Content |
The white-finished version of the U851R, the phantom-powered U851RW features a PivotPoint® rotating output connector, UniSteep® filter and UniGuard® RFI-shielding technology. Offering outstanding speech intelligibility and transparent sound quality for surface-mount applications, the U851RW accepts interchangeable condenser elements - available for boundary microphones in cardioid, hypercardioid and omnidirectional polar patterns. With a heavy die-cast case and silicon foam bottom pads to minimize coupling of surface vibration to the microphone, the U851RW is equipped with self-contained electronics, eliminating the need for an external power module.
- Designed for surface-mount applications such as high-quality sound reinforcement, professional recording, television, conferencing and other demanding sound pickup situations
- PivotPoint® rotating output connector allows cable to exit from either the rear or the bottom of the microphone
- Superior off-axis rejection for maximum gain before feedback
- UniGuard® RFI-shielding technology offers outstanding rejection of radio frequency interference (RFI)
- Self-contained electronics eliminate need for external power module
- Small-diameter UniPoint® capsule near boundary eliminates phase distortion and delivers clear, high-output performance
- Heavy die-cast case and non-slip silicon foam bottom pads minimize coupling of surface vibration to the microphone
- Low-profile design with low-reflectance finish for minimum visibility
- Available in two colors: black (U851R) and white (U851RW)
- Element: Fixed-charge back plate, permanently polarized condenser
- Polar Pattern: Half-cardioid (cardioid in hemisphere above mounting surface)
- Frequency Response: 30-20,000 Hz
- Low Frequency Roll Off: 80 Hz, 18 dB/octave
- Open Circuit Sensitivity: 34 dB (19.9 mV) re 1V at 1 Pa
- Impedance: 200 ohms
- Maximum Input Sound Level: 134 dB SPL, 1 kHz at 1% T.H.D.
- Dynamic Range: 108 dB, 1 kHz at Max SPL
- Signal to Noise Ratio: 68 dB, 1 kHz at 1 Pa
- Phantom Power Requiremens: 11-52V DC, 4 mA typical
- Switch: Flat, roll-off
- Weight: 9.2 oz (262 g)
- Dimensions: 4.25" (108.0 mm) long, 3.31" (84.0 mm) maximum width, 0.91" (23.0 mm) height
- Output Connector: TB3M-type
- Cable: 25.0' (7.6 m) long, 0.13" (3.2 mm) diameter, 2-conductor, shielded cable with TA3F and XLRM-type connectors
|
Boundary-layer Microphone
The LD Systems BM1 is an electret condenser microphone with a hemispherical directional characteristic.
For micing upright and grand pianos on stage or in the studio. Additional applications in the area of conference technology, transmission of roundtable discussions and theatrical performances.
Product type
Microphones
Type
Installations
Frequency response
50 - 20000 Hz
Directivity
half ball
Nominal impedance
250 Ohm(s)
Max. SPL (1% THD @ 1kHz)
135 dB
Phantom power requierements
48 V
Microphone input
XLR (3-pin)
Width
27 mm
Height
74.5 mm
Diameter
93.5 mm
Accessories (included)
cables (Mini-XLR / XLR, 6 m)
Weight
0,345 kg
|
C 562 CM
Small, low-profile boundary layer microphone Wide frequency range High sensitivity Ideal for inconspicuous installation in a room Suited for surveillance or recording The C 562 CM flush-mount boundary microphone uses the same transducer as the C 562 BL. The C 562 CM has been designed specifically for permanent, "invisible" mounting in ceilings, walls, tables, stage props, etc. Owing to its high sensitivity, the C 562 CM is a perfect tool for surveillance or live recording since a single microphone can cover an entire room. The supplied XLR phantom power adapter connects to the microphone cable through a miniature connector so installation holes can be smaller than the diameter of the phantom power adapter. SPECIFICATIONS: Polar pattern omnidirectional (hemispherical) Frequency range 20 to 20,000 Hz Sensitivity 25 mV/Pa (-32 dBV) Max. SPL 130 dB (k=1 %) Equivalent noise level 16 dB-A Signal/noise ratio (A-weighted) 78 dB Impedance 600 ohms Recommended load impedance >2000 ohms Supply voltage 9 to 52 V phantom power to DIN/IEC Current consumption Connector 3-pin XLR Cable 0.5 m (20 in.) Finish matte nickel plated Dimensions 20 dia. x 28 mm (0.8 dia. x 1.1 in.) Net weight 30 g (1.1 oz.) Shipping weight 195 g (76.9 oz.) | Electro-Voice PolarChoice Boundary Satellite Microphone Specifications:
Generation Element: Dual condenser,back electret
Frequency Response: 50 Hz to 20,000 Hz
Polar Patterns: Omnidirectional,Cardioid,Supercardioid,Hypercardioid
Sensitivity: Open Circuit Voltage,1 kHz:5.6mV/Pascal
Clipping Level (1% THD): >135 dB SPL
Equivalent Noise: Dynamic Range: >109 dB
Output Impedance,1 kHz: 200 ohms
Power Requirements: Phantom,12 - 52 VDC
Current Consumption: < 8 mA with P12 supp
Polarity: Pin 2 positive,referenced to pin 3,with positive
pressure on the diaphragm
Accessories Furnished: All versions of PolarChoice ship with the Shock Mount Kits and EV\'s Multiport™ windscreen. |
MX393C - Condenser Boundary Microphone, Built-in Preamp, 12-ft Tini "QG" ? to XLR Cable, Programmable Switch and LED Indicator
|
Type of Transmitter UHF Frequency Agile
Input Connector Internal fitting for interchangeable capsules
Type of Microphone Electret Condenser Boundary Microphone
Polar Pattern Cardioid (Supplied)
Interchangeable Mic Heads Yes - R183B Omnidirectional, R184B Supercardioid and R185B Cardioid cartridges available
Frequency Response 50Hz to 17kHz
Battery Type/Approx. Life 9 Volt Alkaline - 7 hours based on alkaline battery
# Of Channels Over 100 channels between 692-862MHz, depending on locale
Mute Switch Programmable Touch-Sensitive Switch
Level Control Gain Adjustment Range: -6 to 34dBs
Antenna Type Internal
Display Microphone Status & Battery Life LEDs
Dimensions 3.625 x 1.8 x 5.17 (92 x 46 x 131mm) (WxHxD)
|
Reviews
There are no reviews yet.