Content |
The XLC2800 Power Amplifier is compact, powerful and cost-effective with ease of installation, outstanding sound quality and the unwavering reliability inherent in every Crown product.
- Power for 2 ohm, 4 ohm and 8 ohm outputs, supporting stereo, parallel and bridge outputs.
- Support parallel connection of cinema surround speaker.
- Indicators provide accurate diagnostics: Power, Signal, Clip and Fault.
- Volume control on rear panel.
- Input configuration: Stereo and parallel
- Output configuration: Stereo and bridge
- HD-15 and phoenix connectors make the system wiring easy.
- High performance, light weight class-D amplifier - weights less than 12 lbs / 5kg (net weight).
Model Number XLC2800
Product Type Power Amplifier
Compatible Speakers JBL 3722(N), 4722(N), 3730, 3252(N), 4641, 4642A, 8320, 4181, 8281, 8340A, 8350, SCS8, SCS12
Compatible Monitors Crown Monitor and Crossover System CXM2000 for monitor, fault detection and crossover functions
Crown Monitor System DSi-8M for monitor function
Stereo (all channels driven) Specifications
2-ohms 1200W
4-ohms 775W/800W*
8-ohms 440W
Bridge Specifications
4-ohms 2400W
8-ohms 1550W
Amplifier Performance Specifications
AC Line Voltage and Frequency, Configurations Available (+/-10%) 100VAC 50/60Hz, 110VAC 60Hz, 220/230~240VAC 50Hz
Voltage Gain 42
Sensitivity (for full rated power at 4 ohms) 1.4V
Signal-to-Noise Ratio (ref. rated power, 8 ohms, 1kHz) >103dB
Total Harmonic Distortion (THD) (1kHz) 200
Intermodulation Distortion (IMD) (60Hz ~ 7kHz, 4:1, from full rated output to -30dB) 85dB
Crosstalk (below rated 8 ohms power) At 20kHz >55dB
Input Impedance (nominal) 20 kilohms balanced; 10 kilohms unbalanced
Load Impedance 2~8 ohms per channel in Stereo; 4~8 ohms in Bridge
Dimensions Specifications
Width x Height x Depth 19 in. (48.3 cm) x 3.5 in. (8.9 cm) x 10.4 in. (26.4 cm)
Net Weight 10.4 lbs (4.72 kg)
Shipping Weight 13.2 lbs (6 kg)
|
- Signal to Noise (20 Hz - 20 kHz): 100 dB - Input Sensitivity: 1.2 Vrms - Voltage Gain (8 Ohms): 34.4 dB - Output Circuitry: 2-tier Class H - Power Requirements: 6A - Frequency Response: 20 Hz - 20 kHz, +0, 1 dB - Dynamic Headroom (4 Ohms): 2 dB - Damping Factor: 100 - Input Impedance: Greater than 20k (balanced) - Maximum Input Level: +24 dB (16 Vrms) - Input Connectors (each channel): 3-pin XLR and 1/4-inch TRS, balanced, parallel Phono, unbalanced - Output Connectors (each channel): Speakon, 1/4-inch, Binding Posts - Amplifier and Load Protection: Short circuit, open circuit, thermal, RF protection Load protected against DC faults - Rear Panel Controls: Full Range / Crossover switch - Dimensions (H x W x D): 3.5 x 19 x 10.1 inches (89 mm x 483 mm x 257 mm) - Weight: 26 lbs (12 kg) Front Panel Controls and Indicators: - Gain controls, 21 detents - Red Clip LEDs, proportional, 0.1% THD threshold - Green Signal LEDs, threshold -35 dB - Blue Power LED, AC on Stereo Mode: - 8 Ohms / both channels driven: 500 Watts - 8 Ohms / single channel driven: 600 Watts - 4 Ohms / both channels driven: 700 Watts - 4 Ohms / single channel driven: 850 Watts Distortion: - 8 Ohms: less than 0.05% - 4 Ohms: less than 0.1% Dimensions and Weight in Packaging Shipping Weight: 31 lbs Shipping Dimensions: 24 x 15 x 7 in
| Crown XTi2002 Specifications:
* Output Power 2 ohms Stereo (per ch): 1000W
* Output Power 4 ohms Stereo (per ch): 800W
* Output Power 8 ohms Stereo (per ch): 475W
* Output Power 8 ohms Bridged-Mono: 1600W
* Output Power 4 ohms Bridged-Mono: 2000W
* Sensitivity (for full rated power at 4 ohms): 1.4 Vrms
* Frequency Response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB
* Signal-to-Noise Ratio (below rated 1kHz power at 8 ohms): 100 dB (A weighted)
* Total Harmonic Distortion (THD):
* Damping Factor 20 Hz to 1 kHz: > 500
* Crosstalk (below rated power): 20 kHz - 1 kHz: > 70 db
* Input Impedance (nominal): 20k ohms balanced, 10k ohms unbalanced
* Maximum Input Signal: +22 dBu typical
* Operating Temperature: 0°C to 40°C at 95% relative humidity (non-condensing)
* Level Control: Two front-panel rotary level controls, one for each channel
* Power Switch Control: On/Off switch applies AC power to the amplifier
* Sel/Prev/Next Buttons Controls: Three buttons near the LCD screen that are used to access menu items and front panel lockout
* LCD Screen: Backlit liquid crystal display that shows preset and processing status
* Signal Indicator: Green LED, one per channel, illuminates when a very low-level signal is present at input (may be used for troubleshooting cable runs).
