| Content | MagicQ Software
MagicDMX is a low cost, single universe USB DMX interface created by ChamSys which contains an on board processor to process the DMX packets. Because all timing is done by the interface rather than relying on the host operating system, this ensures that the DMX timing is correct and consistent. MagicDMX connects to MagicQ running under Windows, Mac or Linux. It doesn\'t use any special drivers for the device, so you can just plug and play. MagicDMX defaults to outputing on Universe 1 from the MagicQ software but can be used on any universe.
MagicDMX has electrical protection for normal usage. Users requiring full optical isolation should consider the MagicQ Twin DMX Interface, the SnakeSys 4 Universe Ethernet Interface or any of the MagicQ Wing products which all have full optical isolation.
The MagicDMX interfaces do not unlock the restricted features of MagicQ software such as remote control via iOS/Android, audio input and full screen execute window. Users requring these features will need a ChamSys interface such as Twin DMX Interface, Mini Wing, PC Wing Compact or SnakeSys interface.
Note, MagicDMX interfaces to do remove the \'demo mode\' banner from MagicQ. The MagicDMX Full will output a single universe of DMX without any time restriction.
The MagicDMX Full interface is aimed at Professional users wishing to have uninterrupted DMX lighting control for shows and installations. The MagicDMX Full provides a great lighting troubleshooting system.
It can be configured to either output or input a single universe of DMX, but unlike the MagicDMX Basic interface, MagicDMX Full is not time limited and can be used continuously.
MagicDMX Full outputs DMX via a 5 pin female XLR connector. If you want to use the MagicDMX interface in DMX input mode a gender reverser is required.
MagicQ Software
MagicQ software offers powerful lighting control with loads of features that lighting designers have come to rely on, such as full lighting visualisation, pixel mapping, and HD media playback on up to 8 different layers, all integrated smoothly to streamline workflows, save time, and shorten learning curves on even the most complex lighting systems.
- MagicVis Visualiser
- Magic HD Pixel-Mapper
- Morphing
- Cloning
- Patch Offsetting
- Group and Palette FX
Download Software |
- Battery-powered WiFi to W-DMX™ converter
- Allows wireless lighting control via the Cameo iDMX® Controller App
- Receives WiFi signals from all iOS and Android devices
- 2.4 GHz W-DMX™ transmitter with an operating range of up to 300 m
- Can be used purely as a W-DMX™ transmitter via the DMX input
- Allows control of conventional DMX devices using the iDMX® Controller App via the DMX output
- Long-life LG Chem lithium-ion battery for reliable operation
- Battery management system prevents overcharging and deep discharging
- Includes power adapter charger, bag and DMX cable
Wireless lighting control at your fingertips using iOS and Android devices with the iDMX® CORE WiFi and W-DMX™ Box. The battery-powered unit is specially designed to work with Cameo\'s iDMX® Controller App. It features a 2.4 GHz W-DMX™ transmitter with an operating range of up to 300 m. 3 and 5-pin DMX inputs and outputs allow use with DMX light desks as well as wireless control of conventional DMX spots via W-DMX™ (the Wi-Fi connection is only between the mobile device and iDMX CORE). The high-capacity LG Chem lithium-ion battery provides up to eight hours of continuous operation for the iDMX® CORE Box, which can be extended by means of external power banks. An integrated battery management system prevents overcharging and deep discharging to ensure long battery life. A power adapter charger, DMX Y cable and bag are included.
Product type
LED PAR Lighting Accessories
Range of W-DMX™
up to 300 m
Range of WiFi
up to 15 m
Radio frequency
2400 MHz
DMX input
3-pin & 5-pin
Controls
On / Off , reset
Indicators
Status LED
Battery capacity
24 Wh
Charging time
6h
Battery operation time at maximum load
up to 8 hours
Housing material
Aluminium
Cabinet colour
Black
Protection class IP
20
Cooling
Convection
Maximum Ambient Temperature
-10° - 45° °C
Dimensions without mounting bracket
Width
85 mm
Height
25 mm
Length
170.5 mm
Weight
0,939 kg |
The Eurolite USB-DMX 512 interface combines very small dimensions with many functions due to the internal RISC-controller. This controller creates all DMX-signals so that the pc and the USB-port is not too busy enabling the parallel use of several DMX-universes.
