Content | Behringer C-2 2 Matched Studio Condenser Microphones
2 Matched Studio Condenser Microphones
- 2 matched condenser microphones for stereo studio recording and live applications
- Ideal as main and support microphones for studio and live applications
- Cardioid pickup pattern for effective feedback elimination
- Low-mass diaphragm for ultra-wide frequency response and ultimate sound reproduction
- Switchable low-frequency roll-off and input attenuation
- Ultra low-noise transformerless FET input eliminates low-frequency distortion
Excellent Source Isolation
Our C-2 mics also feature a low-frequency rolloff switch to eliminate infrasonics (mic handling noise, sound created by creaky stages), as well as a switchable -10 dB input pad to accommodate hot signals, such as a really loud vocalist or overzealous cellist.
The cardioid pickup pattern provides unparalleled sound source separation and feedback rejection. C-2 mics contain ultra low-noise transformerless FET input circuitry that can handle extreme dynamics with a maximum sound pressure level of 136 dB. So even if the featured performer at your next recording session or live show happens to be a revved-up jet engine, this workhorse mic will not distort!
Sound That Astounds
Every stitch of these mics is designed to deliver beautiful sound. Beginning with the gold-plated 3-pin XLR connector, you get the highest signal integrity.
Once connected to your system, youʼll notice these twin pro-caliber microphones have a 4 dB boost in the 1 kHz - 8 kHz range. For those of you new to condenser mics, this basically means youʼll get a slightly brighter sound that will give the perfect shape to cymbals and overhead miking. Acoustic pianos and choirs also benefit greatly from this type of frequency response.
Excellent Source Isolation
The cardioid pickup pattern provides unparalleled sound source separation and feedback rejection. C-2 mics contain ultra low-noise transformerless FET input circuitry that can handle extreme dynamics with a maximum sound pressure level of 136 dB. So even if the featured performer at your next recording session or live show happens to be a revved-up jet engine, this workhorse mic will not distort!
Our C-2 mics also feature a low-frequency rolloff switch to eliminate infrasonics (mic handling noise, sound created by creaky stages), as well as a switchable -10 dB input pad to accommodate hot signals, such as a really loud vocalist or overzealous cellist.
You Are Covered
We always strive to provide the best possible Customer Experience. Our products are made in our own MUSIC Group factory using state-of-the-art automation, enhanced production workflows and quality assurance labs with the most sophisticated test equipment available in the world.
As a result, we have one of the lowest product failure rates in the industry, and we confidently back it up with a generous 3-Year Warranty program. |
- One-inch large-diaphragm, true condenser cardioid transducer
- Rugged all-metal body
- Roadworthy construction
- Switchable 20 dB preattenuation pad
- Switchable bass cut filter
- Legendary AKG sound quality
- Designed and engineered by AKG in Vienna, Austria
- Comes with spider-type shock mount and aluminium carrying case
The Perception 220 is a large-diaphragm true condenser microphone offering outstanding build quality and excellent value. Its many useful features and included accessories make this microphone uncommonly versatile. It delivers a classic warm, clear sound and conforms to the stringent standards defined for AKG recording products. These standards are based on AKG΄s six decades of experience in making microphones and on input from sound engineers around the world who use AKG products every day.
Its 1-inch large-diaphragm true condenser transducer brings AKG studio quality to the project studio as well as all other areas of recording and live sound applications. A switchable bass cut filter and preattenuation pad make it perfectly suited even for use on loud sound sources producing sound pressure levels up to 155 dB SPL. The rugged and roadworthy design makes it also a perfect choice for on-stage applications. The Perception 220 comes with a spider-type shock mount and a rugged metal case. |
Type |
1" Large Diaphragm True Condenser |
Polar pattern |
cardioid |
Frequency range |
20 to 20,000 Hz |
Sensitivity |
18 mV/Pa (-35 dBV) |
Max. SPL |
135 dB/155 dB (0/-20 dB) for 0.5% THD |
Equivalent noise level |
16 dB-A (IEC 60268-4) |
Signal/noise ratio (A-weighted) |
78 dB |
Preattenuation pad |
0 dB, -20 dB |
Bass filter |
12 dB/octave at 300 Hz |
Impedance |
=1000 ohms |
Current consumption |
|
|
| Behringer C-3 Dual-Diaphragm Studio Condenser Microphone
Introducing the Professional Condenser Microphone C-3 from BEHRINGER
Our latest dual-diaphragm condenser microphone C-3 is ideal for high-quality studio recording and live applications.
The selectable omnidirectional, cardioid, and figure-eight pickup patterns offer ultimate versatility needed to professionally record vocals and acoustic instruments. The C-3 holds a pressure-gradient transducer with a shock-mounted dual-diaphragm capsule. Its ultra-high sound resolution and flat frequency response rival those of microphones with much higher price tags. It also includes an LED that indicates phantom power operation and a gold-plated XLR output connector to ensure highest signal integrity. The C-3 comes with extensive accessories such as swivel stand and transport case.
