Axel Technology Boxtel MKII Basic Telephone Hybrid

• Compact telephone hybrid
• 1 POTS/PSTN or GSM DualBand telephone line
• Send/Receive audio levels control and visualization
• Backlit Hook/Ring button
• Software configuration
• Phone call auto-answer feature
• International selection of the line impedance
• Remote control
• Potentiometer levels and front panel control
• Analogue Send/Receive balanced over XLR
• 1 USB port
• GPIO to remotely control Telco N-1 modules

• Dimension LxHxD 22x5x13cm
• AC Rate 230Vac / 110Vac 50 Hz / 60 Hz 30VA
• Type of power supply Switching power supply, worldwide
• Weight ≈ 2500 gr
• Operating Temperature -5°C / +50°CANALOG INPUT MODULE (send)
• Connectors: XLR, female - Electronically balanced
• Operative Nominal Level: 0 dBu
• Line Impedance 10 kΩ (Electronically balanced selectable) EMIsuppressed
• Distortion: less than 0.01% TDH+NOISE (0.0dBu 1Khz)
• Input Modes: MonoANALOG OUTPUT MODULE (receive)
• Connectors XLR, male - Electronically balanced
• Output Level 0dBu +4dBu +6dBu Max +20dBu
• Load Impendance 600 Ω
• Distorsion Less than 0.01% TDH+NOISE (0.0dBu @ 1Khz)
• Output Modes: MonoTELEPHONE MODULE PSTN / POTS
• Connectors LINE RJ 11C 6/4 socket
• Connectors SET RJ 11C 6/4 socket
• Bandwidth telephone line 100Hz 5kHz, -3dB @ 1 kHz
• Telephone line compliance ETSI TBR21, FCC Part68
• Isolation 3 kVREMOTE INTERFACE
• Digital Inputs GP In 2x GP In opto coupled. Only 1 is used as Hook
• Digital Outputs GP Out 2x GP Out Open Collector opto isolated. Only GPOut 1 is used as RingTechnical Specification about BoxTel MKII GSM (Additional )
• TELEPHONE MODULE GSM Module
• Standard DualBand GSM 900/1800 Mhz Phase 2+
• Frequency GSM 900: (Tx) 890 915 Mhz / (Rx) 935 960 Mhz
• GSM 1800: (Tx) 1710 1785 Mhz / (Rx) 1805 1880 Mhz
• Sensitivity -104 dB
• Channel bandwidth 200 kHz
• Maximum consumption 0.25 W / 0.5W
• Stand-by consumption
• Sensitivity -104 dB
• Dial tone frequency 450 Mhz Standard
• Environment noise
• Transmitting Power
• External Antenna 2.5 dBi omnidirectional with 1mt standard cable
• External power supply unit Input: 100-240 Vac Output: 12 V 500 mA
• External Antenna connector SMA
• Total rechargeable battery time 6 h
• PSTN / POTS connector RJ 11C 6/4 socket
• Operating temperature 0°C ≈ +45°C
• EN COMPLIANCY for GSM Modul EN 60950-1
• EN 301 489-1/-7
• EN 301 511

Shure DP11EQE Dynamics Processor Specification:

    GENERAL:
        Frequency Response: 20 to 20k Hz +/- 1.0 dB re 1 kHz
        Dynamic Range: 104 dB minimum, A-weighted, 20 Hz to 20 kHz
        Sampling Rate: 48 kHz
        Digital-to-Analog, Analog-to-Digital Conversion: 20 bit resolution
    Voltage Gain:
        1 dB +/- 1dB (power off)
        12 dB +/- 2 dB (input 10 dBV, output +4 dBu)
        12 dB +/- 2 dB (input +4 dBu, output 10 dBv)
        0 dB +/- 2 dB (equal input and output sensitivities)
    Impedance:
        Input: 47 kilohms +/- 20% actual
        Output: 120 ohms +/- 20% actual
    Input Clipping Level
        +18 dBu minimum (at +4 dBu setting)
        +6 dBV minimum (at 10 dBV setting)
    Output Clipping Level
        +18 dBu minimum (at +4 dBu setting)
        +6 dBV minimum (at 10 dBV setting)
    Total Harmonic Distortion
            LED Signal Indicators
        Signal: 40 dB
        Clip: 6 dB down from input clipping
    Propagation Delay from Input to Ouput
        0.8 ms (all filters flat, no dynamics processing, 0 ms delay), up to 2.1 ms (all processing enabled)
    Polarity
        Input to output: inverting optional (default: non-inverting)
        XLR: pin 2 positive with respect to pin 3
        1/4-inch TRS: tip positive with respect to ring
    Operating Voltage
        DP11EQ: 120 Vac, 50/60 Hz, 50 mA max
        DP11EQE: 230 Vac, 50/60 Hz, 25 mA max
        DP11EQJ: 100 Vac, 50/60 Hz, 50 mA max
    Temperature Range
        Operating: 0 degrees to 60 degrees C (32 degrees to 140 degrees F)
    Fuse
        DP11EQ: 120 Vac. Fuse: 100 mA, 250V time delay
        DP11EQE: 230 Vac. Fuse: 50 mA, 250 V time delay
        DP11EQJ: 100 Vac. Fuse: 100 mA, 250 V time delay
    Dimensions
        219 mm x 137 mm x 44 mm (8-5/8 in x 5-3/8 in x 1-3/4 in)
        Weight: 930 g (2.05 lbs)
    DYNAMICS PROCESSOR
        Gate and Expander:
        Threshold: 72 to 1 dB, 0.5 dB resolution
        Attack: 1.0 to 200 ms
        Decay: 0.05 to 1 second
        Gate Hold Time: 0 to 0.5 seconds
    AGC Leveler
        Threshold: 72 to 1 dB, 0.5 dB resolution
        Attack: 0.2 to 3 seconds
        Decay: 0.5 to 5 seconds
        Hinge: Threshold to 1 dB, 0.5 dB resolution
    Compressor and Limiter
        Threshold: 72 to 1 dB, 0.5 dB resolution
        Attack: 1.0 to 200 ms
        Decay: 0.05 to 1 second
        Knee: Hard or Soft selectable
    No Overshoot Peak Limiter
        Propagation delay: 1 ms
        Threshold: 72 to 1 dB, 0.5 dB resolution
        Attack: 0 msDecay: 100 ms
    PARAMETRIC EQUALIZER
        Parametric Filter Frequency Bands
        Up to 9 bands, variable frequency, variable Q
    Boost/Cut Range
        +6 dB to 18 dB per band
        Q Range
        1/40-octave to 2 octave
    High and Low Shelf/Cut Filters
        Shelf, +6 to 18 dB per filter
        Cut, 12 dB per octave nominal
    DELAY
        Up to 1.3 seconds, 21 microsecond resolution

