Content |
- High-end pre-amplification for all microphone, instrument and line-level sources. Specifically designed for studio-grade condenser mics
- Perfectly matches your studio, live and hard disk recording set-up
- Ultra-flexible Preamp Modeling allows you to optimize your recordings
- Choose between 16 preamp voicings designed for electric and acoustic guitars, keyboards, bass guitars, drums, vocals and more
- Built-in USB/Audio Interface to connect directly to your computer. Free audio recording, editing and podcasting software plus 150 instrument/effect plug-ins downloadable at behringer.com
- Powerful Phones output with Level control and Direct Monitor select
- Hand-selected 12AX7 vacuum tube with UTC technology for exceptional warmth and lowest noise
- Ensures outstanding signal transparency when used as a high-end DI-box
- Sophisticated output limiter prevents the output signal from clipping
- Dedicated low cut filter eliminates unwanted noise, e.g. floor rumble
- +48 V phantom power, Phase Reverse switch and 20 dB Pad for utmost flexibility
- Highly accurate 8-segment LED level meter
- Balanced inputs and outputs on ¼" TRS and XLR connectors
- Designed and engineered in Germany
|
Two channel classic Focusrite ISA transformer-based preamps Front panel, per channel: - 1/4" instrument input
- Variable input impedance - Low, ISA 110, Medium, High
- Input selection - Mic, Line, Instrument
- 0 - 30 dB/30 - 60 dB gain switch
- Phantom power switch
- Phase invert switch
- 0 - 60 dB gain in 10 dB steps
- 0 - +20 dB continuously variable trim
- Variable high-pass filter with on/off switch
- Insert point on/off switch
- Eight-LED user-calibrated level meters
- Single power switch
Rear panel, per channel: - XLR-F mic inputs
- 1/4" TRS line inputs
- 1/4" TRS Sends
- 1/4" TRS Returns
- XLR-M line output
- Single peak meter calibration dial
- Single IEC power socket
Measured Performance Maximum Input and Output Levels | Maximum Output Level |
+24 dBu with a THD+N
| Maximum Microphone Transformer Input Level | +7 dBu with a THD+N | Mic Input Response | Gain range | 0 dB to +60 dB in 10 dB steps, plus 0 dB to +20 dB continuously variable trim |
Input Impedance
| Switched Impedance setting
Equivalent Input Impedance at 1 kHz | Low = 600 Ω
ISA 110 = 1.4 kΩ
Med = 2.4 kΩ
High = 6.8 kΩ | EIN
(Equivalent Input Noise) | Measured at 60 dB of gain with 150 Ω
source impedance and 22 Hz-22 kHz band pass filter | -127 dB |
Noise
| Noise at output with unity gain (0 dB) and 22 Hz-22 kHz band pass filter | -97 dBu |
Signal-to-Noise Ratio
| Measured with 150 Ω source impedance and 22 Hz-22 kHz band pass filter | 121 dB relative to max output +24 dBu |
Total Harmonic Distortion + Noise
| Measured with a -20 dBu input signal at +30 dB of gain and with a 22 Hz-22 kHz band pass filter |
|
Frequency Response
| At minimum gain (0 dB) |
-0.5 dB at 10 Hz,
-1 dB at 135 kHz, relative to 1 kHz
|
At +60 dB gain
| -6 dB at 10 Hz,
-1 dB at 115 kHz, relative to 1 kHz |
CMRR (Common Mode Rejection Ratio)
| -94 dB for mic input at 60 Hz for max. output = +24 dBu
-91 dB for mic input at 10 kHz for max. output = +24 dBu |
Crosstalk Channel to Channel
| Mic input, with I/P = 0 dBu, gain = 0 dB @ 1 kHz input to channel A, channel B output = -85 dB | Line Input Response |
Gain Range
| -20 dB to +10 dB in 10 dB steps, plus 0 dB to +20 dB continuously variable trim |
Input Impedance
| 10 kΩ from 10 Hz to 200 kHz |
Noise
| Noise at main output with gain at unity (0 dB) measured with 50 Ω source impedance and a 22Hz - 22 kHz band pass filter |
-97 dBu
|
Signal-to-Noise Ratio
| Measured with 50 Ω source impedance and a 22 Hz-22 kHz band pass filter |
121 dB relative to max output +24 dBu
|
Total Harmonic Distortion + Noise
| Measured with a 0 dBu input signal, +10 dB of gain and a 22 Hz-22 kHz band pass filter |
|
Frequency Response
| At unity gain (0 dB) | -0.3 dB at 10 Hz,
