Content |
Model CT475
Product Type Amplifier
Channels 4
Sensitivity 1.4V
Rated Power Output 75W per Channel into 8 ohms
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted 110dB
Total Harmonic Distortion (THD) (full rated power, 20Hz - 20kHz)
Intermodular Distortion (from 0dB down to -40dB)
Frequency Response (at 1W into 4/8 ohms) ± 0.5dB
Crosstalk (below rated power 20Hz to 1kHz) > 70dB
Common Mode Rejection (20Hz to 1kHz) > 55dB, typically > 70dB
Dimension (H x W x D) 1.75" x 19" x 14.25“
Weight 10 lbs (4.5 kg)
| The S Series of RAM Audio amplifiers distils all these features to fulfill all your needs, whether youʼre starting a P.A. amplifier project from scratch, or you need to upgrade your present sound reinforcement equipment. In the S Series amps, you'll find five 2-channel models and five 4-channel models, all offering plentiful power levels at low distortion in the range of 1.5 to 6 kilowatts, yet weighing in around 8 kilos and 30 cm deep. • Ultra-compact and lightweight 2-U high • Laser cut aluminum front panels with integrated carrying handles • Neutrik® XLR input connectors, input and signal link in 2 channel models • Input Link switch: allow daisy-chaining of the input signal • Neutrik® Speakon® output connectors • Detented sealed potentiometers for easy recall of volume settings • ICL™, PMS™, Hi-temp, Signal indicators per channel • Power on and Stand-by leds • Highly versatile with multiple configuration and additional module options • Full PC control via EtheRAM (with EtheRAM Control module) • Switchable ICL™ clip-limiters per channel • Switchable (30-50 Hz) sub-sonic highpass filter per channel • Three-position gain selector (26, 32 or 38 dB) • Dual or bridge mode selector • Twin temperature controlled, back to front cooling fans • Oversized power components (high SOA reserve specification) Standard Signal Inputs Module: The S Series amps are equipped as standard with twin Neutrik® XLR, doubled by two other XLR connectors for linking purposes. In the 4 Channel models an XLR input per channel is provided with the signal linking facility. Analog Processor Module: permits a very easy, user-friendly signal processing to enable the amp to set up a bi-amp system without any other outboard device. These are the Processor's main characteristics: • 2-way stereo crossover (dual mono or single bridged sub output) • 24dB/oct Linkwitz-Riley configurable crossover (90, 100 o 120Hz) • Adjustable attenuation in the High-pass outputs (-3, -6 or -9dB) • Adjustable Limiter, relative to Max. Output (-3, -6 or -9dB) DSP44_S Module: Digital Signal Processor fully programmable through an USB port. These are the Processor's main characteristics: • 4 Inputs/4 Outputs or 2 In/2 Out free route configurable. • 24 bits/192 kHz 256x Oversampling Converters. • Output Delay: 0 to 7.1 meters (20.69ms) per channel. • XOver: Up to 48dB/oct Butterworth, Linkwitz-Riley and Bessel. • EQ: 9 filters per channel (Parametric, Shelving, LP,HP,BP,SB). • Gain, Mute and Phase inversion per channel. • RMS Power and Peak Voltage output limiter per channel. • Real Time operation from USB or front panel configuration. Standard Signal Inputs Module EtheRAM Control Module Ethernet Audio Transport (Coming soon) Analog Processor Module DSP44_S Module EtheRAM Control Module AES/EBU Digital Input (Coming soon)
OUTPUT POWER |
S-1500 |
S-2000 |
S-3000 |
S-4000 |
S-6000 |
S-3004 |
S-4004 |
S-4044 |
S-6004 |
S-6044 |
1kHz, 1.0% THD |
2 ohms |
2x880W |
2x1190W |
2x1570W |
2x1950W |
2x2950W |
4x700W |
4x980W |
- |
4x1440W |
- |
4 ohms |
2x575W |
2x790W |
2x1100W |
2x1380W |
2x2025W |
4x500W |
4x670W |
4x975W |
4x1000W |
4x1480W |
8 ohms |
2x325W |
2x460W |
2x630W |
2x810W |
2x1250W |
4x300W |
4x430W |
4x690W |
4x620W |
4x1015W |
Bridge @ 4ohms |
1760W |
2380W |
3140W |
3900W |
5900W |
2x1400W |
2x1960W |
- |
2x2880W |
- |
Bridge @ 8ohms |
1150W |
1580W |
2200W |
2760W |
4050W |
2x1000W |
2x1340W |
2x1950W |
2x2000W |
2x2960W |
P. N. 12dB C.F. |
2 ohms |
2x975W |
2x1360W |
2x2060W |
2x2460W |
2x4225W |
4x890W |
4x1170W |
- |
4x2080W |
- |
4 ohms |
2x610W |
2x880W |
2x1240W |
2x1600W |
2x2600W |
4x580W |
4x820W |
4x1230W |
4x1280W |
4x2110W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz Phase Response (@1W 20Hz-20kHz): ±15deg Total Harmonic Distortion (20Hz-20kHz): Intermodulation Distortion (SMPTE): Crosstalk (20Hz-20kHz): >75dB Voltage Gain (selectable): 26/32/38 dB Sensitivity: 1500:2.6/1.3/0.6V 2000:3.0/1.5/0.8V 3000:3.6/1.8/0.9V 4000:4.0/2.0/1.0V 6000:5.0/2.5/1.3V 3004:2.6/1.3/0.6V 4004:3.0/1.5/0.8V 4044:3.7/1.9/0.9V 6004:3.5/1.8/0.9V 6044:5.0/2.5/1.3V Signal to noise ratio: 1500:112dB 2000:113dB 3000:115dB 4000:116dB 6000:118dB 3004:112dB 4004:113dB 4044:116dB 6004:116dB 6044:118dB Required AC Mains (@4ohms 1/8 r.p.): 1500:4A 2000:4.8A 3000:6.2A 4000:7.5A 6000:10.5A 3004:6A 4004:7.5A 4044:11A 6004:10.5A 6044:15A Dimensions (WxHxD): 483x88.9x310 mm - 19x3.5x12.2 inches Weight (Net): 1500/2000: 8Kg - 17.6Lbs 3000/4000/3004/4004/4044: 8.5Kg-18.7Lbs 6000/6004/6044: 8.6Kg-18.9Lbs Protections: Soft-start, Turn-on Turn-off transients, Muting at turn-on, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply,ICL™, PMS™, SSP™ |
High-tech in professional amplification!
