Content |
Product Features: - High-end 24-bit/96 kHz A/D and D/A converter for ultimate signal integrity
- Converts any sample rate between 31 and 100 kHz into 32, 44.1, 48, 88.2 or 96 kHz sample rates
- Flexible format conversion between AES/EBU and S/PDIF (coaxial or optical)
- Universal sample rate synchronization via wordclock or digital input
- Allows parallel A/D and D/A conversion at identical sample rate
- Precise metering for input/output signal and headphone monitoring
- Allows direct manipulation of emphasis bits and other significant, digitally transmitted information in order to record virtually any audio signal
- High-precision quartz clock generator removes jitter and corrects off-tune, incorrect sample rates
- Extremely fast tracking supports varispeed applications
- Self-adjusting anti-aliasing filter with exceptionally steep edge
- All 3 outputs (XLR, RCA, Optical) simultaneously operational (splitter)
- Inputs separately selectable (patchbay functionality)
- High-quality components and exceptionally rugged construction ensure long life
|
The new Fostex HP-A3 is the perfect DAC for Computer Audio. This high quality unit features 32bit D/A Conversion with an integrated headphone amplifier exclusively designed to get the most from and PC audio set-up.
Why settle for 'built-in' D/A conversion when you can drastically improve the quality of your audio with a Fostex HP-A3?
32bit D/A Converter USB Bus power without using unwanted AC adapterWorks with up to 24bit/96kHz audio sourceHigh quality analog headphone amp to drive any type of headphonesEquipped with high-grade AKM 32bit DAC AK4390 - USB Bus power without using unwanted AC adapter
- Works with up to 24bit/96kHz audio source
- Exclusive PLL power supply is built in to reproduce the stable electrical supply
- High quality analog headphone amp to drive any type of headphones
- Equipped with hgih-grade AKM 32bit(*) DAC AK4390
- Condensers and OP amp designed exclusively for audio products
- USB / Digital (Optical) input selector
- Headphones / RCA (Analog) output selector
- Doubles as D/D converter from USB digital audio to Optical
- An USB/AC adapter from the shelf can be used for use as an Optical / Analog converter
Note: When using the USB input, the sampling frequency is fixed at 96kHz. Audio file with Fs 32k/44.1k/48kHz will be reproduced by upsampling to 96kHz and the S/PDIF Out is also fixed at 96kHz.
Input
USB port sampling frequency 16bit-24bit/96kHz
Interface: USB full speed
Digital Connector: optical, square
Format: S/PDIF (32kHz - 96kHz)
Output
Phones Connector: Stereo phone
Max Output: 100mW (32-ohm loaded)
THD: less than 0.01% at 1kHz, 32-ohm loaded, 100mW
Frequency response: 20Hz / 20kHz +-0.3dB (32ohm loaded, 100mW)
Analog Connector: RCA Pin
Reference output level -10dBV
THD: less than 0.01% at 1kHz
Frequency response: 20Hz / 20kHz +-0.3dB
Digital Connector: Optical, square
Format S/PDIF (32kHz - 96kHz)
General
Power: DC5V (via USB port)
Power Consumption: 2.5W
Accessories: 1 x USB cable (1.0m), 4 x rubber foot, manual
Dimensions: 108mm(W) x 36mm(H) x 140mm(D)
Weight: approx. 450g
|
The Tascam LA-40 MKIII has been primarily designed to provide matching capabilities between professional equipment and semi-professional or consumer equipment. It consists of four RCA inputs and outputs (–10 dBV, unbalanced) as well as four XLR inputs and outputs (+4 dBu/–20 dBu, balanced) which enable the user to connect for instance four tracks of a multitrack recorder (ins and outs) to a balanced mixer ensuring optimum level and impedance matching. Also, a switch matrix allows channels to be linked, utilizing the converter as a distribution amplifier for splitting signals to multiple recorders, or for multizone sound routing applications.
Switches on the bottom panel allow to select a nominal level of +4 dBu or –20 dBu for each channel and ±12 dB trim pots on the front panel make perfect level matching easy. LEDs on the front panel indicate signal presence for each channel. The LA-40 MKIII has also ground lift switches for each channel and a combined master switch to avoid ground loops.