Eurolite USB-DMX 512 Interface features:
- USB-DMX-Interface
- Interface between notebook or pc and DMX-devices
- Tested with the following DMX lighting control software: DMX-Configurator, FreeStyler, DMXControl
- Recommended system requirements: min. Pentium 3 processor 1GHz, 128 MB RAM
- Tested operating systems: Windows XP Home, Windows XP Professional, Windows Vista, Windows7
- Power supply: 5 V DC, 500 mA via USB
- Input: USB 1.1 / USB 2.0
- DMX-output: 512 channels
- DMX-512-connection: 3-pin XLR
| The Cameo CLSB83 is the professional solution for configuring DMX networks. The splitter and booster in 19" format amplifies the DMX input signal and distributes it to 8 electrically isolated outputs. It is connected directly to the DMX controller or to DMX devices. The input and the THRU socket for looping of the signal are duplicated on the front and back of the CLSB83 and connected in parallel. Bright LEDs show the DMX and power status of the channels on the front panel, the outputs are located on the back. A switchable 120 Ohm terminating resistor on the DMX THRU output and the power switch complete the equipment; the IEC-cable is supplied. For convenient output connector access and reverse installation the rack-mount angles can be attached to the rear of the chassis.
The Cameo DMX splitter and booster is also available in 5-pin design (art. No CLSB85).
- Type: DMX 512 protocol
- DMX Inputs: 2 (parallel)
- DMX Input Connectors: 3-pin XLR male
- DMX Thru Outputs: 2 (parallel)
- DMX Thru Output Connectors: 3-pin XLR female
- DMX Outputs: 8 (electrically isolated)
- DMX Output Connectors: 3-pin XLR female
- Controls: Power On/Off, DMX Thru Terminator
- Indicators: 8 x Power LED, 8 x Signal LED
- Power Socket: IEC power socket
- Power Supply: transformer
- Operating Voltage: 230 V AC, 50 Hz
- Power Consumption (max.): 15 W
- Dimensions (W x H x D): 483 x 44 x 160 mm
- Accessories included in package: power cord
|
- Professional 6-way DMX splitter / booster
- Chassis 1U 19" rack-mount enclosure
- 6 electrically isolated XLR (3-pin / 5-pin) outputs
- DMX status indicator per channel
- Power status indicator
- Switchable 120 Ohm terminating resistor for the DMX THRU output jack
- Front and rear rack-mount angle attachment options
The Cameo CLSB6D is the professional solution for configuring DMX networks. The splitter and booster in 19" format amplifies the DMX input signal and distributes it to 6 electrically isolated outputs. It is connected directly to the DMX controller or to DMX devices. The input and the THRU socket for looping of the signal are duplicated on the front and back of the CLSB6D and connected in parallel. Bright LEDs show the DMX and power status of the channels on the front panel, the outputs are located on the back. A switchable 120 Ohm terminating resistor on the DMX THRU output and the power switch complete the equipment; the IEC-cable is supplied. For convenient output connector access and reverse installation the rack-mount angles can be attached to the rear of the chassis.
Product type
Other Lighting Accessories
Type
DMX splitter / booster
DMX inputs
2 (parallel)
DMX input connectors
XLR 3-pin male , XLR 5-pin male
DMX Thru Outputs
2 (parallel)
DMX Thru Output Connectors
XLR 3-pin female , XLR 5-pin female
DMX outputs
6
Controls
DMX Thru Terminator , Power On/Off
Indicators
6 x Power LED , 6 x Signal LED
Mains connector
IEC power connector
Operating voltage
transformer
Operating voltage
230 V AC, 50 Hz
Power consumption
15 W
Width
483 mm
Height
44 mm
Depth
160 mm
Weight
2,976 kg
Accessories (included)
Power cord |
Work C 72 DMX
CD 72 DMX is a DMX to Analog signal converter suitable for 72 analog channels.
It converts DMX and MIDI signals into analog signals. It allows using an analog dimmer with DMX consoles, setting parameters like DMX start address channel, MIDI note selection, etc.
It also works as a chaser with adjustable speed to record and program scenes from a DMX console. With its Hold function, it provides memory against current failures that maintain the last DMX configuration.
C 72 DMX sends analog signals through SUB-25 connectors. Their input voltage can be set (from DC +10V, DC +15V or DC +20V) with DIP switches. Polarity can be switched too.
DMX to analog signal converter.
Adjustable voltage level for outputs (DC 10, 15, 20 V).
Voltage polarity selector.
72 channel chaser operating mode.
Programmable DMX start address channel.
Programmable chase speed.
Memory against current failures.
Main supply: 230 V AC 50 Hz.
Dimensions (WxHxD): 483 x 44 x 120 mm.
Weight: 2.3 kg.
|
Reviews
There are no reviews yet.