| Content | Crown XLI 800
The Crown XLI 800 is a reasonably priced but robust and powerful power amplifier. It ideally suits the use in budget-oriented applications at both mobile and stationary areas. It offers a power of 2 x 300 Watts at 4 Ohms. Thereby, the integrated fan guarantees a high operating safety, due to the constant airstream for cooling the power amplifier. The XLI 800 offers a robust an analogue circuit, which is supplied by a conventional power supply. Furthermore it owns three different, selectable modes (stereo, bridge and parallel).
Crown XLI 800:
- Reasonably priced, robust and powerful power amplifier
- Robust and analogue circuit
- LED display for each channel for signal, clip and error
- Stereo, bridge and parallel modes
- Conventional power supply
- Performance: 2 x 200 Watts / 8 Ohms, 2 x 300 Watts / 4 Ohms
- Inputs: Cinch, XLR
- Outputs: 2 x speakon, spring clip
- Robust 19 inch housing
- Height: 2 U
Specifications
|
XLi800 |
XLi1500 |
XLi2500 |
XLi3500 |
| Channels |
2 |
2 |
2 |
2 |
| Sensitivity (full rated power at 8 ohms) |
0.775V or 1.4V |
0.775V or 1.4V |
0.775V or 1.4V |
0.775V or 1.4V |
| Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted) |
> 100 dB |
> 100 dB |
> 100 dB |
> 100 dB |
| Total Harmonic Distortion (THD) (20Hz - 20kHz) |
|
|
|
|
| Inter Modulation Distortion (60Hz and 7kHz at 4:1 from full rated output to -40 dB) |
= / |
= / |
= / |
= / |
| Frequency Response (at 1W, 20Hz - 20kHz) |
0 dB, -1 dB |
0 dB, -1 dB |
0 dB, -1 dB |
0 dB, -1 dB |
| Crosstalk (below rated power) |
at 1kHz: -75 dB |
at 1kHz: -75 dB |
at 1kHz: -75 dB |
at 1kHz: -75 dB |
| at 20kHz: - 59 dB |
at 20kHz: - 59 dB |
at 20kHz: - 59 dB |
at 20kHz: - 59 dB |
| Damping Factor (from 10Hz to 400Hz, 8 ohms) |
> 200 |
> 200 |
> 200 |
> 200 |
| AC Line Voltage and Frequency Configurations (± 10%) |
120VAC 60Hz |
120VAC 60Hz |
120VAC 60Hz |
120VAC 60Hz |
| 220VAC 50/60Hz |
220VAC 50/60Hz |
220VAC 50/60Hz |
220VAC 50/60Hz |
| 230-240VAC 50/60Hz |
230-240VAC 50/60Hz |
230-240VAC 50/60Hz |
230-240VAC 50/60Hz |
|
|
|
|
|
| Dimensions (H x W x D) |
3.5" x 19" x 12.4“ |
3.5" x 19" x 12.4“ |
3.5" x 19" x 12.4“ |
3.5" x 19" x 14.4“ |
| (89 x 482 x 315mm) |
(89 x 482 x 315mm) |
(89 x 482 x 315mm) |
(89 x 482 x 366mm) |
| Net Weight |
25.1 lb (11.4 kg) |
28.0 lb (12.7 kg) |
29.7 lb (13.5 kg) |
43.0 lb (19.5 kg) |
| Net Shipping Weight |
29.5 lb (13.4 kg) |
32.4 lb (14.7 kg) |
34.2 lb (15.5 kg) |
47.4 lb (21.5 kg) |
| L1400 450W-450W 4ohm (280W-280W8ohm)
COMPACT MODERN DESIGN
Compact size (2U-Rack Height) with up to 1200W per channel@2ohms
these amps save valuable rack space without compromising power output.
HIGH CURRENT TOROIDAL TRANSFORMER
A high-current toroidal transformer saves rack space
and minimizes hum and noise.
EXCELLENT SOUND QUALITY
The low T.H.D.(0.05%) and high damping factor (400 or higher)
gives excellent sound quality.
2 STAGE POWER SUPPLY
The high-power units (L1800 and L2400) have a 2-Stage Class-H design
that maximizes their performance.
EQUIPPED WITH 30Hz or 50Hz HPF
All amplifiers are equipped with high-pass filters on each channel to
help maintain sound quality, yet help protect the loudspeakers.
EXTENSIVE PROTECTION CIRCUITS
Extensive protection circuits monitor over voltage/current conditions, overheating,
output shorts, and DC voltage to improve performance and reliability.
CLIP-LIMITER CIRCUITS
Clip-limiters on each channel are provided to help prevent
distortion due to excessive signal levels.
