BLACKSTAR FS-10 Foot Controller

The FS-10 is a multi-function footcontroller that allows access to all 128 patches plus the tuner function. It operates in three modes: 
Patch Mode – This mode allows you to switch between the three banks of four patches accessible on the front panel of the amp (patches 1-12) in addition to patches 13-128, plus access to the tuner function and the ability to change to the other modes.

Effects mode – This offers individual switching of the effects within a patch, operating more like traditional effects pedals. In this mode the fourth switch is used to control the tap time function. 8.

Navigation mode – Enables access to the complete set of 128 patches stored on the amp. These can be stepped through one at a time, or in banks. Whilst in this mode you can also store patches.

Switch your signal between two different amplifiers, two different pedal boards or two different speaker cabinets. Flexible channel switching built into a compact die-cast case.

The Palmer TINO SYSTEM - The clever solution for switching two amps to 1 cabinet

Ambitious guitarists often use two amplifiers in order to obtain different basic sounds. However, transport, space restrictions and the decrease in output associated with PA speakers can be very inconvenient. This is where TINO SYSTEM promises to help. The switcher system allows you to use two amplifiers with only one box as an alternative. Regardless of whether you use tube amplifiers that require getting a load, or transistor models. Even a mixed combination is possible without any problems.

The switch-over between the amplifiers can be operated via a pressure switch on the device or via an optional standard foot switch or switching system. If the switch cannot be done with a switching system, a standard foot switch can be connected to the corresponding 6.3 mm jack. (Requires a switch, not push-buttons!)

TINO SYSTEM routes the guitar signal to the chosen amplifier, while the second unused amplifier is turned off to prevent unwanted interference. (As if the potentiometer on the guitar was switched off). The gain from the instrument input to output is one (Unity Gain). The built-in buffer only converts the impedance, so that a high-impedance guitar becomes less prone to interference. When the guitar signal is switched, the speaker is switched simultaneously, while the speaker output from the mute amplifier is connected to a load (Dummy Load). Therefore, tube amplifiers are absolutely safe from dangerous idling.

If you connect two amplifiers with one another, a heavy buzzing sound often overlays the guitar signal. This undesirable effect is known as ground loop and occurs between mains-operated devices because of double grounding. The TWO IN ONE prevents this from happening by decoupling the outputs to the amplifiers using high-quality isolating repeaters. A sliding switch-over between the amplifiers also ensures that the process occurs click-free and without interruption. The power supply is provided via the supplied 9V power adapter.

• Product Type: switcher
• Type: amp switcher
• Switching Functions: output switcher
• Number of Inputs: 2
• Input Connections: 6.3 mm jack
• Input Impedance: 10 M ohm
• Number of Outputs: 1
• Output Connections: 6.3 mm jack
• Output Impedance: 10 k ohms
• Transformer-Balanced Outputs: no
• Indicators: channel number
• Controls: channel switching, ground lift
• Power Supply: 9 VDC power adapter
• Power Consumption: 130 m A
• Cabinet Material: sheet steel/aluminium
• Cabinet Surface: powder coated/anodised
• Dimensions: 222 x 44 x 175 mm
• Accessories (included): 9VDC plug-in power supply

Designed to work with: ID:Core Stereo 20, ID:Core Stereo 40, ID:Core Stereo 40H and ID:Core BEAM, Connect a Blackstar FS-11 footcontroller (not supplied) to control your ID:Core in one of the following modes: In Alternative Mode (selected via INSIDER) patches will cycle on a ʻloopʼ. e.g. switching up from Bass 2 will move to Clean Warm. When in Manual Mode, the effect of any footcontroller switch will depend on its last state. Pressing Switch 1 will return the amplifier to Patch Mode. Pressing Switch 2 will toggle the effects off and on without returning to Patch Mode.

Dual footswitch with LED for Valve Reactor Series AC30VR & AC15VR, AC Custom Series AC15C1, AC30C2(X). Hi-quality durable all-metal construction with twin LED, separate stereo jack lead supplied for connect to amp.

 User's manual [1,27 MB]

The Palmer PEABI is more than a simple switcher for two sources; simultaneously, the PEABI also handles level adjustment for various sources. Whether microphone or line signal, the PEABI toggles silently between the two inputs and thus permits fast and simple comparison between signals or connection of various sources to one input. Three slide switches make it possible to select various attenuation levels (6, 15 or 21 dB attenuation) individually for both inputs. A ground lift helps to avoid ground loop hum. Housed in a solid metal case with extended edges for optimum protection of the in- and outputs. A red LED clearly indicates which input is currently active. Pre-drilled holes permit simple and secure mounting in a rack or on a pedal board. The PEABI's strictly passive circuitry means that it requires no power supply at all. A 9-volt block battery is required to power the LED.

• Product type: switcher
• Type: passive
• Switch function: Input switcher
• Number of channels: 2
• Number of Inputs: 2
• Input connections: XLR
• Number of outputs: 1
• Output connections: XLR
• Outputs transformer balanced: no
• Controls: Groundlift, Input PAD
• Indicators: Channel number
• Power Supply: 9-V block battery
• Case Material: Sheet steel
• Case surface: Powder coated
• Dimensions (W x H x D): 100 mm x 60 mm x 120 mm