| Content |
Get some huge tube tone from the tiny Bugera T5 INFINIUM Guitar Amplifier Head. With this head weighing in at under 10 pounds, you can take it from silent headphone practicing in your apartment to the recording studio, or to your next club gig and plug it into a (separately available) cabinet. The simple single-channel design allows you to dial in your tone quickly, while the PHAT switch adds a gain boost and bypasses the EQ section for a more raw sound. Onboard reverb completes the package, adding subtle ambience or washy overtones to your sound.
Aesthetically, the T5 features a vented metal top which shows off the 12AX7 preamp and EL84 power amp tubes\' glow, along with the other amp components. An orange classic jewel status light shines when the power is on.
Classic All-Tube DesignThe T5 INFINIUM features Class-A technology with a 12AX7 front-end and an EL84 power stage. The tube design provides sweetly balanced harmonics and natural tube compression, resulting in the warm distortion and break-up you\'ve come to love from those vintage megaliths of yesteryear—in a portable and attractive chassis. The 12AX7 preamp tube can produce everything from soulful blues to mind-blowing crunch. Often employed in classic British-style amplifiers, the EL84 output tube is known for its crisp and chiming tonal quality. The built-in power attenuator can harness that power for reproducing a hard-working power amp tone at lower volume levels.INFINIUM TechnologyBy continuously monitoring the tube circuitry, INFINIUM lengthens tube life and keeps your tone consistent throughout the life of your tubes. When INFINIUM detects a change in tube operation due to aging or otherwise, it dynamically adjusts the circuitry so the tubes operate at their optimal load.
INFINIUM also knows when the power tube needs to be replaced and will illuminate an LED on the rear panel to notify you. Auto-Bias circuitry allows you to replace the tube without any esoteric or potentially dangerous adjustments that would require a trip to an amp tech.
Built-In ReverbT5\'s Reverb puts the finishing touch to your sound. Adjustable via the dedicated control on the front panel, you can dial in the level you desire—from a subtle touch to the cavernous, natural-sounding reverberation of a large arena.Power Attenuator and Speaker EmulationThe convenient, built-in Power Attenuator allows you to operate the T5 at your choice of 5 Watts, 1 Watt, or even 0.1 of a Watt, so you get everything from sweet and sassy to maximum tube saturation, even at reduced volume levels. The stereo headphone output has speaker emulation that tailors your tone for silent practicing.
| General |
|---|
| Dimensions (WxHxD) |
6.1 x 8.8 x 6.5“ / 155.0 x 223.0 x 165.0 mm Amplifier |
| Weight |
9 lb / 4.08 kg Amplifier |
| Amplifier Type |
Tube |
| Output Power |
5 W |
| Channels |
1 |
| Tube Types |
1 x Preamp 12AX7/ECC83
1 x Power EL84/6BQ5 |
| Output Impedance |
4 ohms Mono |
| Effects Loop |
No |
| Built-In Effects |
Digital Reverb |
| Master Volume |
Yes |
| Inputs |
1 x 1/4“ Mono Instrument |
| Outputs |
1 x 1/4“ Mono Speaker
1 x 1/4“ Stereo Headphone |
| Tone Section |
Bass, Gain, Treble |
|
The JVM Series 100-watt, valve-driven power stage is built on the classic design responsible for the legendary Marshall roar found in the JCM800, 2203 and "plexi" Super Lead amplifiers -- a timeless foundation for countless classic rock and metal guitar tones for over 4 decades. Featuring a quartet of EL34 valves, this peerless design has been expertly crafted to compliment the extraorinary wealth of tones found in the JVM.
