| Content | Specifications: • Power output: 3,000 watts 2 ohm stereo per ch, 2,100 watts 4 ohm stereo per ch, 1,200 watts 8 ohm stereo per ch, 4,200 watts 8 ohm bridge-mono, 6,000 watts 4 ohms bridge-mono • Sensitivity (for full rated power at 4 ohms): 1.4V RMS • Frequency response (at 1 watt, 20 Hz - 20 kHz): +0 dB, –1 dB • S/N Ratio (below rated 1 kHz power at 8 ohms): 103 dB (A weighted) • T.H.D.: 500 • Crosstalk (below rated power): 20 kHz - 1 kHz: >70 dB • Input impedance (nominal): 20k ohms balanced, 10k ohms unbalanced • Maximum input signal: +22 dBu typical • AC Line voltage and frequency configurations: 120 VAC 60 Hz • AC Line current (120 VAC amplifier playing 1/8 power pink noise into 4 ohms per ch): 15.3A; no more than 180 watts at idle • Operating temperature: 0°C to 40°C at 95% relative humidity (non-condensing) • Dimensions: 19" W x 3.5" H x 16.2" D • Net weight: 24 lbs. (13.6 kg). |
Dynacord H 5000
The power amp H5000 is part of Dynacord´s new PowerH SERIES, which marks a milestone in the design and the production of high-performance power amplifiers. The innovative 3-stage Grounded Bridge Class H Topology with "floatingË switching power supply unit offers very high and stable output with extreme high efficiency on an extremely high performance level at minimum weight. PowerH amps are ideal for driving professional touring, high-end Concert-Sound and Pro-Sound applications.
Dynacord H 5000 features:
2x 1500 Watt / 8 Ohm
2x 2500 Watt / 4 Ohm
2x 3500 Watt / 2 Ohm
Cooling: Front-to-Rear, 5-stage-fans
Dimensions (WxHxD): 483 x 88.1 x 498 mm
Weight: 14.5 kg
Protections:
Audio limiters
High temperature
DC
HF
Short Circuit
Back-EMF
Peak current limiters
Inrush current limiters
Turn-on delay
Mains Circuit Breaker Protection
Mains Overvoltage Protection
|
Power Rating
Stereo Mode:
8Ω EIA 1 kHz 1% THD - 1500W
4Ω EIA 1 kHz 1% THD - 2500W
2Ω EIA 1 kHz 1% THD - 4000W
Bridged Mono:
8Ω EIA 1 kHz 1% THD - 5000W
4Ω EIA 1 kHz 1% THD - 8000W
Damping Factor Not Specified By Manufacturer
Input Sensitivity 26dB Setting - 5.27V
32dB Setting - 2.67V
Input Impedance > 10kΩ balanced, or unbalanced
Gain 39.1dB
Frequency Response 20Hz to 20kHz, +/- 0.2dB
Signal-to-Noise Ratio -104dB
Total Harmonic Distortion (THD) 0.1% @ 2Ω
0.03-0.06% @ 4Ω
0.01-0.03% @ 8Ω
Input Connections Input: XLR Male, XLR Female and 3-pin detachable terminal blocks (1 each per channel)
DataPort: HD-15, input signal in parallel with XLR input connectors
Output Connectors Output: Neutrik Speakon (ch 1 wired to both channels) and 5-way binding posts
Controls Front Panel AC Power Switch
Gain Controls, 21 detents, 1 dB steps (each channel)
Controls (Rear) Input Mode: Bridge (Yellow), Stereo (Green), or Parallel (Orange)
Gain / Sensitivity: 26dB (Orange), 32dB (Green), or 1.2V (Yellow)
High Pass (each channel): 3Hz (Off), 30Hz (Yellow), or 50Hz (Orange)
Clip Limiter (each channel): Off, On (Yellow)
Indicators Clip Limiter (each channel): Off, On (Yellow)