Main Features
* 4 channels with unbalanced RCA inputs and balanced XLR outputs
* 4 channels with balanced XLR inputs and unbalanced RCA outputs
* XLR nominal level selectable between +4 dBu and –20 dBu
* Trim pots for each channel on front panel (±12 dB)
* Signal LED for each channel
* Ground lift switches for each channel and master switch
* Distribution amplifier functionality: One mono input signal can be routed to all four output channels, or one stereo input signal can be routed to two channels each (RCA to XLR and XLR to RCA)
* Internal power supply, no AC adapter needed
* 1 U rack-mountable chassis
Specifications
Inputs and outputs (unbalanced to balanced)
Inputs 4 RCA jacks (unbalanced)
Input impedance 23 kOhm (when all INPUT LINK switches are OFF)
5.7 kOhm (when all INPUT LINK switches are ON)
Nominal input level –10 dBV, ±1 dB
Maximum input level +4.8 dBV
Indicator detection level –36 dBV or more (OUTPUT LEVEL switch set to +4 dB or –20 dB)
Outputs 4 XLR-type connectors (balanced, Pin 1 = ground, Pin 2 = hot, Pin 3 = cold)
Output impedance 94 Ohm
Nominal load impedance 10 kOhm
Minimum load impedance 600 Ohm
Nominal output level +4 dBu, ±1 dB (OUTPUT LEVEL switch set to +4 dB)
–20 dBu, ±1 dB (OUTPUT LEVEL switch set to –20 dB)
Maximum output level +23 dBu
Inputs and Outputs (balanced to unbalanced)
Inputs 4 XLR-type connectors (balanced, Pin 1 = ground, Pin 2 = hot, Pin 3 = cold)
Input impedance 54 kOhm (when all INPUT LINK switches are OFF)
13.5 kOhm (when all INPUT LINK switches are ON)
Nominal input level +4 dBu, ±1 dB (INPUT LEVEL switch set to +4 dB)
–20 dBu, ±1 dB (INPUT LEVEL switch set to –20 dB)
Maximum input level +30 dBu (INPUT LEVEL switch set to +4 dB)
+8 dBu (INPUT LEVEL switch set to –20 dB)
Indicator detection level –22 dBV or more (INPUT LEVEL switch set to +4 dB)
–46 dBV or more (INPUT LEVEL switch set to –20 dB)
Outputs 4 RCA jacks (unbalanced)
Output impedance 200 Ohm
Nominal load impedance 10 kOhm
Minimum load impedance 1 kOhm
Nominal output level –10 dBV, ±1 dB
Maximum output level +18 dBV
Audio performance
TRIM range ±12 dB
S/N ratio (at nominal levels) 90 dB(A) (20 kHz LPF)
87 dB(A) (20 Hz HPF and 20 kHz LPF)
Total harmonic distortion
(1 kHz, at nominal levels) 0.005 % or less
Frequency response (at nominal levels) 20 Hz – 100 kHz, ±3 dB
Crosstalk
(1 kHz, nominal levels, 600 Ohm load) –90 dB
Other specifications
Power requirements 100–240 V AC, 50/60 Hz
Power consumption 6 W
Dimensions (W x H x D) 483 mm x 44 mm x 280 mm
Weight 3 kg
|
Inputs Analog Inputs 2 balanced inputs on 2 female XLR connectors Connect microphones via external mic preamps Connect guitars via DI boxes or external mic preamps Connect keyboards directly to Symphony I/O Digital Inputs AES IN: Stereo input on 1 female XLR connector Optical IN: Supports ADAT, SMUX & S/PDIF ADAT: 8 channels 44.1-48 kHz on 1 Toslink connector SMUX: 4 channels 88.2-96 kHz on 1 Toslink connector S/PDIF: 2 channels, up to 96 kHz on 1 Toslink connector S/PDIF Coax IN: 2 channels, up to 192 kHz on 1 RCA connector Outputs Analog Outputs 6 balanced outputs on 1 DSUB 25-pin connector Digital Outputs AES OUT: Stereo output on 1 male XLR connector Optical OUT: Supports ADAT, SMUX & S/PDIF ADAT: 8 channels 44.1-48 kHz on 1 Toslink connector SMUX: 4 channels 88.2-96 kHz on 1 Toslink connector S/PDIF: 2 channels, up to 96 kHz on 1 Toslink connector S/PDIF Coax OUT: 2 channels, up to 192 kHz on 1 RCA connector |
The Apogee AES-8-DIGI-IFC Multi-Channel Digital Cable System is an eight channel AES/EBU* input/output connection designed to interface the Apogee Rosetta 800 to a Digidesign 192's AES/EBU connection via DB-25 multipin connectors on both ends with metal shells for improved grounding and RF rejection. This cable provides 8 channels of AES input and output as per the AES standard. Thumb screws are 2.6mm. |
Input MADI: 1 x BNC, 1 x optical
Output MADI: 1 x BNC, 1 x optical
Input ADAT optical: 8 x TOSLINK, 24-Bit, Bitclock PLL
Output ADAT optical: 8 x TOSLINK, 24-Bit
Input word clock: BNC, Signal Adaptation Circuit (functional from 1.2 Vpp input signal), switchable termination
Output word clock: BNC, low-impedance driver stage, 4 Vpp into 75 Ohms, short-circuit-proof
MIDI input and output: via two 5-pin DIN jacks
Sync sources: MADI, ADAT optical, word clock, internal
Varipitch: by input signal or word clock
Sample rates: 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, variable (Sync/word clock)
Sample rate range: MADI: 32 kHz - 96 kHz, word clock: 27 kHz-105 kHz, ADAT: 33 kHz - 57 kHz
Jitter: Internal clock
Jitter suppression on external clock: circa 30 dB (2.4 kHz)
Jitter sensitivity: all PLLs operate even at 100 ns Jitter without problems
Power supply: internal switching mode ps, 100 V-240 V AC, 50-60 Hz, 10 Watts
Dimensions: 483 x 44 x 200 mm
|
Reviews
There are no reviews yet.