Content |
The Crown® Macro-Tech® i Series continues the Macro-Tech legacy of unparalleled sonic accuracy and detail, putting sound quality above all else
Patented, cutting-edge Class-I circuitry gets more power out of an amplifier with less waste
Rugged construction ensures that all Macro-Techs are built to withstand years of abuse on the road
Global Power Supply — designed to deliver maximum power no matter what country you work in
Built-in load, line voltage, input and output monitoring
Standard Ethernet networking via System Architect® lets system operators monitor and control the amplifier from any location
Performance
Frequency Response (at 1 watt, 20Hz - 20 kHz into 8 ohms) ± 0.25 dB
Signal to Noise Ratio below rated full-bandwidth power,
A-weighted > 108 dB
Total Harmonic Distortion (THD) at 1 watt into 8 ohms
Total Harmonic Distortion (THD) Plus Noise at full rated power
Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from full rated output to –30 dB
Damping Factor (20 Hz to 100 Hz at 8 ohms) > 5000
Crosstalk (below rated power, 20 Hz to 1 kHz) > 80 dB
Common Mode Rejection (CMR) (20 Hz to 1 kHz) > 55 dB, typically > 70 dB
DC Output Offset (Shorted input)
Input Impedance (nominal) 10 kilohms balanced, 5 kilohms unbalanced
Maximum Input Level +20 dBu typical
Load Impedance (Note: Safe with all types of loads)
Stereo: 1/2/4/8/16 ohms Bridge Mono: 2/4/8 ohms
Input Sensitivity (referenced to 8 ohm rated output) 1.4V, 32 dB gain, and 26 dB gain
Voltage Gain (referenced to 8 ohm rated output) MAi-5000i:
37.1 dB to 22.2 dB MAi-9000i:
37.9 dB to 23.0 dB MAi-12000i:
39.3 dB to 24.5 dB
Required AC Mains Universal AC input, 100-240VAC , 50/60 Hz (±15%). Maximum AC mains voltage 264VAC.
AC Line Connector Five cordsets supplied with amplifier (USA, UK, European, Australia, India)
Construction
Cooling Dual-zone, microprocessor controlled, continuously variable speed fans,
front-to-back airflow
Front Panel Cast aluminum with integrated handles.
Weight 28 pounds (12.7 kg) net, 36 pounds (16.3 kg) shipping.
Dimensions (W x H x D) 19 in. (48.3 cm) W x 3.5 in. (8.9 cm) H x 16.2 in. (41.1 cm) D.
Protection Amplifier is protected against reactive loads, faults and shorts. If one channel experiences a catastrophic failure, the entire amplifier will shut down.
4-ohm Dual (per ch): 4,000W
8-ohm Dual (per ch): 2,100W
4-ohm Bridge: 7,000W
8-ohm Bridge: 8,000W
|
High-tech in professional amplification!
The fP 2400Q is a lightweight and space-saving four-channel power amplifier, ideal for use in high quality touring sound systems as well as in demanding permanent installations. The fP 2400Q offers a diverse choice of applications, such as: multi-channel monitor systems, four-channel reproduction, and compact amplification in active 2-, 3-, and 4-way systems. The fP 2400Q makes possibile the bridge connection of one or two of the two pairs of channels (channel A and B and/or channel C and D). It also features Lab.gruppen?s unique power matching solution, the MLS switch, which offers endless combinations for solving most of the problems related to varying impedances and maximum power capacities of loudspeakers. The latest semiconductor technology is utilized in the new ferrite Power (fP) amplifiers. This, together with Lab.gruppen?s proprietary copper cooling system, Intercooler?, enhances the 2 ohms capacity. Two easily accessible dust filters on the front ensure a clean front-to-rear airflow. Additionally, a new Bi-phase wiring scheme also increases the capacity of the switch mode power supply. This extends the power bandwidth in the low end.
Key Features: 4 x 370 watts @ 8 ? 4 x 380 watts @ 4 ? 4 x 500 watts @ 2 ? (Measured just below clip level, with all 4 channels driven) Light weight and compact: only 8.6 kg (19lbs), 2U high MLS? Switch: Lab.gruppen?s unique power matching for different loads
New Features: Replaces the LAB 1200C Easily accessible dust filters Improved low-end power bandwidth Extruded front panel for increased stability
Besides the traditionally superb Lab.gruppen sonic performance, there is a full line of features to make the fP family functional in all situations from installation to high performance live sound systems:
Regulated switch mode power supply Today there are many lightweight, switch-mode amplifiers in the market. However, the unique Lab.gruppen switch-mode power supply technology offers a number of essential advantages that make it superior to other and seemingly similar power supply designs. The most important features are the regulated power supply and the extreme power efficiency. The regulated power supply easily deals with a very high variation in the AC mains voltage: it can drop by up to 20% below its nominal level - e.g. to 180 V instead of 230 V ? without any problem. Perhaps even greater benefits result from the extreme efficiency of Lab.gruppen amplifiers: only a fraction of the energy from the AC mains is turned into heat. A regulated power supply also presents some other sonic advantages, such as better cone control and the same fast response as a conventional power supply.
