| Content |
Crown CDi Series amplifiers are professional tools designed and built for installed sound applications. The series includes four models which are identical except for output power: CDi 1000, CDi 2000, CDi 4000, and CDi 6000. All are rugged and lightweight, and offer unmatched value in their class.
- Extremely versatile; rated for 2-, 4-, 8-ohm loads and 70V and 140V outputs.
- Switch-mode universal power supply.
- Intuitive front-panel LCD screen for quick, easy configuration.
- Onboard digital signal processing includes crossovers, EQ filters, delay, and output limiting.
- Up to 20 user defined DSP presets are available.
Specifications | Frequency Response (at 1 watt into 4 ohms, 20Hz - 20 kHz) |
+0/–1 dB
| | Signal to Noise Ratio (below rated 8-ohm power at 1 kHz, A-weighted) |
100 dB
| | Damping Factor (8 ohm): 20 Hz to 400 Hz |
> 500
| | Input Stage |
Input is electronically balanced and employs
precision 1% resistors
| | AC Line Current |
CDi 1000: 11.50A, CDi 2000: 11.93A, CDi 4000: 11.75A
At idle: Draws no more than 45 watts.
| | Crosstalk (below rated power) 20 Hz to 1 kHz |
> 70 dB
| | Input Impedance (nominal) |
20 kilohms balanced, 10 kilohms unbalanced
| Load impedance (note: safe with all types of loads)
Dual
Bridge mono |
2–8 ohms
4–16 ohms
| | Voltage Gain (at 1 kHz, 8 ohm rated output) |
CDi 1000: 30.5 dB, CDi 2000: 32.9 dB, CDi 4000: 34.2 dB
| | Sensitivity (at 8 ohm rated output) |
1.4V
| | Maximum Input Signal |
+22 dBu typical
| | Operating Temperature |
0° C to 40° C at 95% relative humidity (non-condensing)
| | AC Line Voltage and Frequency Configurations Available (± 10%) |
100V, 120V-240V, 50/60 Hz
| | Ventilation |
Flow-through ventilation from front to back
| | Cooling |
Heat sinks and proportional-speed fan
| | Dimensions: Width, Height, Depth (behind mounting surface) |
EIA Standard 19 in. Wide (EIA RS-310-B)
x 3.5 in. (8.9 cm) High x 12.25 in. (31.1cm) Deep
CDi 6000 is 16.2 in. (41.15 cm) deep.
| | Net Weight |
CDi 1K, 2K, 4K: 19 lb (8.6 kg).
CDi 6K: 24 lb (10.9 kg).
| | Shipping Weight |
CDi 1K, 2K, 4K: 22 lb (10.0 kg).
CDi 6K: 30 lb (13.6 kg).
| |
RMXa Series: Professional quality performance, incorporating road-proven QSC designs
- Compact size — up to 2500 watts in two rack spaces, or 5000 watts in three rack spaces
- High-current toroidal transformers, for greater 2-ohm power and low noise
- Independent user-defeatable clip limiters reduce distortion
- Selectable low-frequency filters (30 Hz or 50 Hz) protect speakers and increase headroom
- The 4000-watt RMX4050a operates on a standard 15 amp plug (120V)
- Both the RMX4050a and the RMX5050a feature a dual mono, high-current power supply for increased reliability and performance
- The RMX4050a's particularly exceptional combination of cooling capacity and electrical efficiency provides robust thermal performance suitable for high continuous power in 2-ohm stereo or 4-ohm bridged applications.
- Balanced 1/4” (6.3 mm) TRS, XLR, and barrier strip inputs
- Touch-proof binding post and Neutrik Speakon® outputs
- Front mounted gain controls for easy access
- Signal and clip LED indicators for monitoring performance
- Independent DC and thermal overload protection on each channel automatically protects amplifier and speakers
- 3-year warranty plus optional 3-year extended service contract
|
Live performance DSP amplifier. Fully integrated professional speaker processing with FIR Drive technology . Market leading acoustic performance and rock solid reliability. True 2 ohm stability. Intuitive system control software, makes setup and control easy. Rated power: 2 Χ 3000 Watts/2Ω, 2 Χ 2500 Watts/2,6Ω, 2 Χ 1700 Watts/4Ω, 2 Χ 900 Watts/8Ω.
