long, with TA3F and XLRM-type connectors |
Reviews
There are no reviews yet.