L.E.D FUNCTION DISPLAYS
Power, Clip limiter, Signal, Protection, Mode (Parallel/Stereo/Bridged)
LEDs on the front panel indicate the status of the unit in operation. |
VLP Series Power Amplifier
Output Power:
- 150W RMS Per Channel @ 4 Ohms, 1kHz, 0.1% THD
- 100W RMS Per Channel @ 8 Ohms, 1kHz, 0.1% THD
(Bridge Mode, Mono)
- 300W RMS @ 8 Ohms, 1K Hz, 1% THD
Total Harmonic Distortion: Less Than 0.1% (20Hz - 20kHz @ 8 Ohms)
Frequency Response: (+/-01db, @rated output Power, 8 Ohms): 20Hz - 20K Hz
Slew Rate: 15V Per usec
Damping Factor @ 8 Ohm: 260
Impedance: 20 Ohms balanced / 10 Ohms unbalanced
Cooling System: 2 indivdual fans
Special Features: High/Low Pass Filter / Input Sensitivity Selector / Ground Lift
Dimensions (LxWxH): 13.25" x 19" x 1.75" / 336 x 482 x 44mm (1-rack mount space)
Weight: 24 lbs. / 11Kgs.
Special Features: High/Low Pass Filter; Input Sensitivity Selector; Ground Lift
|
Engineered from the ground up for unmatched quality and performance,
the Crown? DSi Series of power amplifiers offers three models of 500W,
800W, and 1200W per channel at 4 ohms. Onboard digital signal processing
includes crossovers, EQ filters, delay and output limiting. Rear panel HD-15
connector provides easy input/output connectivity between DSi amplifiers
and the new DSi-8M System Monitor.
The intuitive front panel LCD screen guides installers through a setup process?
featuring presets for the industry-standard JBL cinema loudspeaker systems?
to make configuration quick and easy.
At the touch of a button, Crown?s DSi cinema amplifiers deliver perfectly matched
performance with each award-winning JBL ScreenArray? system, making this the
ultimate cinema solution.
Features :
Includes three models of 500W, 800W, and 1200W per channel at 4 ohms
Automatic presets for popular JBL cinema speaker systems for quick, easy
configuration
Intuitive front-panel LCD screen guides installers through setup
Onboard digital signal processing includes crossovers, EQ filters, delay, and
output limiting
Computer connectivity via USB allows fast setup and configuration with HiQnet?
System Architect? software
Rear-panel HD-15 connector provides easy input/output connectivity between DSi
amplifiers and new DSi-8M System Monitor
Switch-mode universal power supply
All products fill 2U rack spaces and weigh under 19 pounds
Barrier strip outputs, removable Phoenix-style input
Three-Year, No-Fault, Fully Transferable Warranty completely protects your investment
and guarantees its specifications
The Crown? DSi 1000 power amplifi er shall be a solid-state two-channel model
with a switch-mode universal power supply. A rear-panel HD-15 connector shall
provide input/output connectivity between the DSi amplifi er and the DSi-8M
System Monitor.
The outputs shall be usable as stereo or bridged-mono modes of operation.
The bridged-mono mode shall bridge the outputs to provide increased output
voltage.
Front panel controls and indicators shall include the following:
Level: Detented rotary level control, one per channel.
Power Switch: On/off switch applies AC power to the amplifi er.
Sel/Prev/Next Buttons: Three buttons near the LCD screen shall be used to
access menu items.
LCD Screen: Backlit liquid crystal display shows speaker presets and signal
processing.
Signal Indicator: Green LED, one per channel, fl ashes when a very low-level
signal is present at input.
?10 Indicator: Green LED flashes when output signal exceeds ?10 dB below
clip.
?20 Indicator: Green LED flashes when output signal level exceeds ?20 dB
below clip.
Ready Indicator: Green LED, one per channel, illuminates when the amplifi er is
ready to produce audio.
Clip Indicator: Red LED, one per channel, turns on at the threshold of audible
distortion.
Temp/Fault Indicator: Red LED, one per channel, illuminates under Fault or
excessive temperature conditions.
Power Indicator: Blue LED illuminates when the amplifi er has been turned on
and has power.
Rear panel controls and connectors shall include the following:
AC Line Connector: NEMA 5-15P (15A).
Input Connector: Two 3-pin removable Phoenix-type connectors each accept a
balanced line-level input signal.
Output Connectors: 4-position barrier strip with connectors for dual louspeakers
or bridge-mono loudspeaker.
HiQnet USB Connector: Type B, connects to a HiQnet network.
