Content |
Offering outstanding Audio-Technica sound for surface-mount applications, the U851A features a PivotPoint® rotating output connector, UniSteep® filter and UniGuard® RFI-shielding technology. This battery- or phantom-powered condenser microphone accepts interchangeable condenser elements - available for boundary microphones in cardioid, hypercardioid and omnidirectional polar patterns. Its heavy die-cast case and silicon foam bottom pads minimize coupling of surface vibration to the microphone. With superior off-axis rejection and maximum gain-before-feedback, this professional microphone sets audio-quality standards in challenging acoustic environments.
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Superior off-axis rejection for maximum gain before feedback
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- UniSteep® filter provides a steep low-frequency attenuation to improve sound pickup without affecting voice quality
- Small-diameter UniPoint capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance black finish for minimum visibility
- Operates on battery or phantom power
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: Phantom: -40 dB (10.0 mV) re 1V at 1 Pa Battery: -41 dB (8.9 mV) re 1V at 1 Pa
- Impedance: Phantom: 200 ohms Battery: 270 ohms
- Maximum Input Sound Level: Phantom: 133 dB SPL, 1 kHz at 1% T.H.D. Battery: 123 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: Phantom: 111 dB,1 kHz at Max SPL Battery: 101 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 72 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 2 mA typical
- Battery Type: 1.5V AA/UM3
- Battery Current Life: 0.4 mA / 1200 hours typical (alkaline)
- Switch: Off, on-flat, on-roll-off
- Cable: 25.0' (7.6 m) long (permanently attached to microphone), 0.13" (3.2 mm) diameter, 2-conductor, shielded cable with TA3F-type connector
- Accessories: AT8531 power module; battery; soft protective pouch
|
C 562 CM
Small, low-profile boundary layer microphone Wide frequency range High sensitivity Ideal for inconspicuous installation in a room Suited for surveillance or recording The C 562 CM flush-mount boundary microphone uses the same transducer as the C 562 BL. The C 562 CM has been designed specifically for permanent, "invisible" mounting in ceilings, walls, tables, stage props, etc. Owing to its high sensitivity, the C 562 CM is a perfect tool for surveillance or live recording since a single microphone can cover an entire room. The supplied XLR phantom power adapter connects to the microphone cable through a miniature connector so installation holes can be smaller than the diameter of the phantom power adapter. SPECIFICATIONS: Polar pattern omnidirectional (hemispherical) Frequency range 20 to 20,000 Hz Sensitivity 25 mV/Pa (-32 dBV) Max. SPL 130 dB (k=1 %) Equivalent noise level 16 dB-A Signal/noise ratio (A-weighted) 78 dB Impedance 600 ohms Recommended load impedance >2000 ohms Supply voltage 9 to 52 V phantom power to DIN/IEC Current consumption Connector 3-pin XLR Cable 0.5 m (20 in.) Finish matte nickel plated Dimensions 20 dia. x 28 mm (0.8 dia. x 1.1 in.) Net weight 30 g (1.1 oz.) Shipping weight 195 g (76.9 oz.) |
Type of Transmitter UHF Frequency Agile
Input Connector Internal fitting for interchangeable capsules
Type of Microphone Electret Condenser Boundary Microphone
Polar Pattern Cardioid (Supplied)
Interchangeable Mic Heads Yes - R183B Omnidirectional, R184B Supercardioid and R185B Cardioid cartridges available
Frequency Response 50Hz to 17kHz
Battery Type/Approx. Life 9 Volt Alkaline - 7 hours based on alkaline battery
# Of Channels Over 100 channels between 692-862MHz, depending on locale
Mute Switch Programmable Touch-Sensitive Switch
Level Control Gain Adjustment Range: -6 to 34dBs
Antenna Type Internal
Display Microphone Status & Battery Life LEDs
Dimensions 3.625 x 1.8 x 5.17 (92 x 46 x 131mm) (WxHxD)
|
C 547 BL
"Non-crush" case
Inconspicuous
Hypercardioid polar pattern
Easy to repaint
Hypercardioid, studio-quality boundary microphone with rugged, "non-crush" case and
switchable bass-cut filter for reducing footfall noise, ideal for tough on-stage assignments.
