Content |
- Class D amp with Crown's ultra-efficient DriveCore technology weighs less than 11 lb (5 kg)
- Higher DSP capabilities: More control; has band pass filter per channel
- Increased lighting functionality; turn off all LED indicators except clip and thermal to reduce distraction in dark venues
- Selectable input sensitivity; 1.4Vrms and .775Vrms options so that amp can be driven at full power
- Set sleep mode after specified time without having to press a button
- Security setting disables menu buttons; menu locked/unlocked by entering combination
- System reset allows factory settings to be restored
- Remote power trigger
- Peakx™ Limiters provide maximum output while protecting your speakers
- XLR, 1/4“, RCA inputs provide flexibility
- Integrated PureBand™ Crossover System for better performance and control
- Efficient forced-air fans prevent excessive thermal buildup
Sensitivity |
1.4Vrms |
Frequency Response |
+0dB, -1dB |
Signal to Noise |
> 97dB (at .775Vrms sensitivity, 6dB lower) |
Intermodulation Distortion |
|
Damping Factor |
> 200 |
THD |
|
Crosstalk |
At 1kHz: > 85dB, At 20kHz: > 55dB |
Dimensions |
19" (48.3 cm) x 3.5" (8.9 cm) x 7.7" (19.6 cm) |
Weight |
8.6 lbs (3.9 kgs) |
|
XB Series - Intelligent Power
Power Without Compromises. The XB is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection- the XB is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX / Speakon LED Indicators for POWER, SIGNAL, CLIP, PROTECT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XB 400: 2x 200 W @ 4 Ohm Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.025% Signal-to-Noise Ratio: < 103 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: 500 @ 4 Ohm Cooling: 2x fan (temp. reg. variable speed) Weight:12 kg /(26 lbs) Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
Solid DYNACORD amplifier technology at highly competitive prices.
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 900 W, 4 Ω - 600 W, 8 Ω - 380 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1700 W, 4 Ω - 950 W, 8 Ω - 480 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1800 W, 8 Ω - 1200 W Input Sensitivity, rated power @ 8 Ω, 1 kHz +3.1 dBu (1.11 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 14.8 kg (32.6 lbs)
|
- Output Power:
500W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
330W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
- Bridge Mode, Mono 820W RMS @ 8 Ohms, 1K Hz, 1% THD
- Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
- Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
- Slew Rate: 15V Per usec
- Damping Factor: @ 8 Ohm: 300
- Impedance: 20 Ohms balanced / 10 Ohms unbalanced
- Cooling System: 2 individual fans
- Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift; Limiter
- build in clip limiter
- Input: XLR 3pin + Jack 6,3mm
- output: Speakon + Binding post
- Dimensions (LxWxH): 360 x 482 x 88mm 2-rack mount spaces
- Weight: 15 KG.
|
These amplifiers offer high, stable power output and a high efficiency factor on the high performance level and are therefore the ideal choice for driving a multitude of mobile and club systems. SL series power amplifiers are equipped with a comprehensive protection package and dynamic limiters.
The integrated, switchable Low-Pass Notch filter (a typical DYNACORD special feature) corrects the frequency response and optimizes the transient behaviour of loudspeakers.
Maximum Midband Output Power, THD = 1%, 1 kHz, Dual Channel 2 Ω - 650 W, 4 Ω - 450 W, 8 Ω - 270 W Maximum Single Channel Output Power, Dynamic-Headroom, IHF-A 2 Ω - 1150 W, 4 Ω - 660 W, 8 Ω - 350 W Maximum Bridged Output Power, THD = 1%, 1 kHz 4 Ω - 1300 W, 8 Ω - 900 W Input Sensitivity, rated power @ 8 Ω, 1 kHz + 2,2 dBu (1,0 Vrms) Maximum Input Level +21 dBu (8.69 Vrms) Voltage Gain, ref. 1 kHz 32.0 dB Frequency Response, ref. 1 kHz 10 Hz...40 kHz (±1 dB) Output Stage Topology Class AB Dimensions (W x H x D), mm 483 x 88.1 x 421.5 Weight 12.6 kg (27.8 lbs)
|
Power Output Level R-150 PLUS
STEREO
8ohm(T.H.D 0.05%) 50W+50W
4ohm(T.H.D 0.05%) 75W+75W
BRIDGED MONO
8ohm(T.H.D 0.05%) 50W
8ohm(T.H.D 0.5%) 170W
Frequency Response 20Hz- 20kHz, ±0.5dB
Convection Cooled
SoftStart Protection System
Balanced 10kΩ@0.775V Inputs
|
Reviews
There are no reviews yet.