HD-15 Connector: For cinema I/O compatibility with DSi-8M System Monitor.
The amplifi er shall have the following specifi cations:
Output Power: 2 ohm Stereo (per channel): 700W with 1% THD, 4 ohm Stereo
(per channel): 500W with 0.5% THD, 8 ohm Stereo (per channel) 275W with
0.5% THD, 4 ohm Bridge-Mono: 1,400W with 1% THD, 8 ohm Bridge-Mono:
1,000W with 0.5% THD.
Voltage Gain at 1kHz, 8 ohm rated output: 26 dB.
Frequency Response: +0/?1 dB from 20 Hz to 20 kHz at 1 watt into 4 ohms.
Load Impedance: Safe with all types of loads. Rated for 2 to 8 ohms in Stereo
mode, 4 to 16 ohms in Bridge-Mono mode.
Sensitivity at 8 ohm rated output: 2.35V.
Sensitivity at 4 ohm rated output: 2.24V.
Sensitivity at 2 ohm rated output: 1.88V.
Signal to Noise Ratio (below rated 8-ohm power at 1 kHz): 105 dB
(A weighted).
Damping Factor: Better than 500 from 20 Hz to 500 Hz.
Crosstalk: > 70 dB below rated power, 20 Hz to 1 kHz.
Input Stage: Input is electronically balanced and employs precision 1% resistors.
Input Impedance (nominal): 20 k ohms, balanced;10 k ohms, unbalanced.
Maximum Input Signal: +22 dBu typical.
AC Line Voltage and Frequency Confi gurations Available: 100V, 120V, 220-240V,
50/60 Hz.
AC Line Current: 6.5A.
At Idle: Draws no more than 90 watts.
Operating Temperature: 0° C to 40° C at 95% relative humidity (non-condensing).
The DSP section shall have the following specifi cations:
EQ: 6 parametric fi lters per channel with adjustable Q, boost/cut ±15 dB. Also
adjustable high and low shelving fi lters.
Filters: Highpass and lowpass per channel. Butterworth 12/18 dB per octave
and Linkwitz-Riley 24 dB per octave. High and low shelving fi lters, one per
channel.
Delay: Up to 50 msec total delay per channel.
Output Limiter: Prevents clipping and protects loudspeakers. Choice of ?3, ?6,
or ?12 dB threshold per channel.
Presets: 5 user-defi nable loudspeaker presets and 15 factory-default JBL
system presets.
Protection shall include the following:
DSi-Series amplifi ers shall be protected against shorted, open or mismatched
loads; overloaded power supplies; excessive temperature; chain destruction
phenomena; excessive output current, and input overload damage. They also
protect loudspeakers from input/output DC, large or dangerous DC offsets and
turn-on/turn-off transients
The chassis shall be steel. Cooling shall be by a proportional speed fan with
front-to-rear airfl ow.
Dimensions shall be EIA Standard 19-in. rack mount width (EIA RS-310-B), 3.5
in. (8.9 cm) high and 12.25 in. (31.11 cm) deep behind mounting surface.
Net weight shall be 19 lb (8.6 kg). Shipping weight shall be 22 lb (10.0 kg) |
The high efficiency of the ED series enables maximum efficiency with low heat generation.
A new and unique Class-H circuity technology using state of the art SMD Surface Mount Technology with a reduced number of components offering performance levels exceeding audiophile levels like a slew rate of 50V/µs and high-end extended dynamic sound. The amplifier provides 2x300W into 4 Ohm is equipped complete with temperature-controlled fan cooling, all common protective circuits such as over-temperature, short circuit, RFI and soft start.
The integral soft clip limiter protects against damage to the connected loudspeakers, the activity of a protective circuit, signal and limiter are shown for each channel by LEDʼs.