Description

The alphaton Feedback-Controller FC-100 is a revolutionary product for every microphone
application including wireless types. It can provide effective feedback control to any sound
reinforcement situation. It can also eliminated string feedback in guitars and bass instruments
which are equipped with piezo or condenser pickups.
The FC-100 provides 6 to 10 dB of feedback protection by analysing the incoming signal,
detecting the presence of feedback and then notching out the feedback frequency.
The FC-100 relieves the sound engineer automatically. It works dynamically and eliminates a
feedback signal before it can grow into a peak. Internally a discriminator circuit detects the
presence of regenerative feedback and triggers the automatic equaliser to insert a notch where
the feedback peak is coming up. This normally prevents other peaks from developing but if they
do, the process is repeated at high speed, thus keeping feedback under control.

Technical Data
In- and Outputs transformer balanced
max. Inputlevel + 3 dB
Gain (RS=200 Ohm, RL=2kOhm) 0 dB
Frequency Response 20 Hz ... 20 kHz, +/- 1,5 dB
Feeback Cancellation  6 ... 10 dB
Power Requirement  30 ... 48 V Phantom
Current drain ca. 8 mA
External Power Supply 9 ... 20 V DC, 3,5 mm jack, tip +
Housing Aluminium Diecast
Weight  285 grams
Dimensions  112 x 60 x 32 mm

The DPR-504 is a 4-channel noise gate.

Each channel features:
A parametric key filter with key filter listening.
Simultaneous key level and threshold metering with average and
peak metering.
A gate status LED.
A RELEASE/HOLD control (hold tracks proportionally with release
times).
Attack switchable auto/fast (auto tracks signal dynamics for optimum
setting).
Link (links two channels together).
Key source allows external triggers.

The Range switch selects between 7OdB and 2OdB gating depth to
provide alternative release profiles.
The unit features electronically balanced inputs and outputs. 

Psychoacoustic Bass Enhancement Unit with Renaissance Compressor, MaxxBass, and L2

Bass Boost for Live Sound, Broadcast, Mastering & Post Production
They say that in electronics there's no new technology - the only changes
will be in size and applications. Things will simply keep getting smaller
while doing more. This is certainly true in music (just think about what an
iPod can do), but as we design smaller playback systems with small speakers,
there are also some tradeoffs, particularly in music. Clever cabinet designs and
high-excursion drivers can get you only so far. Any audio engineer trying to extract
bass from real-world components must eventually face the laws of physics:
All things being equal, small boxes and speaker cones can't move enough air
to produce a room-shaking low end. When working with systems tiny enough to
toss in a shoulder bag, the challenge is even more formidable. Interestingly enough,
Waves MaxxBCL has a new solution to this problem using a very old concept.