Sophisticated protection circuitry, combining: ALS? short circuit protection; the Adaptive Limiting System permits very high peak currents, but keeps the amplifier within the Safe Operation Area DC protection; protects against infrasonic signals VHF protection; protects the loudspeakers against strong very high frequency non-musical signals above the audible range Thermal protection; prevents the amplifier from being overheated. The protection indicators on the front panel are switched on, as a warning, before the protection process is initiated AC protection; shuts down the power supply if the line voltage is outside the operating voltage Clip limiter; prevents severely clipped waveforms from reaching the loudspeakers, whilst maintaining full peak power. |
Power Output Level R-300 PLUS
STEREO
8ohm(T.H.D 0.05%) 170W+170W
4ohm(T.H.D 0.05%) 250W+250W
BRIDGED MONO
8ohm(T.H.D 0.05%) 460W
8ohm(T.H.D 0.5%) 500W
Frequency Response 20Hz- 20kHz, ±0.5dB
Convection Cooled
SoftStart Protection System
Balanced 10kΩ@0.775V Inputs
|
BASIC Series - Intelligent Power
BASIC - that's meeting the tightest budgets and professional requirements in reliability, flexibility and sound. Alone or in combination with the other products of the Bittner portfolio. The consequent realisation of the Bittner quality standards indicates once more our understanding of the contracting business. It underlines our philosophy that cost consciousness has nothing to do with giving up standards. Compromise is a word unknown to Bittner Audio! The incorporation of detent potentiometers, clip limiter, protection circuits for any imaginable situation, as well as a first-class production process using only highest-quality components made the BASIC series the choice of most contractors.
Certainly more than basic!
High Tech SMT design Excellent sound and superior impulse response Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay XLR Inputs Speakon and Binding Posts Clip Limiter Toroidal transformers LED Indicators for SIGNAL, CLIP, PROTECT, POWER Temperature controlled, variable speed, low noise fans Detent potentiometers Stereo / Bridged / Parallel Mode Ground Lift Robust Steel Chassis 3 Year Warranty
TECHNICAL DATA: Basic 800: 2x 400 W @ 4 Ohm Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.03% Signal-to-Noise Ratio: < -102 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: > 400 @ 4 Ohm Cooling: 2x Fan (temp. reg. variable speed) Weight: 13 kg. Dimensions : 2 RU/483x89x265 mm (19" x 3.5" x 12.6“)
|
Power Output Level: QD4480
8ohm (Quad Ch) 80W
4ohm (Quad Ch) 120W
8ohm bridged mono 240W
Input Sensitivity (8ohm, 1kHz) 0.775Vrms
Input Impedance 20kohm Balanced
Slew Rate (8ohm, Full Swing) ±30V/?sec
Frequency Response (±0.5dB) 20kHz ~ 50kHz
T.H.D. (f=20Hz~20kHz, Half Power) 0.03%
Signal to Noise Ratio 105dB
Damping Factor (8ohm, 1kHz) 100
Rasidual Noise -85dB
Channel Separation (8ohm, 1kHz) 80dB
Voltage Gain (4ohm) 26dB 29dB 32dB
Power Source 100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption 300W 420W 770W
Weight 11.5kg/25.3lb 15.5kg/34.2lb 17kg/37.5lb
Dimensions 482(W) x 88(H) x 369(D) mm
/19(W) x 3.5(H) x 14.5(D) in
| Power Output Level QD4960 :
8ohm (Quad Ch) 170W
4ohm (Quad Ch) 240W
8ohm bridged mono 480W
Input Sensitivity (8ohm, 1kHz) 0.775Vrms
Input Impedance 20kohm Balanced
Slew Rate (8ohm, Full Swing) ±30V/?sec
Frequency Response (±0.5dB) 20kHz ~ 50kHz
T.H.D. (f=20Hz~20kHz, Half Power) 0.03%
Signal to Noise Ratio 105dB
Damping Factor (8ohm, 1kHz) 100
Rasidual Noise -85dB
Channel Separation (8ohm, 1kHz) 80dB
Voltage Gain (4ohm) 26dB 29dB 32dB
Power Source 100-120VAC or 220-240VAC ; 50/60Hz
(supplied AC mains transformer depends on country requirements)
Power Consumption 300W 420W 770W
Weight 11.5kg/25.3lb 15.5kg/34.2lb 17kg/37.5lb
Dimensions 482(W) x 88(H) x 369(D) mm
/19(W) x 3.5(H) x 14.5(D) in |
Reviews
There are no reviews yet.