| AMPLIFIER SPECIFICATIONS |
|---|
| Power output stereo 4Ω: | 2 x 300 Watt rms | | | Power output stereo 8Ω: | 2 x 180 Watt rms | | | Power output bridged 8Ω: | 600 Watt rms | | | Frequency Response: | 20 Hz ÷ 20 kHz | | | Signal/noise rate: | > 105 dB | | | Crosstalk: | > 70 dB | | | Distortion (THD+N): | | | | Intermodulation: | | | | Damping factor: | 200:1 (8 Ω) | | | Slew rate: | 50 V/μS | |
| INPUT SECTION |
|---|
| Input connector: | 2 x XLR balanced, 6,3mm jack unbalanced | | | Input sensitivity: | 0 / 0.775 dBm/V RMS | | | Input impedance: | 10.000 kΩ | | | Controls: | Volume control for each channel | |
| OUTPUT SECTION |
|---|
| Output connector: | 2 x Neutrik Speakon 4 ways | |
| SYSTEM PARAMETERS |
|---|
| Cooling: | Two-speed fan | | | Protections: | Temperature, DC, RFI short circuit, Soft-Start thermal on transformer | | | Amplifier class: | H | |
| POWER REQUIREMENT |
|---|
| Operating voltage: | 220÷240 / 110÷120 ~ 50 / 60 V ~ Hz | | | Max.current: | 6 A | | | Power Consumption: | 1300 W | |
| PHYSICAL SPECIFICATIONS |
|---|
| Height: | 88 / 3.46 mm/inch | | | Width: | 483 / 19.01 mm/inch | | | Depth: | 350 / 13.77 mm/inch | | | Net Weight: | 11.45 / 25.24 Kg/Lbs | |
| SHIPPING INFORMATION |
|---|
| Package height: | 120 / 4.72 mm/inch | | | Package width: | 540 / 21.25 mm/inch | | | Package depth: | 470 / 18.05 mm/inch | | | Shipping Weight: | 13.81 / 30.44 Kg/Lbs |
|
The model L 500 is a 2 x 250 Watts Power Amplifier. Linear Precision Series
power amps combine excellent audio performance, modern and innovative
circuit design, meticulous and exceptionally rigid construction, and the highest
levels of operational integrity and reliability with an appropriate and more than
realistic price. The robust steel chassis provides outstanding torsional strength
through L-shaped side panels reaching under the thick aluminium front panel.
Thermal breakers prevent the power supply units from being damaged by thermal
overload. Electronically controlled fans provide sufficient front-to-rear airflow and
a special cool air diverter takes care of thermal stability. The fans? noise-level is
extremely low which provides the possibility for studio use. If necessary, a supplied
air-filter can be mounted behind the front panel ventilation louvres.
Features
* Excellent audio performance
* Symmetrical topology
* Ultra-low distortion
* Generously dimensioned power supply units
* Suitable to be operated on loads down to 2 ohms
* Suitable to drive complex loads with phase angles of ± 90 degree
* Extensive protection circuitry
* Unique Back-EMF protection
* Switchable limiters
* Switchable Hi/Lo-Cut filters
* Robust steel chassis
* Exceptional low noise front-to-rear air-flow
* XLR-type inputs and direct-outs
* LED display shows On, In, Out, Limit and Protect
* Highly reliable operation
Specs
* Max. Output Power - into 8 ohms : 2 x 180 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 4 ohms : 2 x 280 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 2 ohms : 2 x 320 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 8 ohms bridged : 1 x 560 W at 1 kHz / THD = 1.0%
* Max. Output Power - into 4 ohms bridged : 1 x 640 W at 1 kHz / THD = 1.0%
* Rated Output Power - into 8 ohms : 2 x 175 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 4 ohms : 2 x 250 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 2 ohms : 2 x 300 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 8 ohms bridged : 1 x 500 W at 20 Hz - 20 kHz / THD = 0.1 %
* Rated Output Power - into 4 ohms bridged : 1 x 600 W at 20 Hz - 20 kHz / THD = 0.1 %
* Frequency Response : 0 dB ..... -1 dB/20 Hz - 20 kHz
* Phase Angle Response : ± 30 degree/20 Hz.....20 kHz
* Maximum Output Level : 45 V / RMS before clipping, no load, ref. 1 kHz / THD = 1%
* Voltage Gain ref. 1 kHz : 26 dB (constant gain option)
* Input Sensitivity : 0 dBu/0.775 V, +6 dBu/1.55 V at rated output / 4 ohms ref. 1 kHz
* Maximum Input Level : +21 dBu / 8.7 V
* Input Impedance active balanced : 20 kohms
* THD at Rated Output : < 0.05 % MBW = 80.0 kHz, f = 1 kHz
* IMD -SMPTE : < 0.01 % 60 Hz, 7 kHz, at rated output
* Signal-to-Noise Ratio : >105 dB at rated output into 4 ohms,
A-weighted, RMS, input sensitivity +6 dBu
* Attenuation at rated output : > 70 dB f = 1 kHz
* Damping Factor internal 1 kHz : > 300
* DIM 30 : < 0.01 %
* DIM 100 : < 0.01 %
* Slew Rate internal : > 25 V / ?s
* Power Consumption : 300 W 1/8 rated output into 4 ohms
* Width : 483 mm
* Height : 88.1 mm
* Depth : 426 mm
* Weight : 14 kg
|
Reviews
There are no reviews yet.