The C-3 represents state-of-the-art technology at a price that is simply unheard of. |
Variable large diaphragm microphone | Pressure-gradient transducer with double membrane capsule | The studio microphone classic | Three directional characteristics: omni, cardioid, figure-8 | Switchable low frequency roll-off | Switchable 10 dB pre-attenuation |
Ideal as main and as support microphone in the most differing recording situations
Acoustical operating principle | Pressure gradient transducer | Directional pattern | Omnidirectional, cardioid, figure-8 plus | Frequency range | 20 Hz ... 20 kHz | Sensitivity at 1 kHz into 1 kohm | 20/28/22 mV/Pa1) | Rated impedance | 200 ohms | Rated load impedance | 1 kohms | Equivalent noise level, CCIR2) | 26/23/25 dB1) | Equivalent noise level, A-weighted2) | 15/12/14 dB-A1) | Signal-to-noise ratio, CCIR2) (rel. 94 dB SPL) | 68/71/69 dB1) | Signal-to-noise ratio, A-weighted2) (rel. 94 dB SPL) | 79/82/80 dB1) | Maximum SPL for THD 0.5%3) | 117 dB (cardioid) | Maximum SPL for THD 0.5% with preattenuation3) | 127 dB | Maximum output voltage | 390 mV | Dynamic range of the microphone amplifier (A-weighted) | 105 dB | Supply voltage (P48, IEC 61938) | 48 V ± 4 V | Current consumption (P48, IEC 61938) | 0.8 mA | Matching connectors | XLR3F | Weight | 500 g | Diameter | 56 mm | Length | 200 mm |
| |
NT2-A - ?The Legend Continues? Multi Pattern 1? Condenser Microphone.
The new NT2-A carries on the tradition forged by the now legendary R?DE NT2.
A professional large capsule (1?) studio microphone incorporating three-position
pick-up patterns, pad and high pass filter switches conveniently located on the
mic body.
At the heart of the NT2-A is the Australian designed and manufactured HF1 dual
diaphragm capsule. The frequency and transient response of this new transducer
has been voiced to complement today?s modern recording techniques, and yet still
evoke the silky smooth character of the legendary microphones of the 50?s and 60?s.
These features provide the flexibility and superlative audio characteristics that make
the NT2-A one of the most versatile condenser mics available.
The NT2-A?s variable controls allow switching between Omni, Figure 8, and Cardioid
polar patterns. The three position high-pass filter provides a flat response or an 80Hz
and 40Hz high pass filter to be selected. Finally the microphones Pad can be switched
between 0 dB, -5dB and -10dB. The NT2-A comes in a soft pouch with an M2 stand mount.
SPECIFICATIONS:
Features:
The Australian designed and manufactured HF1 1? edge terminated, gold sputtered, dual
5 um diaphragm capsule. 3-position variable polar pattern: Omni, Cardioid & Figure 8; all
controlled on the mic. 3-position variable high-pass filter: Flat, 80 Hz or 40 Hz. 3-position
variable pad: 0 dB, -5 dB or -10 dB. Ultra low noise, transformerless SMT circuitry. Wide
dynamic range. High strength heat-treated steel mesh head. Durable satin nickel finish.
Internal capsule shock mounting. Supplied complete with soft pouch and clip. Designed
and manufactured in Sydney, Australia.
Operation power:
The NT2-A is designed to operate from phantom power to the P48 standard. The NT2-A will
operate between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output
XLR connector.
Operation output impedance:
The NT2-A will operate satisfactorily into a load impedance as low as 1 kΩ. If a load below this
is used, the output signal level will be reduced. The NT2-A output is balanced between pin 2 (hot)
and pin 3 (cold). Pin 1 is ground.
Acoustic principle: Externally polarized 25 mm (1?) dual diaphragm.
Directional pattern: Multi-pattern
Frequency range: 20 Hz ~ 20 000 Hz
Output impedance: 200 Ω
Signal noise ratio din iec 651:
87 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 7 dBA SPL (per IEC651, IEC268-15)
Maximum spl:
147 dB (@ 1% THD into 1 kΩ); 157 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity: -36 dB re 1 Volt/Pascal; (16 mV @ 94 dB SPL) +/-2 dB
Dynamic range din iec 651: 140 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Output connection:
3 pin XLR, balanced output between; pin 2(+) and pin 3(-); Pin 1 ground
Weight with battery: 860 grm |
Acoustical operating principle | Pressure gradient transducer | Directional pattern | Omnidirectional, wide angle cardioid, cardioid, hypercardioid, figure-8 plus one intermediate position each | Frequency range | 20 Hz ... 20 kHz | Sensitivity at 1 kHz into 1 kohm | 34/47/62 mV/Pa* | Rated impedance | 50 ohms | Rated load impedance | 1000 ohms | Equivalent SPL CCIR 468-3 | 28/25/23 dB* | Equivalent SPL DIN/IEC 651 | 16/13/11 dB-A* | S/N ratio CCIR 468-3 | 66/69/71 dB* | S/N ratio DIN/IEC 651 | 78/81/83 dB* | Typical SPL (tube characteristic) | K | Maximum output voltage | 18 dBu | Dynamic range of the microphone amplifier cardioid DIN/IEC 651 for | 101 (121) dB | Powering | Power supply N 149 | Matching connectors | Microphone DIN 8F, Power supply XLR 3F | Weight | 730 g | Diameter | 70 mm | Length | 201 mm |
* Omnidirectional / cardioid / figure-8
|
Reviews
There are no reviews yet.