| Content | Audioengine D2 Premium 24-bit Wireless DAC
Audioengine D2 Premium 24-bit Wireless DAC allows you to stream wireless HD audio from your computer to any music system, independent of your Wi-Fi network. D2 includes USB and optical inputs, a high-performance DAC, plus the isolation benefits of wireless. Setup is fast and simple, with no software to install and without the frustration of trying to connect to your network.
D2 Technical Specifications
DAC typeDual Mode USB and Optical (SPDIF) wireless DAC
InputsUSB/Optical (SPDIF)
OutputsRCA Stereo/Optical (SPDIF)
D/A converterPCM1792A
Optical receiverAK4117
USB controllerTI1020B
Full-scale output2.0V RMS (RCA)
Output impedance100 ohms
Power source
Sender: USB 5V or included external supply
Receiver: Included external supply
Power requirements
Sender: 270mA
Receiver: 300mA
USB power filtering3-stage redundant regulation
SNR>115db
THD+N |
Streaming high quality music from your favourite mobile device is now easy with the rBlink Bluetooth** audio converter. Engineered by Arcam, and using the aptX®* transmission system, the rBlink allows any Bluetooth equipped music device to quickly and easily send music straight to a HiFi system with stunning quality.
- Audiophile Bluetooth Music Converter
- High quality music replay from mobile devices
- Burr Brown PCM5102 24bit DAC
- Uses aptX™ streaming technology
- High-end audio circuitry and components
- High quality cast aluminium casework
The rBlink uses a high-end PCM 5102 DAC to convert music to a line level output ready for connection to a whole host of audio systems. Installation is easy with a simple pairing system for new devices. Music is delivered by Arcam electronics so you can be sure of world-class sound quality too!
The rBlink comes housed in a stylish yet rugged cast aluminium case and is small and discreet enough to sit proudly next to your HiFi system just getting on with the job of delivering great music.
Technical Specifications
- DAC: TI PCM5102
- Frequency response: 10Hz — 20kHz, ±0.1dB
- Total Harmonic Distortion: + Noise 0.002%
- Signal-to-noise ratio (A –Weighted): 106dB (24-bit)
- Line output level: 2.15Vrms
- Supported CODECs: SBC, AAC, aptX®
- Power requirements: 0.7W max
- Dimensions (wxdxh, mm): 75 x 100 x 26
- Weight: 350g
| Denon Professional's Solution Series is designed to be the best friend of audio contractors. Its specialty is solving audio challenges easily and inexpensively by getting signal to someplace that would be otherwise difficult or inconvenient. Simple to install, configure and operate, the Solution Series products belong in the toolbox of every audio installer.
For applications where unsightly cable runs or drilling of holes is not permissible, the DN-202 WT and WR combination is ideal for getting stereo audio from point A to B. The DN-202WT is a wireless audio transmitter with balanced XLR and ¼-inch inputs, enabling users to send audio from a professional audio mixer or source through walls and ceilings up to 100 feet (30m) away. The DN-202WR is the companion receiver, featuring balanced XLR and ¼-inch outputs for connection to loudspeakers or amplification systems. Multiple DN-202WRʼs may be used with a single DN-202WT to optimize sound coverage at an event or split indoor/outdoor/multi-level venues.
Features
- For use with DN-202WR
- Sends audio up to 30m (100 ft) without wires
- XLR and 1/4” audio inputs
- Able to broadcast to multiple receivers (sold seperately)
- External, articulating antennas ensure optimum transmission and reception
- Perfect for event spaces, houses of worship, entertainment venues, education, retail, and more
Package Contents
- DN-202WT
- Power adapter (5VDC, 3A, center-positive)
- User Guide
- Safety and warranty manual
| Driver Complement: One front-firing x 4.0” midwoofer, Four
x 1.0” aluminum dome tweeters, Two x 4.0” bass radiators
Amplification: 1 x 30W Woofer, 4 x 15W tweeters
Wireless Connectivity: 2.4GHz & 5.8GHz
Inputs: Optical, Analog, Ethernet, USB-A for firmware
updates and phone charging |
| Construction |
Mono speaker |
| Built-in Class-D Power Amplifiers |
2 |
| Drivers |
2 |
| Tweeter |
1 x 25 mm |
| Mid-Range |
No |
| Woofer |
1 x 89 mm |
| High Resolution Audio support |
Yes |
| USB input (mass storage) |
Yes |
| Analog input (3.5mm mini jack) |
Yes |
| Stereo Pairing |
Yes |
| Usage as Surround SPK for Soundbar DHT-S716H |
Yes |
| Supports Subwoofer with HEOS built-in |
Yes |
| Bass and Treble Control |
Yes |
| Proximity Sensor |
Yes |
| Quick Select Buttons |
3 |
| Volume +/- |
Yes |
| Play/Pause |
Yes |
| HEOS built-in |
Yes |
| WiFi 2.4 GHz |
IEEE 802.11b/g/n |
| WiFi 5 GHz |
IEEE 802.11a/n/ac |
| Airplay 2 |
Yes |
| Bluetooth |
Yes |
| USB port for direct connection of stored music |
Yes |
| Wired Network (RJ-45) |
Yes |
| 3.5mm AUX Input |
Yes |
| Available colors: White / Black |
Yes / Yes |
| Power Supply (built-in) |
AC 100 – 240 V, 50/60 Hz |
| Dimensions (W x H x D) |
120 x 187 x 120 mm |
| Weight in kg |
1.7 |
| The best of all worlds - amazing sound, effortless wireless streaming with AirPlay®, a LightningTM connector for docking the latest generation of iPhones® and iPods® and a design that fits almost anywhere. Versatility, convenience and stunning performance; Z2 is the dock that has it all.
| Model |
Z2 |
| Description |
Wireless Music System |
| Technical features |
Apple® AirPlay® technology
Lightning connector
Digital Signal Processing (DSP)
High Quality Class-D amplifier
Switch mode power supply
FlowportTM
Remote control |
| Drive units |
2x 87.5mm (3.5in) full range |
| Frequency response |
50Hz - 20kHz ±3dB on reference axis |
| Frequency range |
-6dB at 42Hz and 22kHz |
| Amplifier power output |
2x 20W |
| Input voltage |
100V - 240V ~ 50/60Hz |
| Rated power consumption |
36W |
| Standby power consumption |
|
|
Reviews
There are no reviews yet.