* –10 Indicator: Green LED flashes when output signal exceeds -10 dB below clip.
* –20 Indicator: Green LED flashes when output signal level exceeds -20 dB below clip.
* Ready Indicator: Green LED, one per channel, illuminates when the amplifier is ready to produce audio.
* Clip Indicator: Red LED, one per channel, turns on at the threshold of audible distortion
* Temp Indicator: Red LED, one per channel, illuminates under excessive temperature conditions
* Power Indicator: Blue LED illuminates when the amplifier has been turned on and has power
* Input Connectors: XLR, one per channel
* Link/Out Connector: Loop-thru signal from input connector for linking another amplifier, one per channel.
* Output Connectors: Two Neutrik Speakon NL4MP output connectors. Channel-1 Speakon is wired with Ch. 1 and Ch. 2 outputs for use with optional single 4-conductor cable. Two binding post outputs (in parallel with Speakon® connectors).
* HiQnet™ USB Connector: Type B, connects to HiQnet™ network.
* Chassis: Steel
* Front Panel: Cast-aluminum
* Cooling: Proportional speed fan with front-to-rear airflow.
* Dimensions: 19" (W) x 3.5" (H) x 12.25" (D)
* Net Weight: 18.5 lbs (8.4kg)
* Shipping Weight: 21.5 lbs (9.8kg) |
A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N
Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange,
and superbly defined highs. They also deliver fast response and exceptional stability even in the face
of serious power supply limitations. Refinements throughout this expanded five-model lineup make
these amplifiers the new benchmarks for quality, reliability, and versatility in professional applications.
Frequency Response: 10 Hz – 40 KHz. Output Power: 2 x 400 Watt / 8Ω RMS, 2 x 700 Watt / 4Ω RMS,
1400 Watt / 8Ω bridge RMS. Weight: 13 Kg. |
XR Series - Intelligent Power New Horizons.
A lightweight with enormous power output. Combined with digital signal processing. That's what we call flexibility! Locally controlled or completely networked. No matter what the requirements are. The integrated powerful digital signal processor (DSP) and controller allows for a troublefree and easy adjustment to any acoustical environment. Wear-free digital potentiometers, sequential remote power on, alive contacts for easy supervision, computer controlled monitoring - its enless list of useful feature make it the right choice for any installation. XR - the new definition of Intelligent Power
High Tech SMT Design Digital Signal Processor Excellent sound and superior impulse response Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX / Speakon High-End Switched Power Supply with Power Factor Correction (not XR4000) LED Indicators for SIGNAL, CLIP, PROTECT, POWER Temperature controlled, variable speed low noise fans Digital wear-free Volume Controls (can be operated manually) Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Paging Input Monitor Output SXL Dataport Perfect Weight-to-Power ratio 3 Years Warranty
Technical Data: XR 2000: 2x 1400 W @ 2 Ohm 2x 1000 W @ 4 Ohm Class: H Frequency Response:20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.02% Signal-to-Noise Ratio: < -106 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: 750 to 1200 @ 4 Ohm Cooling: 4 Fans (temp. reg. variable speed) Weight: 8 kg Dimensions: 2 RU / 483 x 88 x 454 mm(19" x 3.5" x 17.9“) |
Crownʼs new CTs series of power amplifiers are remarkable for their loud, punchy sound; sustained, tight bass; and superior protection against overheating and overload. This paper explains the design features behind those advantages. After reading this information, youʼll know why Crown CTs amps sound better than the competition. CTs amplifiers can provide large amounts of power into various loads, such as 2, 4, 8 ohms and 70V. With most power amps, the maximum output power tends to drop as the load impedance increases. But with the CTs series, the power stays the same at almost any impedance. 2-ohm Dual (per Ch.) 250W 4-ohm Dual (per Ch.) 600W 8-ohm Dual (per Ch.) 600W 16-ohm Dual (per Ch.) 300W 70V Dual (per Ch.) 600W 4-ohm Bridge 500W 8-ohm Bridge 1200W 16-ohm Bridge 1200W 140V Bridge 1200W Crown switching power supply for less weight Sustained Power on long-duration signals due to regulated, "stiff” power supplies with incredible energy storage (huge filter capacitors). Extra Hidden Power during high-level transients and during incomplete use of all the channels. Overheating and overload protection thanks to the sophisticated TLC circuitry which compresses the signal only when needed. Compression is controlled not by temperature, but by signal voltage. This keeps the loudness up during compression more than with competitive amps. |
Reviews
There are no reviews yet.