Content | The BLU-3 and BLU-6 wall panels are simple controllers which allow the designer to provide level control and source selection or preset recall in a simple wall-mounted panel.
These controllers connect to the control ports on the rear of any BLU-16, BLU-32 or BLU-80 device.
The BLU-3 offers a rotary fader and a five-way switch. The switch could select system presets (configurations specific to times of the day for example) while the rotary control could be assigned to act as a zone volume control.
The BLU-6 offers an eight-way switch, but instead of a rotary volume control has a pair of spin or up/down buttons, enabling the same level parameter to be mapped onto other controllers preventing a jump in audio level when the control is adjusted
The switches on both units have blank areas for marking the switch functions, either directly onto the white area, or on self-adhesive labels. |
| - SYSTEM POWER CONTROL You can control the power of your system by using this model. - AC AND DC POWER SUPPLY You can distribute AC and DC power through the AC outlet and DC terminals on the rear panel. - USE OF EMERGENCY POWER SUPPLY For emergency equipment power supply, an extra DC terminal is provided. - REMOTE CONTROL You can control the system power by remote control function even though the power switch on front is off. - AC AND DC VOLT METER This model uses digital volt meter displays of AC and DC. - OPERATING MODE DISPLAY You can easily check the operating mode by LEDs, AC or DC operating and emergency power. | | | | | PD-659 | AC Outlet | Switched 2000W ⅹ3 | Unswitched 700W ⅹ1 | Remote Control | 1 | DC Power Output | DC 24V 5A | Operation Temperature | -10℃~+40℃ | Power Source | 100-120VAC or 220-240VAC; 50/60Hz (Supplied ACmains transformer depends on country requirements) | Power Consumption | 190W | Weight(SET) | 6.2Kg/13.6Ib | Dimension(SET) | 482(W) x 88(H) x 380(D)mm/19(W) x 3.5(H) x 15(D)in | ※ Specifications and design subject to change without notice. | | | |
|
| - SYSTEM POWER CONTROL It controls the power of the rack system over all working together with the PD-659. - AC OUTLET TERMINAL To make the units using AC work, it has an AC outlet terminal for your convenience. AC switched group turn on and off repeatedly every 2 seconds. | | | | | PD- 658 | AC Outlet | Switched 2000W ⅹ3 | Operation Temperature | -10℃~+40℃ | Power Source | 100-120VAC or 220-240VAC; 50/60Hz (Supplied AC mains transformer depends on country requirements) | Power Consumption | 10W | Weight(SET) | 4.6Kg/10.1 Ib | Dimension(SET) | 482(W) x 88(H) x 380(D)mm/19(W) x 3.5(H) x 15(D)in | | | |
|
RM-200M - Five/ten zone console for VM-2120/2240 amplfiers
The RM-200M Remote Microphone that allows announcements to be made to any speaker zone and emergency announcements to all zones on a system with the VM-2120/2240 system management amplifiers.
These announcements can be made live or pre-recorded announcements
can be activated. The remote microphone is connected by cable to the
RM-210 Remote Microphone Extension unit.
SPECIFICATIONS:
Power Requirement | 24 V DC (12-30 V DC), (Supplied from VM-2120/VM-2240 Amplifier or local power suppy.) | Distortion | Less than 1% | Frequency Response | 100 - 10,000 Hz | Distortion | Less than 1% | Signal-to-Noise Ratio | More than 60 dB | Audio Output | 0 dB*1, 600 O, balanced | Microphone | Unidirectional electret condenser microphone, gooseneck type. | Speaker Zone Control | Zones 1-5 (Zones 1-10 with 2 stacked amplifiers) Groups 1-2, and All-Zone Broadcast | Emergency Broadcast | Activation of Emergency Broadcast (pre-recorded announcement*2 or live microphone announcement) by Emergency Switch | Voice Announcement Board Control | Activation of 5 messages*2 | Number of Connectable Units | Up to 4 | Communication System | RS-485 | Volume Control | Microphone volume control | Connection Cable and Connector Category | 5 STP cable, RJ45 connector | Communication Distance | 800 m maximum in total | Finish | ABS resin | Dimensions | 190 (W) × 75.7 (H) × 21.5 (D) mm (Gooseneck microphone excluded) |
| *1 0 dB = 1 V
*2 An optional EV-200 Board must be mounted in the VM-2120 or VM-2240 Amplifier. |
|
toa-at-100upr Build-in Attenuator with Relay
Toa - 100V installation
Build-in Attenuator with Relay 100 W / 100 V
|
The RM-210 is an extension unit for increasing the number of function keys of TOA's RM-200M, RM-200XF and RM-200X Remote Microphones.
Specification |
| Current Consumption | 20mA max. (in terms of RM-200M's DC power input 75mA max. (interms of DC power inputs of RM-200X and RM-200XF) | Connection | Connection to RM-200M, RM-200X or RM-200XF by way of dedicated Cable | Number of Function | Keys 10 | Function | When used to expand the RM-200M:
Selects and activates the Voice Announcement Board messages.
When used to expand the RM-200X and RM-200XF (PC software setting):
Emergency activation, emergency reset, BGM pattern selection, EV message activation, broadcast zone selection, monitor zone selection, chime activation, Talk switch activation, control output activation, input volume adjustment, zone volume adjustment, and failure output indication and reset. | Finish | ABS resin, bluish gray (PANTON 538 or its equivalent) | Dimensions | 110 (W) x 76.5 (H) x 215 (D)mm | Weight | 350g | Accessory | Extension cable x 1, Linkage bracket A x 1, Linkage bracket B x 1, Screw for linkage bracket x 12 |
|
Reviews
There are no reviews yet.