Audio Technica U843R Three channel boundary cardioid condenser microphone

With three cardioid condenser elements in a single housing, the phantom-powered U843R offers a remarkably versatile tool for surface-mount installations. Levers on the microphone base allow easy reorientation of two elements to offer 360° or 300° coverage. Since elements can be powered and used individually or in any combination, further flexibility is easily achieved. For example, with two elements powered, the microphone can provide a figure-of-eight polar pattern; with a single element powered, the microphone functions as a standard cardioid boundary microphone. Installation and repositioning are extremely quick, thanks to four recessed pathways on the base of the microphone that enable the user to route the cable as required to accommodate any installation requirements; no tools or disassembly are needed. The microphone also offers Audio-Technicaʼs innovative UniGuard® RFI-shielding technology.

• Three cardioid condenser elements mounted in a single housing
• Easily reposition two elements (via levers on the microphone base) to offer 360° or 300° coverage; each element can be powered and used individually or in any combination
• Also functions as a stereo boundary microphone
• Provides full, efficient and flexible coverage—fewer microphones required
• Small-diameter capsules near boundary eliminate phase distortion and deliver clear, high-output performance
• Low-frequency attenuation improves sound pickup without affecting voice quality
• Cable routes through any of four recessed pathways on the microphone base (or down for direct feed through a table surface); no tools or disassembly required
• UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
• Heavy die-cast case and non-slip silicone foam bottom pad minimizes coupling of surface vibration to the microphone
• Low-profile design with low-reflectance finish for minimum visibility

• Element: Fixed-charge back plate, permanently polarized condenser
• Polar Pattern: Hemispherical Cardioid x3 (combine to omni-directional or bidirectional)
• Frequency Response: 70-16,000 Hz
• Open Circuit Sensitivity: –37 dB (14.1 mV) re 1V at 1 Pa
• Impedance: 100 ohms
• Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
• Dynamic Range (Typical): 105 dB, 1 kHz at Max SPL
• Signal-to-Noise Ratio: 65 dB, 1 kHz at 1 Pa
• Phantom Power Requirements: 11-52V DC, 2 mA typical
• Switch: The lever of elements can adjust the proper position
• Weight (Less Cable): 160 g
• Dimensions: 20.0 mm - height
  85.0 mm – maximum body diameter
• Cable: 7.6 m long (permanently attached to microphone), 4 mm diameter, 6 conductor, shielded cable; output end stripped and tinned for connection to electronic device
• Accessories Furnished: Soft protective pouch

Designed to deliver easy, flexible control in conference and boardroom installations, the versatile U891Rx cardioid condenser boundary microphone features a touch-sensitive on-off switch that can be set to three modes: press-on/press-off, press to talk, and press to mute. The phantom-powered microphone is equipped with a unique PivotPoint® rotating output connector and an LED status indicator. UniGuard® innovations offer unsurpassed immunity from radio frequency interference; interchangeable elements are available in cardioid, hypercardioid and omnidirectional polar patterns; an 80 Hz low-cut UniSteep® filter reduces pickup of low-frequency ambient noise. The microphone's heavy die-cast case and silicon foam bottom pads minimize coupling of surface vibration to the microphone. The unit's self-contained electronics eliminate the need for an external power module.

• Element: Fixed-charge back plate, permanently polarized condenser
• Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
• Frequency Response: 30-20,000 Hz
• Low Frequency Roll Off: 80 Hz, 18 dB/octave
• Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
• Impedance: 200 ohms
• Maximum Input Sound Level: 130 dB SPL, 1 kHz at 1% T.H.D.
• Dynamic Range: 104 dB, 1 kHz at Max SPL
• Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
• Phantom Power Requirements: 11-52V DC, 4 mA typical
• Weight: 264 g
• Dimensions: 108.0 mm long, 84.0 mm maximum width, 23.0 mm height
• Output Connector: TB3M-type
• Cable: 7.6 m long, 3.2 mm diameter, 2-conductor, shielded cable with TA3F and XLRM-type connectors

• Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
• Ultra-quiet electronic switch can be set to any of three operating modes: "touch-on/ touch-off," "touch-to-talk" and "touch-to-mute“
• PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
• Superior off-axis rejection for maximum gain before feedback
• UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
• Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
• Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
• Low-profile design with low-reflectance finish for minimum visibility
• Available in two colors: black (U891Rx) and white (U891RWx)

C 547 BL 

"Non-crush" case
Inconspicuous
Hypercardioid polar pattern
Easy to repaint
 
Hypercardioid, studio-quality boundary microphone with rugged, "non-crush" case and
switchable bass-cut filter for reducing footfall noise, ideal for tough on-stage assignments.
Other benefits include optimum acoustic properties, high directivity, and neutral sound.
Having the same frequency response, the C 547 BL can be combined with the CK 47 with
excellent results.
Primarily designed for use in places of worship, theaters, and conferencing, the C 547 BL
is also a good choice for miking kick drums and other instruments.

SPECIFICATIONS:
Polar pattern hypercardioid
Frequency range 30 to 18,000 Hz
Sensitivity 8.5 mV/Pa (-42 dBV)
Max. SPL 133 dB (for 1% THD)
Equivalent noise level 22 dB-A
Signal/noise ratio (A-weighted) 72 dB
Bass filter 12 dB/octave at 150 Hz
Impedance 400 ohms
Recommended load impedance >1000 ohms
Supply voltage 9 to 52 V phantom power to DIN 45596
Current consumption