Content |
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
Shipping Weight 15 lbs (6.8 kg)
Top
|
Power Output Level 20Hz - 20kHz 1kHz THD+N=0.2%, 8Ω 80W x 4
Power Output Level 20Hz - 20kHz 1kHz THD+N=0.2%, 4Ω 115W x 4
Sensitivity, RL=8. Att.max +4dB
S/N Ratio, 20Hz-20kHz (DIN AUDIO) 100dB
Idle Power Consumption 40W
1/8 Power Consumption (4Ω) 500W
Power Bandwidth, (Half power THD+N=0.5%) 10Hz – 40kHz
Intermodulation Distortion, 60Hz: 7kHz, 4:1, half power 0.1%
Frequency Response, f=20Hz-20kHz -0.5dB, 0dB, 0dB
Residual Noise, 20Hz-20kHz(DIN AUDIO) -70dB
Voltage Gain, 8Ω, f=1kHz 100
Sensitivity, ATT. max 26dB
Maximum Input Voltage 22dB
Input Impedance 30kΩ (balance) 15kΩ (unbalance)
Controls, Front panel POWER switch (push on/push off), attenuator (31position) x 4
Controls, Rear panel MODE switch (STEREO/BRIDGE/PARALLEL) x 2 HPF switch (OFF/20Hz/55Hz 12dB/oct) x 2
Connectors, Output 5–way binding post/ch
Connectors, DATA PORT D-sub15P, Monitor:Output Level/ch,Active/ch, Model Detect Control:Mute/ch
Connectors, Power AC inlet x 1
Indicators, POWER x 1 (Green)
Indicators, SIGNAL x 4(Green)
Indicators, CLIP/LIMIT x 4 (Red)
Indicators, PROTECT/MUTE x 4 (Red)
Load Protection POWER switch on/off mute, DC-fault output relay off
Power Requirements UC: 120V / 60Hz,
Weight 10kg (22 lbs.)
Dimensions (W x H x D) 480 x 88 x 412.2 mm (18-7/8" x 3-7/16" x 16-1/4“)
|
The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment.
In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep.
• Ultra-compact and lightweight 2-U high
• Laser cut aluminum front panels with integrated carrying handles
• Neutrik® XLR input connectors, input and signal link in 2 channel models
• Input Link switch: allow daisy-chaining of the input signal
• Neutrik® Speakon® output connectors
• Detented sealed potentiometers for easy recall of volume settings
• ICL™, PMS™, Hi-temp, Signal indicators per channel
• Power on and Stand-by leds
• Highly versatile with multiple configuration and additional module options
• Full PC control via EtheRAM (with EtheRAM Control module)
• Switchable ICL™ clip-limiters per channel
• Switchable (30-50 Hz) sub-sonic highpass filter per channel
• Three-position gain selector (26, 32 or 38 dB)
• Dual or bridge mode selector
• Twin temperature controlled, back to front cooling fans
• Oversized power components (high SOA reserve specification)
Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility.
Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics:
• 2-way stereo crossover (dual mono or single bridged sub output)
• 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz)
• Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB)
• Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB)
DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics:
• 4 Inputs/4 Outputs or 2 In/2 Out free route configurable.
• 24 bits/192 kHz 256x Oversampling Converters.
• Output Delay: 0 to 7.1 meters (20.69ms) per channel.
• XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel.
• EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB).
• Gain, Mute and Phase inversion per channel.
• RMS Power and Peak Voltage output limiter per channel.
• Real Time operation from USB or front panel configuration.
Standard Signal Inputs Module
EtheRAM Control Module
Ethernet Audio Transport (Coming soon)
Analog Processor Module
DSP44_S Module
EtheRAM Control Module
AES/EBU Digital Input (Coming soon)
|
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
1kHz, 1.0% THD |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
P. N. 12dB C.F. |
|
|
|
|
|
|
|
|
|
|
2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V
3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V
Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB
3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB
Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A
3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A
Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches
Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs
Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ |
The XM series multi-channel power amplifiers are ideal for theater, hall, and conference room installations. The lineup includes 80W × 4 and 180W × 4 models, meeting the needs of a wide variety of installed systems. The XM amplifiers are a compact 2U size and surprisingly lightweight, making them easy to handle and install. Switching power supplies deliver high output power while minimizing the unit's physical size. The XM series has monitor/remote jacks that allow external devices to be connected for status monitoring or control from a remote location.
