| Content |
Avantone Active MixCubes Powered Full-Range Mini Reference Monitors
The Avantone MixCubes are shielded, full-range mini reference monitors. Their design is inspired by the legacy of the 5C Sound Cubes used in virtually all-major studios for the last 25 years.
Application
Active Recording / Mixdown Monitors
Engineering Objective
The Avantone Active Mixcubes are designed to be high-resolution, full-range powered mini-reference monitors for fixed or remote locations.
The secondary engineering facet was to create a timeless design that compliments a single full-range transducer.
Performance Objective
Studios primarily use 2-way & 3-way larger monitors designed to represent a wide range reference viewpoint at higher listening levels. However, in this newly developing age of High Definition Audio, there is still a need to also hear what your mix will sound like when played back over small "bass-challenged" systems such as televisions, clock radios, computers, car stereos, iPod docking stations, etc. It is important to make mixing judgments based partially on listening to reference monitors that will not impart tonal anomalies caused by crossovers or inferior full range drivers. Particular attention is always paid to the critical mid-range vocal/guitar/keyboard areas. This is where having a full-range monitor without a crossover is truly revealing. Ten months of R&D comparative listening & tweaking went into the voicing of the AVANTONE MixCubes. The result is a very smooth sounding, full range upgrade from the original 5C Sound Cubes. Listening tests reveal that the MixCubes have a smooth, more open, transparent top end response with extended bass while maintaining their basic original character.
Cabinet Design
The original 5C Sound CubesTM were made of ½" particleboard covered with a glue-on wood grain contact paper. We chose to use thicker, denser MDF board because of its high rigidity and inherent low-resonance characteristics. We started with a 165mm (6 1/2“) sealed cube design with radiused edges. We then chose an elegant Polyurethane high gloss "RETRO-CREAM" finish. The originals had either screws or on later models plastic binding posts mounted on a recessed plastic cup. We upgraded to high-end nickel plated, machined solid metal binding posts (Dual banana spacing) mounted on a black anodized ,milled and silk-screened aluminum terminal plate. Next we added a 7mm thick neoprene pad embedded into the base of the cabinet to serve as a skid-resistant acoustic isolator. Additionally, for creative mounting situations, we recessed an industry standard 5/8“-27 mic stand mount into the base.
Driver Design
The originals were a basic 5" stamped frame design. We designed a proprietary 5.25" die cast aluminum frame driver/cone assembly to exceed the performance of the originals. The mounting bezel is then polished for an elegant appearance. The paper cone, chosen for its musical character, is custom designed & crafted using the finest New Zealand pulp with mica fibers added for lighter weight & rigidity. The cloth surround is made in Japan to exacting uniform thickness tolerances. The Top Plate and T-Yoke of driver are made of Sumitomo 1008 low carbon steel enabling the highest modeled flux density in the gap. The magnets are Y- 40 GRADE (MIL-SPEC) yielding a 43oz. High Power-low distortion motor structure.
Amplifier Design
We designed the amp module from the ground up to be a true professional-grade amplifier. It incorporates "overkill" concepts in component selection as well as safety. The result is a "no-compromise" amp with robust headroom characteristics that will rival the performance of much higher priced studio rack mount amps.
Specifications
System Type
Active (Self-powered) shielded full-range stereo pair
Frequency Response
90Hz - 17,000Hz (useful musical range)
>Driver Impedance
Nominal 8 ohms
Max SPL
104db @ 1 meter = 1%THD (PINK NOISE)
Amplifier Type
Class A/B
Amplifier Power
60 watts RMS@ .005% THD (1KHz)
Amp Frequency Response
22Hz-50KHz +0dB/- 3dB (90Hz-50KHz +/-0dB)
Noise
S/N -113 dB
Sensitivity
0dBu (.775VRMS) input at maximum volume (+6dB) = 104dB SPL
Driver
Proprietary design 5.25" cast aluminum frame / paper cone / shielded
Cabinet
sealed / 18mm MDF / Dacron acoustical stuffing
Inputs
XLR & TRS (COMBO JACK) +4/Balanced and -10 unbalanced
Weight
7 lb 5 oz (per speaker)
Dimensions
165mm x 165mm x 165mm (6 1/2" x 6 1/2" x 6 1/2" in)
|
* Active studio monitors with USB audio interface
* 4.25-inch magnetically shielded, inverted cone, copolymer woofer
* 1-inch silk dome high frequency driver
* 2 x 20 watts of internal stereo power
* Two combination mic and instrument/line inputs
* Two 1/8-inch stereo headphone outputs with level controls
* Includes Cakewalk® Sonar LE music production software
* Mic and instrument/line gain control with clip LED
* 16-bit 44.1kHz/48kHz
* Stereo RCA and 1/8-inch aux inputs
* 2-position switch for no-latency direct stereo and mono monitoring
* Mix control to balance computer and audio sources
* USB and speaker cable included
|
MYTHO 8 is a two-way reference studio monitor equipped with two separate AB amplifiers - 200 W for the low frequencies and 100 W for the high - unparalleled for low distortion and natural sound. It features a high quality large metal dome tweeter for the best vocal reproduction and a 8” neodymium vented woofer with a large sized 51 mm voice coil that guarantees very high energy for tight and controlled bass reproduction and perfect thermal stability with minimum power compression.
