BEHRINGER MIC500USB Preamplifier mic/line

• High-end pre-amplification for all microphone, instrument and line-level sources. Specifically designed for studio-grade condenser mics
• Perfectly matches your studio, live and hard disk recording set-up
• Ultra-flexible Preamp Modeling allows you to optimize your recordings
• Choose between 16 preamp voicings designed for electric and acoustic guitars, keyboards, bass guitars, drums, vocals and more
• Built-in USB/Audio Interface to connect directly to your computer. Free audio recording, editing and podcasting software plus 150 instrument/effect plug-ins downloadable at behringer.com
• Powerful Phones output with Level control and Direct Monitor select
• Hand-selected 12AX7 vacuum tube with UTC technology for exceptional warmth and lowest noise

• Ensures outstanding signal transparency when used as a high-end DI-box
• Sophisticated output limiter prevents the output signal from clipping
• Dedicated low cut filter eliminates unwanted noise, e.g. floor rumble
• +48 V phantom power, Phase Reverse switch and 20 dB Pad for utmost flexibility
• Highly accurate 8-segment LED level meter
• Balanced inputs and outputs on ¼" TRS and XLR connectors
• Designed and engineered in Germany

The PRE-73 DLX is a one-channel vintage style microphone-, line- and instrument preamplifier. The signal path uses only discrete components like resistors, capacitors and transistors. The line and microphone input and the line output are transformer balanced, using three different transformers, each one optimized for its purpose.
This is the way audio components were built before integrated circuits became available. The subjective sound quality delivered by vintage equipment is often prefered over the one delivered by modern units, a situation that is even more obvious now when music is recorded with clean-sounding digital audio equipment.

The circuit used in the PRE-73 DLX is similar to the preamp section in the classical 1073 module with a corresponding sound character that is warm, punchy, sweet and musical. These classic characteristics have been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres. The essence of this sound is now available at a surprisingly low cost, making it available to nearly everyone.

FEATURES

- Vintage Style electronics. No intergrated circuits in the signal path.
- Maximum gain on the mic input is 80 dB, enough to handle passive ribbon mics with quiet sound sources.
- Gain range on the Line input: -20 to + 10 dB.
- Switchable impedance on the mic input, 1200 or 300 Ohms, will change the tone of most mics.
- Switchable phantom power and absolute phase.
- A high-impedance instrument input for any sound module, electric guitar or bass.
- A simple but effective 4-step LED output level meter.
- The output level controls makes it possible to make fine gain adjustments and also to overload the main gain stage(s) for more character and then lower the signal to a suitable level before the output stage.
- Combo XLR/TRS input jacks and separate output XLR and TRS jacks for flexible connections.
- Insert jack for inserting EQ´s and other units.
- External high power power supply to avoid interaction with the audio circuits and transformers.
- A solid build quality that will last many years of normal use.

The PRE-73 DLX has a number of improvement and new features compared to the PRE-73 MKII:
- Tantalum capacitors in the signal path.
- Selectable 1073-style high pass filter, 50Hz, 80Hz, 160Hz and 300Hz.
- Output Attenuator -7, -14, -21 and -28 dB (located after the output transformer) allows overdriving the output stage and the output transformer for added character by lowering the output signal to a suitable level.
- The circuit board is prepared for Carnhill Mic and Line transformer and high pass inductor.
- The Insert jack can be switched in/out from the front panel. An internal jumper can select that the Insert jack always has an output signal.
- Switchable 600 ohm Output Termination and Ground Lift on the back panel.
- Selectable Active or Passive DI input and selectable input impedance in active mode, Hi Z or 100 kohm, by internal jumpers.
- The DI can signal can be selected to pass or bypass the mic input transformer by internal jumpers.
- Relays are used to control internal switching for DI input, Phantom power, Mic Low Z, Insert and Phase for shorter circuit board signal paths. The relays are controlled by front panel switches.
- Revised gain switch for added headroom.
- Circuit board star grounding scheme.
- Revised power supply with separate regulators for the audio circuits and relay and LED circuits.

The PRE-73 Mk2 is the first one-channel low-cost preamp on the market that is using a fully discrete signal path with three separate transformers for the balanced mic input, the line input and the output.

The circuit is very similar to the classical preamp section of the Neve 1073 pre/eq module with a corresponding sound character that is warm, punchy, sweet and musical.
This classical sound has been heard on countless recordings through the years and it is a versatile sound that works very well on most sound sources and in most genres.

The PRE-73 Mk2 has a maximum gain of 80 dB on the mic input and the gain range on the Line input is -20 to + 10 dB. There is also a high-impedance instrument input.

The PRE-73 Mk2 is perfect for almost any signal source, no matter if it's a microphone with a high or low sensitivity (like a passive ribbon mic), a syntheziser or sound module or an electric guitar or bass.

The input impedance of the microphone input can be switched between 300 and 1200 ohms, which makes it possible to affect the tone of most microphones. There is also phase switch and an simple 4-step LED signal level meter.

The output level control makes it possible to make fine gain adjustments and also to overload the main gain stage for more character and then lower the signal to a suitable level before the output stage.

The Mk2 update consists of:
- An unbalanced insert jack (nominal level about 18 dBu) added on the back panel for inserting units like the coming GAP EQ-73, a three band eq.
-  LED meter levels adjusted.
- 600 Ohm termination resistor and jumper added to power supply board (accessible from the inside of the unit).
- Revised Gain switch, turning the know clockwise now increase the gain.
- Reduced noise at high gains by a change to the power supply grounding scheme.

• Maximum of 66 dB of gain, in eleven discrete steps
• Dynamic range exceeding 120 dB
• 10 Hz to 50 kHz audio bandwidth
• High immunity to RF interference
• High current line output driver
• Transformer-balanced input and output
• Extended range peak limiter via dual opto-isolators makes preamplifier virtually "unclippable“
• Selectable 48-volt / 12-volt phantom power or 12-volt "T" power
• High-pass filter @ 80 or 160 Hz, 6 dB per octave
• Headphone monitoring of microphone audio, monitor audio, or a mix of both
• Monitor input accepts mono, balanced or unbalanced line-level inputs on 1/4-inch tip-ring-sleeve connector
• Separate level control of Monitor gain and overall headphone gain
• Split ear function via DIP switches
• Internal battery power (two-AA)
• Excellent battery life with alkaline and NiMH rechargeable batteries
• External 5-17 VDC powering (plug included)
• High-strength aluminum chassis with durable belt clip