BLACKSTAR FS-11 Footswitch

Designed to work with: ID:Core Stereo 20, ID:Core Stereo 40, ID:Core Stereo 40H and ID:Core BEAM, Connect a Blackstar FS-11 footcontroller (not supplied) to control your ID:Core in one of the following modes: In Alternative Mode (selected via INSIDER) patches will cycle on a ʻloopʼ. e.g. switching up from Bass 2 will move to Clean Warm. When in Manual Mode, the effect of any footcontroller switch will depend on its last state. Pressing Switch 1 will return the amplifier to Patch Mode. Pressing Switch 2 will toggle the effects off and on without returning to Patch Mode.

• Function on/off
• Without LED
• 5m cable
• Screwed steel housing
• Kink protection and cable feed-through
• Mono jack
• “Channel" label
• Suitable for all amplifiers with simple on/off switch
• Dimensions: 84 x 45 x 112 mm
• Compatible with: Marshall DSL50, DSL100, DSL401, EL34 50/50, EL34 100/100, EL84 20/20, MB30, MB60, MB150, G30RCD, G50RCD, G80RCD, G100RCD, JCM600, JCM601, JCM602, JTM612, JTM60, JTM622, JTM610, JTM615, MG30DFX, JTM312, JTM310, VS30R, 1962, 2555SL, 2100, 2500, 7400, 7200, 72115, 72410, 9100, 9200, 8040, 3520, 5522, 9004

• CRUSH 20 CRUSH 20RT & CRUSH 35RT (CHANNEL)
• CRUSH PRO SERIES (CHANNEL OR REVERB)
• TH30 AND TH100 (CHANNEL)
• DUAL TERROR (CHANNEL)
• AD30 (CHANNEL)
• OR 50 (MASTER VOLUME DEFEAT)
• CUSTOM SHOP 50 (EQ LIFT NOTE: THE LED WILL NOT ILLUMINATE AS THE CUSTOM SHOP USES PASSIVE SWITCHING CIRCUITRY)
• ROCKERVERB (REVERB OR CHANNEL)
• DUAL DARK (CHANNEL OR ATTENUATOR)
• OB1-300 & OB1-500 (BLEND CONTROL)

Don't feel like carrying around a full-sized foot controller? Now you don't have to! The FBV2™ lets you scroll through the first bank of four presets and is small and light enough to fit in your gig bag. With its ultra-reliable switches and aluminum case, the FBV2 can take all the abuse you can throw at it.

• Scrolls through Channels A,B,C, & D
• Self-powered though the locking cable

• Spider Valve
• Spider II
• Spider III
• Flextone III
• Vetta
• Vetta II
• HD 147
• Pod 2.0
• Pod XT
• Pod XT Pro
• Bass Pod XT
• Bass Pod XT Pro

The Palmer TINO SYSTEM - The clever solution for switching two amps to 1 cabinet

Ambitious guitarists often use two amplifiers in order to obtain different basic sounds. However, transport, space restrictions and the decrease in output associated with PA speakers can be very inconvenient. This is where TINO SYSTEM promises to help. The switcher system allows you to use two amplifiers with only one box as an alternative. Regardless of whether you use tube amplifiers that require getting a load, or transistor models. Even a mixed combination is possible without any problems.

The switch-over between the amplifiers can be operated via a pressure switch on the device or via an optional standard foot switch or switching system. If the switch cannot be done with a switching system, a standard foot switch can be connected to the corresponding 6.3 mm jack. (Requires a switch, not push-buttons!)

TINO SYSTEM routes the guitar signal to the chosen amplifier, while the second unused amplifier is turned off to prevent unwanted interference. (As if the potentiometer on the guitar was switched off). The gain from the instrument input to output is one (Unity Gain). The built-in buffer only converts the impedance, so that a high-impedance guitar becomes less prone to interference. When the guitar signal is switched, the speaker is switched simultaneously, while the speaker output from the mute amplifier is connected to a load (Dummy Load). Therefore, tube amplifiers are absolutely safe from dangerous idling.

If you connect two amplifiers with one another, a heavy buzzing sound often overlays the guitar signal. This undesirable effect is known as ground loop and occurs between mains-operated devices because of double grounding. The TWO IN ONE prevents this from happening by decoupling the outputs to the amplifiers using high-quality isolating repeaters. A sliding switch-over between the amplifiers also ensures that the process occurs click-free and without interruption. The power supply is provided via the supplied 9V power adapter.

• Product Type: switcher
• Type: amp switcher
• Switching Functions: output switcher
• Number of Inputs: 2
• Input Connections: 6.3 mm jack
• Input Impedance: 10 M ohm
• Number of Outputs: 1
• Output Connections: 6.3 mm jack
• Output Impedance: 10 k ohms
• Transformer-Balanced Outputs: no
• Indicators: channel number
• Controls: channel switching, ground lift
• Power Supply: 9 VDC power adapter
• Power Consumption: 130 m A
• Cabinet Material: sheet steel/aluminium
• Cabinet Surface: powder coated/anodised
• Dimensions: 222 x 44 x 175 mm
• Accessories (included): 9VDC plug-in power supply

Switch your signal between two different amplifiers, two different pedal boards or two different speaker cabinets. Flexible channel switching built into a compact die-cast case.