| Manufacturer |
DYNACORD |
| Application |
Portable PA |
| Channels |
Dual Channel |
| Resistance ohms |
8Ω / 4Ω, 2Ω |
| DSP |
Yes |
| Weight (kg) |
18,2 |
| Power (8 ohms/Watt RMS) per channel |
900 |
| Power (4 ohms/Watt RMS) per channel |
1700 |
| Power (2 ohms/Watt RMS) per channel |
3000 |
| Series |
L series |
| Model |
L3600FD |
| Part Number |
F01U312397 |
| Warranty |
3 Years Warranty |
|
| Manufacturer |
POWERSOFT |
| Warranty |
4 Years Gurantee |
| Channels |
Four Channel |
| Resistance ohms |
8Ω / 4Ω / 2Ω |
| DSP |
Yes |
| Power (8 ohms/Watt RMS) per channel |
1600 |
| Power (4 ohms/Watt RMS) per channel |
2000 |
| Power (2 ohms/Watt RMS) per channel |
1800 |
| Weight (kg) |
7.8 |
|
Power supply
- Powersoft legendary universal switch-mode power supply up to 400VAC tolerant with Power Factor Correction
- Patented output filter with ripple cancellation network
- Low Inrush Limiting reduces AC inrush current, removing the need for expensive power sequencers
- Detachable AC mains cable with IEC C19/22.2 (16A for EU, 20 A for USA) socket
Protections
Fully protected circuit design with:
- Ac protection: shut down power supply when AC mains voltage is outside the operating range
- Clip limiter: prevents severely clipped waveforms from reaching loudspeakers, while still maintaining full peak power output
- DC protection: protects against infrasonic signal at the outputs
- VHF protections: protects the loudspeakers against non-audible, strong, non-musical high-frequency signals
- Short circuit protection: protects the amplifier from short circuit or other stressful events for the output circuits with automatic protection reset
- Long term limiter: protects the loudspeaker against steady long term RMS (non-audio) signals, by reducing maximum output
- Thermal protection: output stages operating temperature up to 80 °C (176 °F)
- Temperature controlled continuous variable speed fan, front to back airflow
- Temperature forecast with LCD traced historical behavior
General
- Fixed frequency switchmode output stage for high grade sound accuracy
- Compact size – all models only 1 RU for reduced rack cost and space
- Light weight – for easier racking and shipping: 7 kg (15.4 lbs)
- Standard Phoenix connectors: analog audio outputs, aux supply, alarms and GPIO
- Remotely switchable double input (main and aux) per channel
Loudspeaker system configuration
- Direct drive either low impedance loads or 70V / 100V Hi-Z distributed lines
- Switchable 35Hz / 70Hz high pass filter per channel
- Mixed configuration with Lo-Z/Hi-Z systems possible
- Bridged mode low impedance per channel pair
Alarms and GPI/O
- NC/NO contacts per channel for alarm notifications
- Remote ON/OFF switch
- Remote VCA control per channel
Digital Signal Processing
- TI C6000 DSP platform
- AD/DA converter: dual 24bit @ 48 kHz Tandem® architecture
- Input/output independent equalizers per channel providing PEQ, raised cosine, shelving IIR filters as well as custom output FIR filters
- Delay up to 100 ms for time alignment
- Active DampingControl™ for cable compensation
- Peak, RMS voltage, RMS current, TruePower™ limiters
Remote Control & Monitoring
Via software:
- Control and diagnostics monitoring via ArmoníaPlus
- Dedicated WebApp
Via Hardware:
- Attenuation (from 0dB to 26dB)
- High-pass filters (35Hz, 70Hz)
- Lo-Z/Hi-Z/70V/100V output selection
- Adjustable gain (from 26dB to 35 dB)
| General |
| Output power per Channel |
| Output power per Channel |
1000 W @ 2 Ω |
800 W @ 4 Ω |
800 W @ 8 Ω |
| Bridge mode |
|
2000 W @ 4 Ω |
1600 W @ 8 Ω |
| Max output voltage / current |
| Max unclipped output voltage@8 Ω |
|
|
115 Vpeak |
| Current |
|
|
45 Apeak |
| AC main power |
| Power supply |
Universal, regulated switch mode with PFC (Power Factor Correction) |
| Nominal power requirement |
|
|
100-240 V ±10%, 50-60 Hz |
| Operating voltage |
|
|
90 V – 264 V |
| Power consumption / current draw |
| Idle |
|
115 V: 23 W – 0.34 A |
230 V: 23.3 W – 0.21 A |
| 1/8 of max output power @ 4 Ω |
|
115 V: 267 W – 2.5 A |
230 V: 274 W – 1.5 A |
| THERMAL |
| Operating temperature range |
|
|
0° – 45° C – 32° – 113° F |
| Thermal dissipation* |
| Idle |
|
115 V: 78 BTU/h |
230 V: 79 BTU/h |
| 1/8 of max output power @ 4 Ω |
|
115 V: 229 BTU/h |
230 V: 251 BTU/h |
|
Power Rating
Stereo Mode:
8Ω EIA 1 kHz 1% THD - 1500W
4Ω EIA 1 kHz 1% THD - 2500W
2Ω EIA 1 kHz 1% THD - 4000W
Bridged Mono:
8Ω EIA 1 kHz 1% THD - 5000W
4Ω EIA 1 kHz 1% THD - 8000W
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 5.27V
32dB Setting - 2.67V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 39.1dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -104dB
Total Harmonic Distortion (THD) 0.1% @ 2Ω
0.03-0.06% @ 4Ω
0.01-0.03% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 18A
230V 50Hz - 11A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
|
Reviews
There are no reviews yet.