Other benefits include optimum acoustic properties, high directivity, and neutral sound.
Having the same frequency response, the C 547 BL can be combined with the CK 47 with
excellent results.
Primarily designed for use in places of worship, theaters, and conferencing, the C 547 BL
is also a good choice for miking kick drums and other instruments.
SPECIFICATIONS:
Polar pattern hypercardioid
Frequency range 30 to 18,000 Hz
Sensitivity 8.5 mV/Pa (-42 dBV)
Max. SPL 133 dB (for 1% THD)
Equivalent noise level 22 dB-A
Signal/noise ratio (A-weighted) 72 dB
Bass filter 12 dB/octave at 150 Hz
Impedance 400 ohms
Recommended load impedance >1000 ohms
Supply voltage 9 to 52 V phantom power to DIN 45596
Current consumption |
A wide range condenser microphone with a cardioid polar pattern, the ultra-smart U891RCx is equipped with local or remote switching options. For flexible control in conference and boardroom installations, the unit's external contact closure ability allows a user to trigger an external device - a camera, for instance - from a switch on the microphone. Another ease-of-use feature: the microphone's electronic on-off switch can be set to three operating modes: touch-on/touch-off, press to talk, and press to mute. The mic is also equipped an 80 Hz low-cut UniSteep® filter to reduce pickup of low-frequency ambient noise. Its red LED status indicator can be controlled remotely. UniGuard® innovations offer unsurpassed immunity from radio frequency interference; interchangeable elements are available in cardioid, hypercardioid and omnidirectional polar patterns; a unique rotating PivotPoint® connector changes the cable exit point - no tools required. It requires 11 to 52V DC phantom power, which operates the microphone and switch circuitry.
- Designed for surface-mount applications such as high-quality sound reinforcement, conferencing, distance learning and other demanding sound pickup situations
- Ultra-quiet electronic switch can be set to any of three operating modes: "touch-on/touch-off," "touch-to-talk" and "touch-to-mute“
- External contact closure capability permits control of remote devices from microphone switch
- External LED control allows for accurate depiction of the live status of the microphone
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance black finish for minimum visibility
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 130 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 104 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
- Phantom Power Requirements: 11-52V DC, 4 mA typical
- Weight: 266g
- Dimensions: 108.0mm long, 84.0mm maximum width, 23.0mm height
- Output Connector: TB5M-type
- Cable: 7.6m long, 3.2mm diameter, 5-conductor shielded cable (2 conductors under shield; 3 control wires outside shield); TA5F-type connector at microphone end, output end stripped and tinned for connection to electronic device
| About the AKG Acoustics CBL 410 PCC
The AKG CBL 410 PCC Conference Microphone Set (Black) is a simple to use, plug and play desktop microphone for use with any PC or laptop. It improves audio quality incredibly when making a conference via VOIP. The microphone reproduces the voice with a clear and natural sound.
With its 3.5 mm stereo jack, it is a 100% plug and play device. No drivers are needed. Its ability to be cascaded makes the CBL 410 PCC the perfect tool for modern communication for both single person use in the office and/or multi-person use in a modern meeting room.
This microphone provides optimum intelligibility and audio quality for your meetings. The CBL 410 PCC is also an excellent choice for recording applications.
AKG Acoustics CBL 410 PCC Includes
- AKG 3x CBL 410 PCC PC Boundary Layer Microphones
- GHAP1 USB Adapter
- AKG Warranty
AKG Acoustics CBL 410 PCC Features
- Small and inconspicuous
- Exceptionally rugged
- Excellent sound quality
- High sensitivity
- Low self-noise
AKG Acoustics CBL 410 PCC Specifications
Polar pattern |
Omnidirectional |
Microphone Type |
Back electret condenser microphone |
Frequency response |
50 Hz to 20 kHz |
Impedance |
2000 ohms ±30% at 1000 Hz |
Sensitivity |
-42 dB ±3 dB (7.9 mV/Pa)Sensitivity: |
Maximum current consumption |
0.5 mA |
Supply voltage |
1.5 to 5 V DC |
Cable length |
100cm (40“) |
Connector |
TRS mini jack |
|
Reviews
There are no reviews yet.