The magnetic circuit features a special air ventilation to reduce air compression, air noises and minimize distortion in large excursion situations. Thanks to the deeper low frequencies reproduced by its 8” woofer, the MYTHO 8 is perfect for medium to large control rooms.
A dedicated high quality DSP is provided on board. The cabinet is made in aluminium, internally braced and reinforced to improve low frequencies behaviour and reduce resonances.
| Acoustical Specifications |
|---|
| Frequency Response -3 dB: | 35 Hz | ÷ 20 kHz | | Max SPL: | 116 dB | | | Horizontal coverage angle: | 110° | | | Vertical coverage angle: | 70° | | | Compression Driver: | 1" neo, metal dome | | | Woofer: | 8" neo, ICC technology | |
| INPUT/OUTPUT SECTION |
|---|
| Input connectors: | combo XLR/Jack | | | Input sensitivity: | -6/+6 dBu | |
| PROCESSOR SECTION |
|---|
| Crossover frequencies: | 1800 Hz | | | Protections: | thermal, excurs., rms | | | Limiter: | soft limiter | | | Controls: | bass tilt, roll-off, treeble tilt, desktop, DSP controlled | |
| AMPLIFIER SPECIFICATIONS |
|---|
| High frequencies: | 100 Watts | | | Low frequencies: | 200 Watts | | | Cooling: | convection | | | Connections: | vde | |
| CABINET |
|---|
| Cabinet Material: | die cast aluminum | | | Hardware: | orientation adjustable stand | |
| PHYSICAL SPECIFICATIONS |
|---|
| Height: | 430/17 mm/inch | | | Width: | 310/12.2 mm/inch | | | Depth: | 300/11.8 mm/inch | | | Net Weight: | 16.150/35.60 Kg/Lbs |
|
DM-2100: 2.1-ch Speaker System
Features The DM-2100 2.1-ch Speaker System is an affordable way to add accurate reference monitoring with a subwoofer for enhanced bass response. The left and right speakers each offer 15 watts of power, while the 50-watt subwoofer provides a powerful low-end boost. And with 24-bit/96kHz digital inputs, the DM-2100 is perfect for use with Roland/BOSS digital studios and instruments, or with computer systems and more.
- Affordable 2.1-channel monitoring system with 24-bit/96kHz digital inputs
- Powered bass reflex speakers with 15 watts per side and flat frequency response
- Active subwoofer with 50-watt amplifier for increased low end
- Front-mounted controls convenient located on right speaker
- Coaxial and optical digital inputs, plus analog inputs (RCA and 1/4-inch type)
- Sleek black wooden cabinets with magnetic shielding
Rated Output Power50W + 15W + 15WSpeakerSubwoofer: 16cm, Satellite Units: 9.2cmNominal Input LevelLine 1: -10dBu, Line 2: -10dBuInput Impedance18k ohmControlsR Channel: Bass Control Knob, Treble Control Knob, Volume 1 (Digital In/ RCA pin), Volume 2 (1/4” phone), Power Switch, Digital Input Select Switch, Phase SwitchConnectorsR Channel: Line 1 Jack (L, R; RCA pin), Line 2 Jack (L (MONO), R; 1/4” phone), Optical Input Connector, Coaxial Input Connector, Dedicated connector for power control and audio signal, Channel Input Jack (R; RCA pin),
L Channel: Channel Input Jack (L; RCA pin),
Sub Woofer: Dedicated connector for power control and audio signal, Channel Output Jacks (L, R; RCA pin), AC In JackDigital InputSampling Rate 32/44.1/48/96 kHz, D/A Convertor 24 bitsPower SupplyAC117, 230 or 240VAccessoriesSpeaker Cables (RCA pin type), Dedicated Cable for power control and audio signal, Power CableSize and Weight ( Satellite Units )Width130 mm5-1/8 inchesDepth160 mm6-5/16 inchesHeight200 mm7-7/8 inchesWeight
Size and Weight ( SubWoofer )Width240 mm9-1/2 inchesDepth300 mm11-13/16 inchesHeight330 mm13 inches
|
PRICE PER UNIT
S2X
The S2X brings together the virtues of the ʽclassicalʼ 7” woofer and tweeter combination by using ADAM innovative technologies and top-class materials.
The HexaCone 7” woofer is driven by a sophisticated magnet system with a 2” voice coil creating a greater linear excursion. This produces more dynamics than one would assume in a monitor of such small proportions. As a result, in addition to the unsurpassed audio quality of the X-ART and A/B amplifier combination, this monitor surprises the listener with a very powerful, deep, but always tight and precise low end.