Dimensions (W x H x D): 480 x 88 x 412 mm, Weight: 10 kg
Four high-power channels. Switchable stereo, parallel, or bridged operation. Versatile connectivity and high-pass filters for a variety of applications. Distribution drive capability for parallel multi-speakers systems (XM4180).
Monitor/Remote connector for remote monitoring and control.
|
Amplifier Gain 32 dB (Lo-Z), 33 dB (70V), 36 dB (100V) Analog Inputs 4, electronically balanced, Phoenix-type Audio Network No CAN Bus Interface Yes (With Optional RCM-810 Card) Continuous Rated Power (1 kHz, THD 1%) 100v 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 2Ω 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 4Ω 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 70v 1000 Watts Continuous Rated Power (1 kHz, THD 1%) 8Ω 500 Watts Continuous Rated Power (20-20 kHz, THD Continuous Rated Power (20-20 kHz, THD Continuous Rated Power (20-20 kHz, THD Continuous Rated Power (20-20 kHz, THD Cooling Front-to-Rear, continuously variable fans DIM 30 0.02 % Electronics Type Amplifier Frequency Response 15 Hz-30 kHz Input Impedance (Balanced) 20 kΩ Input Sensitivity 0 dBu (.775V)-2 Ω, +3 dBu (1.1V)-4/8 Ω, +6 dBu (1.55) 70V/100V Intermodulation Distortion (SMPTE) 0.05 % Mains Voltage 220 - 240 V, 50 - 60 Hz or 120 V, 50 - 60 Hz, 50 - 60 Hz Network Control (IRIS-Net) Optional Total Harmonic Distortion 0.05 % Variable Load Drive (VLD) Yes Height 2RU 88.1 mm (3.47“) Width 483 mm (19.02“) Depth 421.5 mm (16.59“) Weight Net 11.1 kg (24.47 lbs)
| • Eight and four channel models with 300W and 150W per channel • Minimal footprint and mass arround 200mm depth and 6 Kg • Optional Add-on card to interface with third party alarm systems with GPIO connections • FCM™ Faulty Channel Management system to avoid entire device shutdown • State-of-the-art layout for maximum performance and reliability • Highly oversized thermal dissipation design for maximum reliability • Superb distortion and noise figures • All channels bridgeable by pairs • Selectable gain in four channel groups (26, 32 and 38dB) • Subsonic filter per channel (35Hz user selectable) • Temperature and signal dependant, intelligent cooling system for minimal noise • Optimal heat extraction due to the air tunneled enclosure and insulator-less power device attachment to the heatsink • Direct connector-less output for maximum quality loudspeaker control • High grade engineering inside with the latest SMD technology • Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection • Critical electronic and mechanical parts selection • Innovative protection systems, FCM™ Faulty Channel Management and SSP™ SOA Sentry Protection • Detented and optionally tamper-proof volume potentiometers • Hi efficiency, two steps Class H Audio topology • Protection, Signal and Clip indicators per channel • Power On and Standby general indicators • Extremely compact, fully featured QuantaPulse Power supply • Low current consumption and heat generation allowing less demanding conditions for multiple amplifier installations • Factory preset worldwide mains voltage power supply • Laser cut four milimeters aluminium front panel • Rugged 2U steel chasis
|
OUTPUT POWER |
T-604 |
T-1204 |
T-1208 |
T-2408 |
RMS, 1kHz, 1.0% THD+N |
|
|
|
|
4 ohms |
4x 160 W |
4x 320 W |
8x 150 W |
8x 300 W |
8 ohms |
4x 115 W |
4x 220 W |
8x 100 W |
8x 195 W |
Bridge @ 8ohms |
2x 320 W |
2x 640 W |
4x 300 W |
4x 600 W |
Pink Noise 12dB CF |
|
|
|
|
4 ohms |
4x 210 W |
4x 415 W |
8x 180 W |
8x 370 W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™ |
Reviews
There are no reviews yet.