BEYERDYNAMIC Blueprint A150 Power Amplifier 2 x 150W USED

PRICE DOES NOT INCLUDE VAT

150W RMS into 8Ω (ohms)
1U slim fit rack mount design
High performance with incredibly low noise

Power Output Level:  QD4480                       

8ohm (Quad Ch)       80W    
4ohm (Quad Ch)       120W    
8ohm bridged mono   240W 

Input Sensitivity (8ohm, 1kHz)  0.775Vrms
Input Impedance 20kohm Balanced 
Slew Rate (8ohm, Full Swing) ±30V/?sec
Frequency Response (±0.5dB) 20kHz ~ 50kHz 
T.H.D. (f=20Hz~20kHz, Half Power) 0.03% 
Signal to Noise Ratio 105dB
Damping Factor (8ohm, 1kHz)  100
Rasidual Noise  -85dB
Channel Separation (8ohm, 1kHz)  80dB
Voltage Gain (4ohm)  26dB 29dB 32dB
Power Source  100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption  300W 420W 770W
Weight  11.5kg/25.3lb 15.5kg/34.2lb 17kg/37.5lb
Dimensions  482(W) x 88(H) x 369(D) mm
/19(W) x 3.5(H) x 14.5(D) in
 

XB Series - Intelligent Power

Power Without Compromises.
The XV is designed for paging, music and alarm signals. Versatile, dynamic and
extremely rugged according to IEC286-3. For the highest requirements in safety
and quality.
Sequential power on, alive contacts and incorporated ground fault detection -
the XV is the solution under all conditions. Without the need for additional equipment.
For uninterrupted and troublefree operation.
Needless to say that the Bittner High-End toroidal output transformers in the XV
series are some of the best available.

High Tech SMT Design
Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay
PHOENIX
High-End Toroidal Output 100V Transformers
Ground Fault Detection
LED Indicators for POWER, SIGNAL, CLIP, PROTECT, GNDFAULT
Temperature controlled, variable speed low noise fans
Volume Controls at the back
Stereo / Bridged / Parallel Mode
Softstart
Sequential Remote Power On
Alive Contact
Ground Lift
3 Years Warranty

TECHNICAL DATA:
XV 200:  2x 100 W / 100 V
Class:  AB
Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB)
THD:  < 0.07%
Signal-to-Noise Ratio:  < 101 dB
Channel Seperation:  > 70 dB
Input Sensitivity:  +6 dBu
Input Clipping:  22 dBu
Input Impedance:  20 kOhm
Cooling:  2 to 3 fans (temp. reg. variable speed)
Weight:  15 kg
Dimensions:  2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)

Power Output Level R-300 PLUS

STEREO
8ohm(T.H.D 0.05%)  170W+170W
4ohm(T.H.D 0.05%)  250W+250W

BRIDGED MONO
8ohm(T.H.D 0.05%)  460W
8ohm(T.H.D 0.5%)    500W

Frequency Response 20Hz- 20kHz, ±0.5dB

Convection Cooled

SoftStart Protection System

Balanced 10k&ohm;@0.775V Inputs