Technical Info
Type: Head
Output (RMS): 100 watts
Channels: 4
Modes per Channel: 3
Independent Gain and Volume (per Ch): Yes
Independent Tone Network (per Ch): Yes
Independent Reverb Level (per Ch): Yes
Dual Programming Master Volumes: Yes
Silent Recording: Yes
Emulated Line Out XLR: Yes
Series FX Loop: Yes
Programmable Parallel/Series FX Loop: Yes
MIDI Presets: 128
Pre-Amp Valves: 4XECC83
Power Amp Valves: 1X ECC83, 4XEL34
6-way Programmable Footcontroller (Supplied) PEDL-00044
Dimensions (mm): 750 x 310 x 215
Weight (KG): 22
Speakers: No
|
The Marshall 2061X 20W Amp Head is a hand-wired reissue of the model 2061, a "Lead and Bass" head originally produced from 1967 to 1973. With 20W of power, it churned out golden crunchy tones with depth and character. The Marshall 2061X comes with 2 EL84 tubes in the power amp, 2 ECC83s in the preamp, and a solid state rectifier.
Marshall 2061X Handwired 20W Amp Head Features:
- Hand-wired reissue of the 2061 "Lead and Bass" head
- 20W
- 2 EL84 tubes in the power amp
- 2 ECC83s in the preamp
- Solid state rectifier
|
Marshall 50 Watt and 100 Watt, EL34 driven, valve power stages are, in the minds of many, the 'industry standard'. As soon as you hear Marshalls 50 Watt + 50 Watt, EL34 50/50 and the 100 Watt + 100 Watt, EL34 100/100 valve power amps, you will immediately understand why. Both of these eye catching units are packed with Marshall valve tone. Just like expensive hi-fi amps, both the EL34 50/50 and EL34 100/100 are Dual MonoBloc amplifiers - meaning that each side (channel) of the stereo amplifier operates as a completely independant unit. Each channel features its own Gain and Presence controls and our highly specialised 'True Differential Inverter' circuitry, ensures that the maximum integrity and pureness of their valve tone is maintained. Each channel also boasts a remotely switchable 'Voice' switch which takes you from 'traditional' (Voice A) to 'modern'(Voice B) and will allow you to cut through any mix, The Marshall EL34 50/50 and Marshall EL34 100/100 - professional, all-valve power amps that sound as good as they look!
| Palmer EINS - Amazingly versatile!
Small 1-5W amps have become very popular in recent years. They are fun items but some seem more like toys than real amplifiers.Palmers approach with the EINS was to design a serious true tube amplifier for professional purposes. The speaker simulated output allows you to connect the output of the amp directly to your audio interface. Thanks to the integrated loadbox aspeaker does not need to be connected. Thanks to the unique "HiZ output” you can connect the output of the EINS directly to the input of any amplifier! This way the EINS can be power boosted or used as a preamp or even on your pedalboard.
The Palmer EINS comes with an ECC83 preamp tube (V1) and an ECC82 (V2) power stage tube as standard. Other tube configurations are possible as follows.
- 1: V1:ECC83 - V2:ECC83: Quieter, distorts much faster, a little more gain, lead sound.
- 2: V1:ECC83 - V2:ECC81: Louder than Variation "1“, quieter than the standard configuration, more gain, distorts a little more quickly.
- 3: V1:ECC81 - V2:ECC82: Stays clean a little longer, a little more headroom, darker distortion sound.
- 4: V1:ECC81 - V2:ECC83: The quietest configuration, distortion sets in a little later than with Variation "1“, distortion can be controlled very precisely.
- Type: head
- technology: Tube
- class: A
- power: 1 W
- Inputs: 1
- input connectors: 6.3 mm Jack
- Input impedance: 1 M ohm
- outputs: 4
- output connectors: 6.3 mm Jack
- output impedance: Speaker out: 8 & 16 Ohm, Simulated out: 4k, HiZ out: 3,3M ohm
- Channels: 1
- Indicators: Power
- controls: Level, Tone
- FX loop: no
- Power supply: 230 VAC
- Power consumption: 10 W
- preamp tubes: ECC83
- power amp tubes: ECC82
- rectifier: solid state
- cabinet material: sheet steel
- Cabinet / Housing surface: powder coated / anodized
- width: 206 mm
- depth: 128 mm
- height: 108 mm
| The JVM Series from Marshall is the most comprehensive range of professional, all-valve amplifiers ever offered. No other multi-channel, multi-mode amplifier delivers the amazing all-valve tone offered by the JVM at any price. Multiple, all-valve voicings provide an amazing array of tones which are accessible from the front-panel switches, MIDI or via the revolutionary technology of the supplied footswitch. Hailed as a breakthrough in amplification by the worldʼs guitar press, the JVM Series offers a powerstage built on the peerless EL34 designs responsible for the legendary Marshall roar.