Review at a glance: "Sonic sensation“
“The ADAM Audio S2X can convince in all areas, concerning the sound as well as the workmanship, and are worth every Euro. […] a no-compromise tool for all who mean serious business, whether in music or postproductions.” (www.96kHz.de, 03/2010)
“We started off with a classical string quartet recording and let´s just say right away that the S2Xs floored us. Several adjectives spring to mind [...] - wide open, transparent, effortless, breathtaking realistic, loud, dynamic, involving... [...] If you close your eyes and continue listening, the S2Xs seem to ‚disappearʽ almost entirely. [...] you gradually become less aware that you´re listening to speakers because they´re like an open window on the music itself. [...] Result: These monitors are up there with the best we´ve tried so far.” (MusicTech, 01/2010)
| Woofer |
| | Number | 1 | | Basket Ø | 7.5" (186 mm) | | Voice coil Ø | 2" (50 mm) | | Cone material | HexaCone | | Tweeter |
| | Number | 1 | | Type | X-ART | | Diaphragm area | 4 inch² (2420 mm²) | | Equiv. Diaphragm Ø | 2" (56 mm) | | Velocity transform ratio | 4:1 | | Diaphragm weight | 0.17 g | | Built-in Amplifiers |
| | Woofer | 1 | | Type | PWM | | Amp. power RMS / music | 250 W / 350 W | | Tweeter | 1 | | Type | A/B | | Amp. power RMS / music | 50 W / 100 W | | Control panel |
| | Input Sensitivity (coarse) | -20 to +8 dB (4 dB steps) | | Input Sensitivity (fine) | -1.5 to +2 dB (0.5 dB steps) | | EQ 80 Hz | 0 to +6 dB (1 dB steps) | | High Shelf EQ > 6 kHz | ±4 dB (1 dB steps) | | Low Shelf EQ | ±4 dB (1 dB steps) | | Tweeter gain | ±2 dB (0.5 dB steps) | | Input connectors |
| | Analog | XLR | | Digital (optional) | AES/EBU / SPDIF / word clock | | General data |
| | Panel | Front | | Frequency response | 35 Hz - 50 kHz | | THD > 80 Hz | ≤0.8 % | | Long term output | ≥110 dB | | Max. peak | ≥120 dB | | Crossover frequencies | 2200 Hz | | Input impedance | 10 KOhm | | Weight | 23.8 lb (10,8 kg) | | Magnetically shielded | Optional | | Height x Width x Depth | 14.5" (370 mm) x 8.5" (220 mm) x 12.5" (320 mm) | | Warranty | 5 Years |
| Delivery contents | |
Power cord, Manual
|
| Behringer MS-16 2x8W 2-Way Active Personal Monitor System
The Behringer MS16 Studio Monitors feature an active 2-way design with powerful 4'' woofers and 1.5'' tweeters, powered by two 8 watt amplifiers. Offering two line inputs and a microphone input, the Behringer MS16 monitors are perfect for both home studios and general multimedia applications.
Full Description
Compact and Ideal For Home Studio
The Behringer MS16 Studio Monitors, Pair are the ideal studio monitor for your home studio project. Whether that be mixing, producing, or even listening the MS16 Studio Monitors turn your computer into a personal home studio. Its powerful 4" woofers provide thumping bass, whilst the high resolution tweeters provide clean high frequencies. Also featured are dedicated volume, bass and treble controls for extra flexibility. They also make excellent add-on speakers for electronic keyboards and playing a live performance.
Input Connections
The MS16 Studio Monitors feature multiple input options featuring a 1/8" stereo input for connecting up CD, MD and MP3 players. The dual RCA jacks allow for stereo keyboard modules and tape decks. Furthermore there is a 1/4" inch to allow connections for a dynamic microphone or electric guitar enabling you to sign or play along with prerecorded tracks.
Features
- Compact stereo speaker system ideally suited for home studios, multimedia applications, keyboard and vocal monitoring, etc.
- Powerful 4'' woofers and high-resolution tweeters powered by two 8 watt amplifiers
- Dedicated Volume, Bass and Treble controls for more flexibility
- Stereo RCA inputs for sound cards, keyboards, etc. that can be used simultaneously with a second stereo source (e. g. CD/MD player) through 1/8'' TRS stereo input
- Separately adjustable 1/4'' TRS microphone input mixable with stereo inputs for playback and vocal monitoring applications
- 1/8'' TRS headphone connector with auto-mute loudspeaker function
- Magnetically shielded for placement near computer monitors
- Designed and engineered in Germany
Specifications
- Woofer: 4''
- Tweeter: 1.5''
- Output Power: 2 x 8 Watts
- Frequency Response: 80Hz - 20kHz
- Speaker Impedance: 4?
- Input 1:
- Connector: 1/8'' TRS Stereo
- Input Level: -10dBm, 10k?
- Input 2:
- Connector: RCA Stereo
- Input Level: -10dBm, 10k?
- Mic Input:
- Connector: 1/4'' TRS
- Input Level: -50dBm, 50?
- Dimensions: 9.5'' x 5.5'' x 6'' / 241mm x 140mm x 150mm (H x W x D)
- Weight: 4kg
|
Reviews
There are no reviews yet.