| Content | Specifications: • Power output: 3,000 watts 2 ohm stereo per ch, 2,100 watts 4 ohm stereo per ch, 1,200 watts 8 ohm stereo per ch, 4,200 watts 8 ohm bridge-mono, 6,000 watts 4 ohms bridge-mono • Sensitivity (for full rated power at 4 ohms): 1.4V RMS • Frequency response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB • S/N Ratio (below rated 1 kHz power at 8 ohms): 103 dB (A weighted) • T.H.D.: 500 • Crosstalk (below rated power): 20 kHz - 1 kHz: >70 dB • Input impedance (nominal): 20k ohms balanced, 10k ohms unbalanced • Maximum input signal: +22 dBu typical • AC Line voltage and frequency configurations: 120 VAC 60 Hz • AC Line current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch): 15.3A; no more than 180 watts at idle • Operating temperature: 0°C to 40°C at 95% relative humidity (non-condensing) • Dimensions: 19" W x 3.5" H x 16.2" D • Net weight: 24 lbs. (13.6 kg). |
Power Output Level R-150 PLUS
STEREO
8ohm(T.H.D 0.05%) 50W+50W
4ohm(T.H.D 0.05%) 75W+75W
BRIDGED MONO
8ohm(T.H.D 0.05%) 50W
8ohm(T.H.D 0.5%) 170W
Frequency Response 20Hz- 20kHz, ±0.5dB
Convection Cooled
SoftStart Protection System
Balanced 10kΩ@0.775V Inputs
|
The new Audio 3-stage CLASS-H SMPS amplifiers incorporate all the features to meet all your needs, whether youʼre starting a P.A. amplifier project from scratch or just need to upgrade your present sound reinforcement equipment. In the amps, youʼll find 2 and 4 channel models, all offering high power levels at low distortion in the range 1.5 to 6 kW, yet weighing around 8.6 kg and only 30 cm deep.
- Model Name: SP6K
- Output Power 1 kHz, 500
- Crosstalk (20 Hz - 20 kHz): > 75 dB
- Voltage Gain (selectable): 26 / 32 / 38 dB
- Input Sensitivity: 5.0 / 2.5 / 1.3 V
- Protection: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, ICL (Inteligent Clip Limiting), PMS (Power Management System), SSP (SOA Sentry Protection)
- Controls: On / Off Switch, Volume, Voltage Gain, Dual / Link Switchable, Bridge Mode Configuration Switch
- Indicators: Signal, Temperature, ICL (Inteligent Clip Limiting), PMS (Power Management System)
- Connectors:
- Input: 2 x XLR
- Line Output: 2 x XLR
- Speaker Output: 2 x Speakon
- Power Supply: 230 V - 50 Hz
- Dimensions (W x H x D): 483 × 88.9 × 310 mm
|
- 2900W RMS x 1 at 2 ohms
- 1780W RMS x 1 at 4 ohms
- 975W RMS x 1 at 8 ohms
- 2525W RMS x 2 at 2 ohms
- 1510W RMS x 2 at 4 ohms
- 890W RMS x 2 at 8 ohms
- 2 channel independent, fourth-order Linkwitz-Riley crossovers
- DDT protection
- Revolutionary IPR class D topology
- Detented input controls
- Combination XLR 1/4 inputs
- 4 pole twist lock output connectors
- Ultra-light weight
- Individual signal pass 1/4" jacks on each channel
- LED illuminated
- Standby, LED power present indication
- Weight Unpacked: 6.2 kg
- Weight Packed: 7.9 kg
- Width Packed: 53.34 cm
- Height Packed: 53.848 cm
- Depth Packed: 15.24 cm
|
The E Series is a range of lightweight, high-power switch mode amplifiers designed to the highest standards of reliability and sound quality. Developed for the touring market, E Series retain the sonic integrity of the benchmark MC and T Series amplifiers, without the physical weight.
The switch mode power supply is capable of delivering high peaks without any perceptible bass 'sag' at very low distortion and is kept within its safe operating area by the new, sophisticated MC² Audio 'intelligent' limiter. The E15, E25, E45 and E4-75 feature MC² Audioʼs proprietary current driven output stages for ultra-high definition sound, delivered over the entire audio bandwidth.
The E90 and the E100 are Class D amplifiers designed to meet the demands for higher power with increased efficiency whilst still maintaining the renowned MC² Audio sonic qualities and unsurpassed reliability.
All MC² Audio products are covered by a 5 year warranty.
Number of Channels: 2
Frequency Response:
20Hz to 20kHz
(+/- 0.3dB)
Output Power: (per channel)
8 ohms 1250W
4 ohms 2500W
2 ohms 4200W
Output Power: (bridged)
8 ohms 5000W
4 ohms 8400W
THD%: (@1dB below max output)
@ 1kHz 20Hz to 20kHz
Gain / Sensitivity:
Gain 26/32/33dB
Sensitivity (for max power) dBu +15.7/9.7/5.7 (4.7/2.4/1.5V)
Power Consumption:
Nominal @ 240v into 4 ohms 4.5A
Nominal @ 120v into 4 ohms 9.0A
Dimensions: (2U) (mm)
Amplifier 88(h) x 482(w) x 428(d)
Single Box (UK shipping) 230 x 580 x 560
Double Box (outside UK) 250 x 610 x 600
Weight:
Amplifier 11.4kg
Boxed (shipping weight) 13.4kg User's Manual
|
Info
Professional Power Amplifier 2X1200W/4Ω - Compact size (2-Rack height) - Stable SMPS (Switch Mode Power Supply) applied for low power consumption and low weight - Voltage gain available - High Damping Factor and low T.H.D - Includes clip limiter to prevent a sound crush - For better efficiency, 2-step of H-class AMP accepted - Includes protection circuit to prevent a damage of over heat, short and over voltage - Has 30Hz or 50Hz HPF to protect speaker from low-frequency - 12 Kg
|
Reviews
There are no reviews yet.