BEHRINGER MIC100 TUBE ULTRAGAIN VACUUM TUBE PREAMPLIFIER w-LIMIT

The PRE-73 DLX is a one-channel vintage style microphone-, line- and instrument preamplifier. The signal path uses only discrete components like resistors, capacitors and transistors. The line and microphone input and the line output are transformer balanced, using three different transformers, each one optimized for its purpose.
This is the way audio components were built before integrated circuits became available. The subjective sound quality delivered by vintage equipment is often prefered over the one delivered by modern units, a situation that is even more obvious now when music is recorded with clean-sounding digital audio equipment.

The circuit used in the PRE-73 DLX is similar to the preamp section in the classical 1073 module with a corresponding sound character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres. The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.

FEATURES

- Vintage Style electronics. No intergrated circuits in the signal path.
- Maximum gain on the mic input is 80 dB, enough to handle passive ribbon mics with quiet sound sources.
- Gain range on the Line input: -20 to + 10 dB.
- Switchable impedance on the mic input, 1200 or 300 Ohms, will change the tone of most mics.
- Switchable phantom power and absolute phase.
- A high-impedance instrument input for any sound module, electric guitar or bass.
- A simple but effective 4-step LED output level meter.
- The output level controls makes it possible to make fine gain adjustments and also to overload the main gain stage(s) for more character and then lower the signal to a suitable level before the output stage.
- Combo XLR/TRS input jacks and separate output XLR and TRS jacks for flexible connections.
- Insert jack for inserting EQ´s and other units.
- External high power power supply to avoid interaction with the audio circuits and transformers.
- A solid build quality that will last many years of normal use.

The PRE-73 DLX has a number of improvement and new features compared to the PRE-73 MKII:
- Tantalum capacitors in the signal path.
- Selectable 1073-style high pass filter, 50Hz, 80Hz, 160Hz and 300Hz.
- Output Attenuator -7, -14, -21 and -28 dB (located after the output transformer) allows overdriving the output stage and the output transformer for added character by lowering the output signal to a suitable level.
- The circuit board is prepared for Carnhill Mic and Line transformer and high pass inductor.
- The Insert jack can be switched in/out from the front panel. An internal jumper can select that the Insert jack always has an output signal.
- Switchable 600 ohm Output Termination and Ground Lift on the back panel.
- Selectable Active or Passive DI input and selectable input impedance in active mode, Hi Z or 100 kohm, by internal jumpers.
- The DI can signal can be selected to pass or bypass the mic input transformer by internal jumpers.
- Relays are used to control internal switching for DI input, Phantom power, Mic Low Z, Insert and Phase for shorter circuit board signal paths. The relays are controlled by front panel switches.
- Revised gain switch for added headroom.
- Circuit board star grounding scheme.
- Revised power supply with separate regulators for the audio circuits and relay and LED circuits.

The PRE-73 Mk2 pre-amp and the FC3 condenser microphone in one bundle. The bundle also includes Golden Age P1 Pop Filter, Proel RSM180 mic stand and Proel CHL250 5m cable.

The PRE-73 Mk2 is the first one-channel low-cost preamp on the market that is using a fully discrete signal path with three separate transformers for the balanced mic input, the line input and the output.

The circuit is very similar to the classical preamp section of the Neve 1073 pre/eq module with a corresponding sound character that is warm, punchy, sweet and musical.
This classical sound has been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.

The PRE-73 Mk2 has a maximum gain of 80 dB on the mic input and the gain range on the Line input is -20 to + 10 dB. There is also a high-impedance instrument input.

The PRE-73 Mk2 is perfect for almost any signal source, no matter if it's a microphone with a high or low sensitivity (like a passive ribbon mic), a syntheziser or sound module or an electric guitar or bass.

The input impedance of the microphone input can be switched between 300 and 1200 ohms, which makes it possible to affect the tone of most microphones. There is also phase switch and an simple 4-step LED signal level meter.

The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage for more character and then lower the signal to a suitable level before the output stage.

The Mk2 update consists of:
- An unbalanced insert jack (nominal level about 18 dBu) added on the back panel for inserting units like the coming GAP EQ-73, a three band eq.
-  LED meter levels adjusted.
- 600 Ohm termination resistor and jumper added to power supply board (accessible from the inside of the unit).
- Revised Gain switch, turning the know clockwise now increase the gain.
- Reduced noise at high gains by a change to the power supply grounding scheme.

Features
Superlative sound
Studio quality mic preamp
Total control - Input Gain, EQ contour, Output Gain,
Overload indicator
Multiple output connectors
XLR/jack combo input 
Switchable 48 V DC Phantom Power for condenser Mics
Compact, computer friendly package
Needs no external power supply
 
ARX is proud to introduce the e-pre - the ultimate microphone pre-amp for
hard disk recording, designed by audio professionals, not computer engineers.
The all-new e-pre is so much a part of your system that it fits right into a spare
5?" slot in your computer case! It's the perfect tool for all your day-to-day
recording requirements. No equipment racks to plug in, no masses of cabling to
connect - the e-pre is ready and waiting when you need it.
The e-pre is a studio quality microphone pre-amp using the same internal components
as high end mixing consoles, built into a compact, computer friendly package.
It has controls for:
Input Gain - fully variable from 10dB through to 60dB to suit all types of microphones,
plus switchable 48 V Phantom Power to enable condenser microphones to deliver
their best.
A Contour control for EQ sweetening, providing fast, easy access to a whole range
of useful EQ curves
Output level control - fully variable to match the e-pre's output to the input of the sound
card. From -10dB consumer cards through to +4dB for professional sound cards, the
e-pre can handle it.
Multiple output connectors match up with any kind of sound card, including mini jacks,
standard jack, RCA (phono) plugs, and even a connector to link to the internal CD ROM
audio input of your sound card (if fitted).
We've even fitted a 12 VDC input connector on the rear to enable the e-pre to run from an
external power supply if required (eg for use with notebook computers or stand-alone use).

Any way you look at it, the e-pre by ARX is the total professional microphone pre-amp for
all your hard disk recording needs

e-pre Benefits
Professional Balanced XLR mic input
True 48v phantom power
Runs into the Line input of ANY sound card - uses the card you've already paid for
High headroom = clean recordings
Smart EQ
Compatible with non-computer audio equipment
Professional performance and specs in a user friendly package
 

T E C H N I C A L  S P E C I F I C A T I O N S
Input Impedance
Mic 2 K Ohms Balanced; XLR type Pin 1 Audio Ground, Pin 2 +, Pin 3-
Line 25 K Ohms Balanced, ?" TRS jack Tip +, Ring , Sleeve Audio Ground
Phantom Power Voltage Switchable +48 V DC on XLR Pins 2 and 3
Max Input Level Mic +15 dB, Line +20 dB
Input Gain 10 dB Minimum, variable to 60 dB Maximum
Output Level -10 dB variable through 0 dB to +4 dB
Overload Indicator Measured at all Gain points throughout the circuitry
Output Noise -90 dB Unweighted, -97 dB 'A' weighted
(Measured with Gain nominal 20 dB, Output level -10 dB)
Frequency Response 20 - 20 KHz ± 0.25 dB
Distortion
100 Hz 0.0085%
1 KHz 0.008%
10 KHz 0.0083%
(Measured with Mic Gain 20 dB, Output 0 dB)
Power Requirements 12 V DC from either computer supply or external supply
(external power supply not included in e-pre package)
Size 148mmW x 42mmH x 150mm D (5?“W x 1?H x 6“D)
Weight Under 1 Kilo (2.2 lbs)