Waves MaxxBCL at a Glance:
MaxxBass? Bass Enhancement adds deep bass sound without adding bass frequencies
Waves Renaissance Compressor
L2 Ultramaximizer Peak Limiter
24-bit/96kHz resolution with 48-bit, double-precision processing
Supports optical, coaxial S/PDIF, AES/EBU, balanced and unbalanced line-level analog signals

MaxxBass Bass Enhancement
Waves' patented algorithm adds stunning bass sound without adding bass frequencies,
delivering a bigger bottom end. MaxxBass? allows your audience to hear bass frequencies
lower than physically present by applying psychoacoustic principles: Even though we
can hear a bass guitar from a small speaker, we don't actually hear the fundamental
frequency because the speaker can't produce a pitch that low. Instead, we hear the
harmonics that the speaker can produce, and this causes the brain to create the "missing
fundamental." MaxxBass? takes this well-known psychoacoustic phenomenon to the
maximum, giving you the ability to extend the perceived frequency response of a system
about two octaves below its physical limitation.
To accomplish this, the signal is split: high frequencies are passed to the output (to be
added back to the bass). The bass signal is analyzed and a specific series of upper
harmonics are created. Because the dynamics of the original bass are duplicated in these
harmonics, the result is the most natural sounding bass enhancement available. The
MaxxBass? harmonics and the original bass can be mixed in any proportion at the output.
To provide more control, a high-pass filter can be switched in, allowing the harmonics only to
be passed along as an "image" of the original bass frequencies, which is useful when working
with a system with known low-frequency limitations to avoid over-excursion of the speaker drivers.

Renaissance Compressor
Designed to provide the classic warm sound of analog compressors, the legendary
Renaissance Compressor controls dynamics with studio-style warmth that flatters
full mixes, vocals, or instruments. Controls include selection of vintage-style Opto
or modern Electro compression, and threshold, ratio, and attack controls. Waves
ARC? (Automatic Release Control) algorithm dynamically optimizes the compressor's
release value for a wide-ranging input. ARC? reacts much the way a human ear
expects, and can produce increased RMS level with greater clarity.
In general, the release is faster for peak transients and slower for the overall RMS
level. The ARC? system varies the release time to fit the ear's expectations while
increasing RMS, and without creating distracting artifacts. In this way, the
Renaissance Compressor can serve as a leveler plus a fast compressor simultaneously.

L2 Ultramaximizer Peak Limiter
Heard on countless hit records and soundtracks, the L2 Ultramaximizer puts sound
up-front with breathtaking transparency. The L2 is capable of a very fast, overshoot-free
response. Once the limiter threshold has been set, you can define the actual peak level
that the processed signal will reach. Once set, limiting and level re-scaling becomes a
one-shot process. The L2 can significantly increase the average signal level without
introducing any audible side effects. Yet there is plenty of range to recreate "vintage"
effects such as level pumping or severely limited dynamic range if you like.

Pristine Sound Quality
The MaxxBCL offers 96kHz, 24-bit resolution with a 48-bit, double precision internal
processing path and a dynamic range of ~125dB. The totally passive analog input
path to the ADC uses Jensen transformers, while the output path also features Jensen
analog output transformers. The unit is galvanic-isolated, which prevents ground loops
and allows it to operate in electrically unstable environments. Waves MaxxBCL combines
the highest quality converters available with unequalled processing algorithms to offer you
astonishing new power in bass enhancement, dynamics processing, and format conversion
(analog-to-digital, digital-to-analog, and digital re-quantization).

Versatile Connections
The MaxxBCL supports optical, coaxial S/PDIF, AES/EBU, balanced and unbalanced
line-level analog signals. MaxxBCL features a unique set of input and output trim settings:
analog input headroom can be set from 9dB above 0dBu to 24dB in six precise steps
(using the rear-panel selectors). Analog output level is similarly set with a separate
rear-panel trim pot offering you the ability to connect between devices with a wide range
of input and output levels.

Waves MaxxBCL Features:
User Interface:
Clear backlit displays, meters, and buttons are visible in all lighting conditions
THD + Noise: ? 0.0006 % @ 1kHz @ -1dBFS
Precision metering with resettable peak hold options (2 sec, infinite)
Accurate, wide-range metering covering 90dB for input and output
and 12dB for compressor and limiter attenuation
Quick access independent bypass on each processing block
Tactile feedback knobs
Four easy store/recall user presets
Input / Output:
Analog, AES/EBU, S/PDIF
Independent rear-panel input and output headroom calibration in six steps
(+9, 12, 15, 18, 20, and 24 dBu)
Passive analog inputs to the A-to-D converters using Jensen analog input transformers
Jensen analog output transformers
High-performance IDR dithering to 16- or 24-bit output
Precise input level setting using 1% resistor networks
Processing:
48-bit end-to-end internal processing path
Switchable compressor/MaxxBass? order
MaxxBass:
Adjustable processor frequency from 25 to 120Hz
Adjustable harmonic mix percentage from 0 to 100%
High-pass Filter "harmonics only" option
Compressor:
Opto/Electro mode selection
Threshold (0-60dB), Ratio (1:1-12:1), and Attack (0.5, 1, 2, 5, 10, 20, and 50 ms) controls
Proprietary ARC? Automatic Release Control
Automatic gain makeup
Limiter:
Overshoot-free look-ahead processing
Adjustable Threshold (0-18dB)
Adjustable Output Ceiling (0-18dBFS)