| Content |
Product Features - Extended upper clarity with smooth mid frequencies for any voice or instrument
- Hand-built proprietary large-diaphragm cardioid capsule for full, open sound
- High-pass filter and -20dB pad for ultimate versatility
- Works great with home studio USB audio interfaces
Technical Specifications
- Transducer Type: Condenser, Pressure Gradient
- Polar Patterns: Cardioid
- Frequency Response: 20Hz – 20kHz
- Sensitivity: 28.5 mV/Pa at 1 kHz (1 pa = 94 dB SPL)
- Output Impedance: 50 ohm
- Rate Load Impedance: Not less than 1k omh
- Maximum SPL: 138dB SPL (0.5%)
- S/N Ratio: 82.3 dB-A
- Noise Level: 11.7
- Dynamic Range: 126.3 dB
- Power Requirement: +48V DC Phantom Power
- Weight: 455g
- Dimensions: 222.5mm x 47.5mm
- HPF: 100Hz, 12db per octave
- PAD: -20dB
Includes Wooden storage box, Custom shockmount
|
MC10M is a multi capsule microphone set including a cardioid electret condenser microphone
(MC10) with the replaceable super cardioid capsule, shock mount adaptor, and wind screen.
MC10M can be used in wide applications, from studio & home recording to field sound aquisition.
FEATURES:
Replaceable 2 types of polar pattern capsule, cardioid/super cardioid as standard
Wide frequency response range
High sensitivity
Low distortion
High input withstand S.P.L.
Rugged brass case
Light weight
Shock mount adaptors, stereo mounting blacket & wind screen as standard
Dedicated carrying case as standard
SPECIFICATIONS:
Type :Back Electret
Condenser Microphone
Polar Pattern :Cardioid/Super Cardioid
Frequency Response :40Hz to 20kHz +/-10dB
Sensitivity :-40dBV/pa (10mv/pa)
Rated Impedance :200W
Equivalent Noise Level
:22dB (A weighted IEC/DIN 651)
Maximum S.P.L. :134dB (THD£0.5%, 1kHz)
Dynamic Range :112dB
Power Supply :48V Phantom Power
(IEC 268-15/DIN45596)
Current Consumption :3.5mA
Dimensions :?20mm x 150mm
Net Weight :130g (MC10 x 1)
Full Package Weight :865g
|
The R?DE NT6 is specifically designed for difficult mounting applications. Although
clearly relevant to instrument mic'ing, the new NT6 is extremely well suited to any
situation where a small 'unobtrusive' but powerful microphone system is required.
The NT6 utilises the 1/2" (externally biased) gold sputtered true condenser transducer
used in the internationally renowned R?DE NT5. The capsule is designed to attach to
a custom made, multi-position swivel mount allowing it to be independently positioned
with ease.
To further increase the versatility of the NT6, it is supplied with 2 thread adaptors - 1/4"
to 5/8" and 1/4" to 3/8" that enable the capsule assembly to be securely attached to a
wide variety of mic stands, tripods and boom poles.
The capsule is connected to the pre-amplifier (body) by a custom 3 m Kevlar? fibre reinforced
cable. Housed within the heavy duty satin-nickel-plated body, is a state-of-the-art low noise
balanced output preamplifier, exhibiting a wide dynamic range and full frequency response.
The surface-mount pre-amplifier circuit also incorporates a 2-position variable pad: 0 dB an -10 dB
attenuation, and a 2-position variable high-pass filter that enables you to step from a flat response
to 80 Hz high pass filter; both conveniently located away from the capsule, providing additional
control without the need to move the capsule once in position.
The NT6 is intended for Film, Television, Broadcast, Live Performance, Theatre, Television,
Surround and Environmental recording applications or wherever your imagination takes you.
The NT6 is produced in R?DE's design and manufacturing facility in Sydney, Australia. Utilising
state of the art computer controlled machining and assembly technologies, R?DE is able to
achieve levels of finish and repeatability of the most exacting standards and tolerances.
The NT6 comes supplied with Microphone Preamp (Body), Capsule, 3 m Kevlar? fibre reinforced
cable, RM5 Stand Mount, 2-axis Swivel Mount, 2 thread adaptors, ZP1 Zip Pouch and WS5 Wind Shield.
FEATURES:
? 1/2? (externally biased) gold sputtered true condenser capsule ? Heavy duty satin-nickel-plated body
? 2-position variable pad: 0 dB and -10 dB ? 2-position variable high-pass filter: flat and 80 Hz ? Surface
mount technology ? Low noise ? Wide dynamic range ? Full frequency response ? Supplied complete
with 2-axis swivel mount, 2 thread adaptors, M5 clip, WS5 (Black) Wind Shield and Soft Pouch ? Designed
& manufactured in Australia ? Full 2 year guarantee
Operation power:
The NT6 is designed to operate from phantom power to the P48 standard. The NT6 will operate
between 44V and 52V applied with positive polarity to pin 2 and pin 3 of the output XLR connector.
Operation output impedance:
Output Impedance: The NT6 will operate satisfactorily into a load impedance as low as 1 kΩ. If a
load below this is used, the output signal level will be reduced. The NT6 output is balanced between
pin 2 (hot) and pin 3 (cold). Pin 1 is ground.