-1 dB at 80 kHz, relative to 1 kHz |
Crosstalk Channel to Channel
| Line input, with I/P = 0 dBu, gain = 0dB
@ 1 kHz input to channel A |
Channel B output
= -91 dB
| Instrument Input Response |
Gain Range
| +10 dB to +40 dB continuously variable trim |
Input Impedance
| > 2 MΩ |
Noise
| >Measured with 22 Hz-22 kHz band pass filter | Minimum gain (+10 dB) = -95 dBu |
Frequency Response
| At minimum gain (+10 dB) |
-0.1 dB at 10 Hz,
-1 dB at 115 kHz, relative to 1 kHz
|
At maximum gain (+40 dB)
|
-2.5 dB at 10 Hz,
-1 dB at 110 kHz, relative to 1 kHz
| High-Pass Filter |
Roll-Off
| 18 dB per octave (3 pole filter) |
Frequency Range
| Continuously variable from 16 Hz to 420 Hz (-3 dB) | Weight and Dimensions |
W x D x H
| 480 mm x 280 mm x 44 mm |
Weight
| 3.7 kg |
|
The PRE-73 Mk2 is the first one-channel low-cost preamp on the market that is using a fully discrete signal path with three separate transformers for the balanced mic input, the line input and the output.
The circuit is very similar to the classical preamp section of the Neve 1073 pre/eq module with a corresponding sound character that is warm, punchy, sweet and musical.
This classical sound has been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.
The PRE-73 Mk2 has a maximum gain of 80 dB on the mic input and the gain range on the Line input is -20 to + 10 dB. There is also a high-impedance instrument input.
The PRE-73 Mk2 is perfect for almost any signal source, no matter if it's a microphone with a high or low sensitivity (like a passive ribbon mic), a syntheziser or sound module or an electric guitar or bass.
The input impedance of the microphone input can be switched between 300 and 1200 ohms, which makes it possible to affect the tone of most microphones. There is also phase switch and an simple 4-step LED signal level meter.
The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage for more character and then lower the signal to a suitable level before the output stage.
The Mk2 update consists of:
- An unbalanced insert jack (nominal level about 18 dBu) added on the back panel for inserting units like the coming GAP EQ-73, a three band eq.
- LED meter levels adjusted.
- 600 Ohm termination resistor and jumper added to power supply board (accessible from the inside of the unit).
- Revised Gain switch, turning the know clockwise now increase the gain.
- Reduced noise at high gains by a change to the power supply grounding scheme. |
- 1 microphone, XLR (bal.) or 6.3 mm jack (unbal.)
- Gain control, 10 steps (6-50 dB)
- Phantom power can be switched on
- Clip LED
- 1 line output, XLR (bal.) or 6.3 mm (unbal.)
- Operation via supplied power unit
Power supply: | 12 V DC, 150 mA | Input impedance: | 10 kohms bal./unbal. | Max. input level: | +4 dB bal./+10 dB unbal. | Gain: | 50 dB XLR/44 dB jack | T.H.D.: | 0.01 % | Frequency range: | 25 Hz - 16 kHz | S/N ratio: | >75 dB | Dimensions: | 143 x 93 x 45 mm | Weight: | 350 g |
| • Road proof housing
• High quality components
• Professional balanced XLR outputs
• Level control
The ASC-202 converts consumer level stereo RCA signals to balanced XLR professional line level, and back. One side of the unit, has two XLR inputs and stereo RCA outputs. The other side has stereo RCA inputs and two XLR outputs. Each side has stereo level controls. A possible application of the SC-13 is to use it as a level control in balanced audio lines.
The DAP Pro Audio Solutions are a complete line-up of audio tools for the professional musician or audio engineer. It is a series of audio modifying tools like mini-mixers, pre-amps and converters available in active or passive models. All audio solutions are designed to meet the highest stage and audio demands and feature a metal road proof housing with rubber feet and easy accessible controls. The units also have a small footprint which make them ideal to be used and placed in any environment where space is critical.