Outstanding Tone
The JVM Series uses a carefully designed, 4 x ECC83 pre-amp stage to generate the desired amount of gain, from the cleanest, yet complex, clean imaginable to a vast palette of overdrives that range from sophisticated and subtle to explosive and extreme. Boasting a truly amazing array of instantly switchable sounds, overflowing with harmonically rich tones and responsive fluidity, every JVM mode exudes that unmistakable Marshall sound and expands on it, effectively offering multiple Marshalls in one easy-to-use package.
Ultimate Flexibility
Each totally independent JVM channel offers three footswitchable modes which progressively add gain while offering a complimentary tonal topology, making the JVM the perfect amplifier for any situation.
Seamless, Silent Switching
Ultimate Control and Connectivity
Every JVM is supplied with a fully programmable footswitch. This revolutionary, patent-pending technology allows single front panel switching (SWITCH STORE) or entire set-ups (PRESET STORE – Channel/Mode, Reverb, FX Loop, Master Volume) to be simply assigned to any footswitch . . . or, even cooler, a mix ʽnʼ match of both modes. Housed in a rugged metal casing with blank panels on its surface which allow the user to label the pedal exactly as they want, the JVM pedal has no restrictive factory set-ups or functionality barriers, plus itʼs a breeze to program. The multi-coloured LEDs reflect every front panel switch status so you know exactly where you are, in the heat of a performance, without the need to glance at the amplifier itself.
The JVMʼs MIDI In and Thru connection means it can easily be integrated in a MIDI switching set-up, allowing you to store and recall 128 amplifier set-ups and enabling your MIDI effects board to easily control the amp. With its built-in memory and switching options the possibilities are endless!
Studio-Quality Reverb
Effective Control
Each JVM boasts two FX Loops that live on its rear panel. A footswitchable Parallel/Series Loop with Level and Mix controls plus a Series Loop with a Bypass switch. Combine the JVM with a MIDI FX processor and a MIDI footswitch and the skyʼs the limit!
The Tone of the Cone
In the case of the 2x12 in. JVM combos, after exhaustive testing of every speaker available, all agreed that the pairing of a Marshall/Celestion ʽHeritageʼ with a Marshall/Celestion ʽVintageʼ was the only way to go as the combination produces a fantastic depth and breadth of sound while maintaining a tight, musical response and a solid low-end thump. In the case of the 50 Watt 1x12”combo, a Celestion G12B delivers a full, wide sound that is much "bigger” than the JVM215Cʼs compact size would suggest.
Every JVM is made at the Marshall factory in the heart of England. Time-tested craftsmanship and construction are combined with the latest advances in manufacturing technology, ensuring world-class build quality and roadworthiness.
Internally, the JVM circuitry and layout has been kept as simple and logical as possible, ensuring the integrity of the guitar tone and an incredibly low noise-floor for such a high gain beast. Four, double-sided PCBs are used and connections are kept to a minimum to ensure maximum reliability. Only the best components are used to ensure very high quality and all of the internal wiring and amplifier assembly is performed by hand. Strict quality controls ensure every unit made is worthy of the world-renowned and respected white script Marshall logo. Meticulous valve selection adds further to the all-important tone and reliability that are both synonymous with the Marshall legend.
Technical Info
Output (RMS): 100 Watts
Speakers: No
Pre-amp Valves: 4 x ECC83
Power Amp Valves: 1 x ECC83, 4 x EL34
Footswitch (Supplied): PEDL-00045
Dimensions (Millimeters): 750 x 310 x 215
Weight: 22 kg, 48.5 lbs |
Reviews
There are no reviews yet.