| Content | BEHRINGER PM1 In ear monitor Volume Adjuster
- In-ear monitor belt-pack for personal monitor applications
- High quality volume control
- XLR input with locking mechanism
- 3.5 mm mini jack headphones connector
- Convenient belt-pack clip included
- "Built-like-a-tank“, impact-resistant metal chassis
- 3-Year Warranty Program*
- Designed and engineered in Germany
| Palmer Monicon, and the volume is right!
With Palmer Monicon, your monitor volume is always under control. The passive mini-mixer with the oversized control is inserted between the stereo output of the notebook, PC or interface and an active monitor system and thus permits convenient and precise volume control of the monitors from the workstation. The passive circuitry with only a few components has absolutely no affect on the sound. Mute and mono buttons make it possible to mute the outputs and merge the stereo output signal into a mono master signal.
The inputs and outputs of the controller are equipped with XLR connectors and the 3.5mm stereo TRS sockets usually found on computers. Combo input sockets also permit connection with 6.3 mm TRS plugs. Thus the Palmer Monicon is compatible with both professional and consumer equipment. Genuine wood sides make the practical studio tool in its massive powder-coated sheet steel housing an elegant looking "little helper" that is a typical Palmer product.
- Type: passive
- Number of channels: 2
- Number of inputs: 2
- Input connections: XLR Combo / 3.5mm stereo jack
- Input type: balanced/unbalanced
- Maximum input level: +20 dBu
- Input impedance: 10 kohms balanced/ 5 kohms unbalanced
- Number of outputs: 2
- Output connections: XLR/m, 3.5 mm stereo jack
- Output type: balanced/unbalanced
- Max output level: +20 dBu
- Output impedance: 600 ohms
- Frequency response: 10Hz - 40 kHz +/- 1 dB
- THD: 0,001 %
- Max. attenuation: 85 dB (attenuator), 112 dB (attenuator + mute)
- Controls: Attenuation, Mute, Mono
- Housing material: sheet steel/wood
- Housing surface: powder-coated
- Width: 164 mm
- Height: 62 mm
- Depth: 85 mm
|
Specifications
General
Frequency response
20 Hz - 20 kHz (+0 dB, -1.5 dB)
Signal-to-noise ratio
100 dB (IHF A-weighted, input level control min.)
Channel separation
80 dB between adjacent channels
Line input
Front: 6.3 mm jacks, unbalanced
Rear: RCA connectors, unbalanced
Input impedance
40 kOhm
Nominal level
-10 dBV (0.3 V)
Headphone outputs
four 6.3 mm stereo jacks
Maximum output power
2 x 1.5 W at 8 Ohm (1 channel in use)
2 x 1,2 W an 8 Ohm (four channels in use)
Power supply
230 V AC, 50 Hz
Power consumption
10 W
Dimensions (W x H x D)
482 mm x 44 mm x 196 mm
Weight
4 kg |
The amPlug Twin rolls back the years to capture the sound of the legendary clean American dual speaker combo tube amp. Noted for its sparkling and sustained clean sound, this amp has been is widely used in many genres - rock, blues, jazz, country, and more. Raising the gain provides a powerful American tube overdrive sound. A stereo chorus effect is built into the amPlug Twin, adding natural spaciousness and depth to the sound. As you play these sounds, you're sure to forget the passage of time, and lose yourself in the tones loved by musicians in styles such as jazz, country, and blues.
Specifications - Controls: Gain, Tone, Volume; STANDBY/ON/FX switch
- Terminals: PHONES Jack (stereo), AUX In Jack (stereo)
- Power supply: AAA batteries (x 2)
- Battery life: amPlug Twin (FX on):
- With zinc-carbon batteries: approximately 3 hours
- With alkaline batteries: approximately 11 hours
- Dimensions (W x D x H): 86 x 80 x 31mm/3.39" x 3.15" x 1.22“
- Weight: 40 g/1.41 oz. (not including batteries)
- Included items: AAA batteries (X2) (for verifying operation)
| The LD Systems HPA 1 is a versatile headphone amplifier with high power output for stage, studio and home recording and is the perfect solution for wired in-ear-monitoring.. The compact device in a rugged, ergonomically shaped plastic housing with soft-touch surface and practical belt clip is very extensively equipped.
In addition to locking XLR connectors for the stereo signal L/R input, the HPA 1 has a balanced 3.5 mm stereo jack as AUX input, which can be used in parallel for clicks or playback. It is protected for safe operation against excessive input levels; a hollow pin socket with negative internal contact enables the connection of a network adapter for fixed operation.
A 3.5 mm stereo jack is provided as earphone and headphone output. Volume level and balance can be set with easy-grip knobs, a push-button switches between the summed mono and stereo signals. A full-fledged limiter is integrated for distortion-free playback and as protection against feedback.
The LD Systems HPA 1 has bi-colour LEDs to facilitate the features overview, which displays the response of the limiter during peaks and the battery status. At 165 grams, the headphone amplifier is distinctly light-weight and can be operated for up to 12 hours thanks to a high quality 9 V block battery.
- Model Name: LDHPA1
- Product Type: headphone amplifier
- Type: 1-channel stereo
- Inputs: Main Input (Stereo), 1 x Aux In (Stereo)
- Input Connections: XLR-F (L + R Input, balanced), 3.5 mm stereo jack (Aux In)
- Input Impedance: 6 kOhm (XLR In), 10 kOhm (3.5 mm jack)
- Input Sensitivity: 3 dBu (XLR In), -6 dBV (3.5 mm jack)
- Max. Input Level: 16 dBu (XLR In), 7 dBV (3.5 mm jack)
- Protection Circuits: Audio Limiter, Max. Input leveling, Power OFF -Mute relay
- Headphone Outputs: 1
- Headphone Output Connectors: 3.5 mm stereo jack
- Power Output: 2 x 1.65 Vrms / 1% THD 33 Ohm Load
- Minimal Connected Impedance per Channel: 16 ohms
- Frequency Response: 20 Hz - 40,000 Hz
- THD 1 kHz Sine: 0.04%
- Controls: Power/Volume, Balance L/R, Stereo/Mono (Focus) switch,
- Indicators: Signal (Green) / Peak (Amber), Battery (low battery: red) / Power LED (Power ON: green)
- Power Supply: 9 V DC block battery, DC jack
- Operating Voltage: 9 V DC
- Power Consumption: Nom. 70 mA / Max. 150 mA
- Housing Material: plastic
- Housing Surface: soft-touch
- Housing Colour: black
- Width: 80 mm
- Height: 42.5 mm
- Depth: 133 mm
- Accessories (included): belt clip, 1 m 3.5 mm stereo jack cable
|
- Distributes the signal of 1 audio source to 4 sets of headphones
- 4 channels with separate level controls and headphone outputs
- All connections via 6.3 mm (1/4“) jacks
- Operation via supplied power unit
|
Reviews
There are no reviews yet.