Specifications Frequency Response: 20Hz-20KHz
Inputs: XLR/Jack Combo, RCA
Outputs: XLR male, RCA
Input sensitivity RCA in: -10 dBv
Input Impedance RCA in: 10 kOhm
Input sensitivity XLR/Jack in: +4 dBu
Input Impedance XLR/Jack in: 20 kOhm
Output voltage RCA Out: -10 dBV
Output Impedance XLR Out: 100 Ohm
Output voltage XLR Out: +4 dBu
Output Impedance XLR Out: 200 Ohm
Power supply: 18V AC (adapter included)
Dimensions: 53 x 158 x 135 mm (HxWxD)
Weight: 0,65 Kg |
The U5 high-voltage DI-preamp combines a unique passive tone selector with a variable
gain preamp and filter. The high input impedance accepts a wide variety of signal levels
and instruments from acoustic guitars to high-output active bass guitars and keyboards.
The U5 direct box is loaded with sonic character and user features professionals demand.
U5 FEATURES
Pure Class A, 100% discrete design
Smooth musical detail and sonic excellence
Variable gain preamp to +30dB.
Dual microphone and line outputs
Hi-Z 3,000,000 ohm input impedance
Very low noise -100dB
High headroom +30dB
Six tone bank selections.
DC coupled Class A output for superior bass
High cut switch eliminates noise
LED active signal indicator
Headphone monitor output jack
Low distortion less than 0.5% THD and IMD
High level 400 watt speaker input
Active to thru selector - ground isolation switch
100% discrete power supplies for audio path
Internal toroidal power supply for low noise
Long lasting, stainless steel hardware
SONIC EXCELLENCE
The Avalon U5 Pure Class A instrument DI & preamplifier is the most powerful direct box
available today. Designed to optimize absolute signal integrity and musical performance,
the U5 includes many features and sonic excellence unequaled by lesser designs. The
U5 is ideal for bass guitar and acoustic instruments, electric guitars, keyboards, synthesizers
and low output pickups.
Features include state-of-the-art, high input impedance input stage for zero load effect on
sensitive pickups and keyboards, 100% discrete, Pure Class A signal amplifiers, practical
user features and rugged hardware designed to deliver true high performance audio for many
years.
DESIGNED FOR DEEP & CONTROLLED BASS
Avalon U5 DI-preamps have been in use around the world since 1995. They have found their way
into the world's leading musicians rigs and recording sessions and been featured on thousands
of the best selling (and sounding) albums and live performances.
MINIMUM SIGNAL PATH DESIGN
The U5 includes a variable gain Class A preamplifier to boost low level pickup signals and a high
level speaker input for capturing the live sound of the instruments amplifier. Six passive tone-EQ
curves are also included to enhance a variety of acoustic and electric instruments. A high-cut switch
eliminates unwanted acoustic pickup and high frequency noise, while a headphone monitor amp
has been included for personal listening. Twin DC coupled Class A output amplifiers drive both low
level microphone preamp inputs and high level +4dB inputs for direct to tape recording or processing.
The active-to-thru switch selects either the instrument input directly or sends the boosted-equalized
signal to the amplifier via the front panel jack. A ground isolation switch eliminates any possible earth
loop or AC buzz problems with complete safety.
U5 SPECIFICATIONS
Circuit Topology: 100% discrete, high-voltage Class A
Gain: Switched 3dB steps, maximum gain +30dB
Input Impedance: 3 ,000,000 ohm unbalanced (single ended)
Maximum Input Level +24dBu unbalanced, 400w speaker input
Output Connectors (2): XLR type, pin 2 hot electronic balanced
Maximum Output Level (Class A): +30dBu DC coupled, balanced 600 ohms (mic and line out)
Headphone Output: 0.5w into 600 ohms
Noise 20kHz Unweighted: -100dBu minimum gain position
Distortion THD, IMD: 0.1% at +10dB
Frequency Response, -/+0.5dB: 5Hz to 100kHz
Frequency Response, -3dB: 1Hz to 500kHz (input band limited)
High Cut Filter: -3dB at 8kHz minimum phase design
Tone Selector: Six position rotary switch, all passive filters
AC Power: Internal toroidal AC supply
Dimensions: 8.5 x 3.5 x 12 in (216 x 88 x 305mm)
Weight-Packed: 12lbs (5.4kg)
Rack mount kit (1) RM-1: Single U5 19 inch rack mount kit (holds one half rack unit)
Rack mount kit (2) RM-2: Dual U5 19 inch rack mount kit (holds two half rack units)
|
Reviews
There are no reviews yet.