Acoustic principle:
Externally polarised 1/2" (13mm) pressure gradient condenser
Directional pattern: Cardioid
Frequency range:
40 Hz ~ 20,000 Hz selectable HPF @ 80 Hz/12 dB/octave
Output impedance: 200 Ω
Signal noise ratio din iec 651:
75 dB (1 kHz rel 1 Pa; per IEC651, IEC268-15)
Equvalent noise: 19 dB SPL (per IEC651, IEC268-15)
Maximum spl:
138 dB (@ 1% THD into 1 kΩ)148 dB (@ 1% THD into 1 kΩ) - pad at maximum
Sensitivity:
-38 dB re 1 Volt/Pascal (16 mV @ 94 dB SPL) +/- 2 dB
Dynamic range din iec 651: 119 dB (per IEC651, IEC268-15)
Power supply voltage: 48 Volts (P48)
Weight: 386 grm.
Maximum output voltage: 6 dBu (@ 1% THD into 1 kΩ)
Pin assignment:
3 pin XLR, balanced output between pin 2(+), pin (-) & pin 1 (ground)
| NT3 - Versatile & Dependable
Stylish and modern, the NT3 is a studio and location workhorse. With both
48V phantom and internal 9V battery operation, this R?DE is at home anywhere.
Intended for studio, stage and location work, this versatile handheld or stand
mounted microphone incorporates a true externally polarized condenser (hyper-
cardioid polar response) transducer with an internal capsule shock mounting
system, and an ultra-low noise electronic circuit that has a high immunity to R.F.
interference. Incorporating a rugged welded and heat-treated mesh head and all
metal body. The NT3 is supplied in a zip pouch with a windshield, stand mount
and thread adaptor.
SPECIFICATIONS:
Acoustic principle: Externally polarised 19mm (3/4“) condenser
Directional pattern: Hypercardioid
Frequency range: 20Hz-20 kHz
Output impedance: 200?
Signal noise ratio din iec 651: > 77dB (per IEC268-15)
Equvalent noise: 123dB (per IEC268-15)
Power supply voltage: P48, P24, P12 phantom 9V battery
Weight without battery: 371g
Weight with battery: 680g | AKG C411L Ultralight Condenser Microphone
- Ultra-light vibration pickup
- Condenser transducer in sealed enclosure
- Cable with lockable miniature XLR connector
Weighing only 18 grams (0.6 oz.), this ultra-light condenser pickup is ideal for acoustic guitar, mandolin, violin, and most other stringed instruments. The C 411 will give a clear and uncolored sound without changing the balance of the instrument. Attaching the C 411 on or near the bridge or anywhere else on the instrument is easy with the included non-marring, reusable, solventfree adhesive compound.
C 411 L: With mini XLR connector for use with B 29 L battery operated power supply, MPA V L external phantom power adapter, or AKG WMS bodypack transmitters.
| Frequency range |
10 to 18,000 Hz |
| Max. SPL |
100 dB (for 1% THD) |
| Impedance |
200 ohms unbalanced |
| Recommended load impedance |
>=1000 ohms |
| Supply voltage |
9 to 52 V phantom power to DIN 45596 or battery powering from B 29 L or AKG bodypack transmitter |
| Current consumption |
approx. 2.2 mA |
| Connector |
C 411 L: 3-pin mini XLR |
| Cable |
C 411 L: 1.5 m (5 ft.) |
| Finish |
matte black |
| Dimensions |
27 x 14 x 9.5 mm / 1.1 x 0.5 x 0.3 in. |
| Net weight |
C 411 L: 18 g / 0.7 oz. |
| Shipping weight |
C 411 L: 150 g / 5.5 oz. |
|
The Stereo wonder. The new NT4, a visually striking microphone that solves
the age-old problem of stereo recording by eliminating the need to purchase
matched pairs and the associated complex set-up bars and adaptors to get
professional results. With a fixed 90 Deg. X/Y configuration and perfectly
matched stereo condenser capsules, the NT4 lets you record any source with
immaculate stereo detail.
The NT4 has a 128 dB dynamic range, 143 dBA SPL and low self-noise. Offering
selectable battery or phantom power operation with power indicator light, the NT4
is ideally suited to both studio and location recording.
The NT4 comes supplied in a custom carry case with a windshield, XLR to mini-jack
and dual XLR cables for portable DAT or professional balanced input connection.
SPECIFICATIONS:
Acoustic principle:
Stereo Microphone. 90° XY placement. Each side comprises an
externally polarised single diaphragm condenser transducer
Directional pattern: Cardioid per capsule
Frequency range: 20Hz - 20kHz
Output impedance: 200? per side
Signal noise ratio din iec 651: 78dB
Equvalent noise:128 dB
Power supply voltage:
P48 (38V?52V), P24 (20V-26V), P12 (10.8V-13.2V), 9V battery
Current consumption: 4 mA, 2 mA, 2.8 mA, 2.4mA
Weight without battery: 480g
Weight with battery: 2.3kg
|
Reviews
There are no reviews yet.