Camera Resolution Flow-thru air path and solid aluminum heat sinks
Power Consumption 120V 50/60Hz - 18A
230V 50Hz - 11A
Power Requirements Not Specified By Manufacturer
Dimensions (WxHxD) 19 x 3.5 x 15.63" (48.3 x 8.9 x 39.7cm)
Weight 33.5 lbs (15.2kg)
Specialties Parallel Dataport, XLR/M and XLR/F connectors for simple loop-through connectivity
|
Amplifier Gain 39 dB, 35 dB 32 dB (switchable)
CAN Bus Interface Optional with RCM-26
Continuous Rated Power
(1 kHz, THD 1%) 2Ω 3500 Watts
Continuous Rated Power
(1 kHz, THD 1%) 4Ω 2500 Watts
Continuous Rated Power
(1 kHz, THD 1%) 8Ω 1500 Watts
Continuous Rated Power
(20-20 kHz, THD |
Model T4n
Product Type Power Amplifier
Output Power (W) 1kHz THD+N=1% (120V)
2Ω per channel 2200
4Ω per channel 1950
8Ω per channel 1150
4Ω bridge 4400
8Ω bridge 3900
Output Power (W) 1kHz 20mS burst (120V)
2Ω per channel 2900
4Ω per channel 1950
8Ω per channel 1150
4Ω bridge 5800
8Ω bridge 3900
SN ratio (20Hz-20kHz) 106dB ![t4nrear]( "t4nrear") THD+N 20Hz-20kHz, Half Power RL-4Ω, 8Ω
Intermodulation Distortion 60Hz: 7kHz, 4:1, Half Power 0.1%
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (Max) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (TYP) 0dB
Frequency response RL=8Ω,Po=1W,HPF=OFF 20Hz-20kHz (MIN) 6dB
Channel Separation (Half Power RL=8Ω,1kHz Att. max input 600Ω shunt) 70dB
Residual Noise Att,min 20Hz-20kHz(DIN AUDIO) -70dBu
Damping factorRL=8Ω 1kHz 800
Voltage Gain Att.max 26dB
Maximum Input Voltage +24dBu
Input Impedence 20kΩ (balance) 10kΩ (unbalance)
Controls Specifications
Front Panel POWER switch(push on/push off) attenuator (31 position) x2
Rear Panel MODE switch (STEREO/BRIDGE/PARALLEL) X1; HPF switch (20Hz/OFF 12dB/oct) x1; AMP ID switch (6PDIP)x1
Connectors Specifications
Input XLR-3-31 type/ch; Euroblock connector (balance)/ch
Output SPEAKON/ch, 5way biding postx1
Date Port RJ45x2
Indicators Specifications
Power/Standby x1 (Green/Orange)
Remote x1 (Green)
Protection x1 (Red)
Temp x1 (Red) heatsink temp 85°C
Signal x2 (Green)
Mute x2 (Red)
Clip/Limit x2 (Red)
Load protection POWER switch on/off mute; DC-fault: power supply shutdown / do not return automatically
Cooling Variable-speed fan: x2
Power requirements 120V/60Hz
Weight 14.0 kg
Dimensions (W x H x D) 480 x 88 x 456mm (2U)
|
A full model revision takes Yamaha's high-end PC-N power amplifiers to the next level - the PC-1N
Series. The new PC-1N Series amplifiers feature an extraordinarily solid low end, rich midrange,
and superbly defined highs. They also deliver fast response and exceptional stability even in the face
of serious power supply limitations. Refinements throughout this expanded five-model lineup make
these amplifiers the new benchmarks for quality, reliability, and versatility in professional applications. Frequency Response: 10 Hz – 40 KHz. Ισχύς 2 x 1050 Watt / 8Ω RMS, 2 x 1650 Watt / 4Ω RMS, 3000 Watt / 8Ω bridge RMS. Weight: 13 κιλά.
|
Reviews
There are no reviews yet.