The fP 2400Q is a lightweight and space-saving four-channel power amplifier, ideal for use in high quality touring sound systems as well as in demanding permanent installations. The fP 2400Q offers a diverse choice of applications, such as: multi-channel monitor systems, four-channel reproduction, and compact amplification in active 2-, 3-, and 4-way systems. The fP 2400Q makes possibile the bridge connection of one or two of the two pairs of channels (channel A and B and/or channel C and D). It also features Lab.gruppen?s unique power matching solution, the MLS switch, which offers endless combinations for solving most of the problems related to varying impedances and maximum power capacities of loudspeakers. The latest semiconductor technology is utilized in the new ferrite Power (fP) amplifiers. This, together with Lab.gruppen?s proprietary copper cooling system, Intercooler?, enhances the 2 ohms capacity. Two easily accessible dust filters on the front ensure a clean front-to-rear airflow. Additionally, a new Bi-phase wiring scheme also increases the capacity of the switch mode power supply. This extends the power bandwidth in the low end.
Key Features: 4 x 370 watts @ 8 ? 4 x 380 watts @ 4 ? 4 x 500 watts @ 2 ? (Measured just below clip level, with all 4 channels driven) Light weight and compact: only 8.6 kg (19lbs), 2U high MLS? Switch: Lab.gruppen?s unique power matching for different loads
New Features: Replaces the LAB 1200C Easily accessible dust filters Improved low-end power bandwidth Extruded front panel for increased stability
Besides the traditionally superb Lab.gruppen sonic performance, there is a full line of features to make the fP family functional in all situations from installation to high performance live sound systems:
Regulated switch mode power supply Today there are many lightweight, switch-mode amplifiers in the market. However, the unique Lab.gruppen switch-mode power supply technology offers a number of essential advantages that make it superior to other and seemingly similar power supply designs. The most important features are the regulated power supply and the extreme power efficiency. The regulated power supply easily deals with a very high variation in the AC mains voltage: it can drop by up to 20% below its nominal level - e.g. to 180 V instead of 230 V ? without any problem. Perhaps even greater benefits result from the extreme efficiency of Lab.gruppen amplifiers: only a fraction of the energy from the AC mains is turned into heat. A regulated power supply also presents some other sonic advantages, such as better cone control and the same fast response as a conventional power supply.
Sophisticated protection circuitry, combining: ALS? short circuit protection; the Adaptive Limiting System permits very high peak currents, but keeps the amplifier within the Safe Operation Area DC protection; protects against infrasonic signals VHF protection; protects the loudspeakers against strong very high frequency non-musical signals above the audible range Thermal protection; prevents the amplifier from being overheated. The protection indicators on the front panel are switched on, as a warning, before the protection process is initiated AC protection; shuts down the power supply if the line voltage is outside the operating voltage Clip limiter; prevents severely clipped waveforms from reaching the loudspeakers, whilst maintaining full peak power. |
• Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal
noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less
power device attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™
SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding
conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis
|
OUTPUT POWER |
T-604 |
T-1204 |
T-1208 |
T-2408 |
RMS, 1kHz, 1.0% THD+N |
|
|
|
|
4 ohms |
4x 160 W |
4x 320 W |
8x 150 W |
8x 300 W |
8 ohms |
4x 115 W |
4x 220 W |
8x 100 W |
8x 195 W |
Bridge @ 8ohms |
2x 320 W |
2x 640 W |
4x 300 W |
4x 600 W |
Pink Noise 12dB CF |
|
|
|
|
4 ohms |
4x 210 W |
4x 415 W |
8x 180 W |
8x 370 W |
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™ |
|
| • Eight and four channel models with 300W and 150W per channel
• Minimal footprint and mass arround 200mm depth and 6 Kg
• Optional Add-on card to interface with third party alarm systems with GPIO connections
• FCM™ Faulty Channel Management system to avoid entire device shutdown
• State-of-the-art layout for maximum performance and reliability
• Highly oversized thermal dissipation design for maximum reliability
• Superb distortion and noise figures
• All channels bridgeable by pairs
• Selectable gain in four channel groups (26, 32 and 38dB)
• Subsonic filter per channel (35Hz user selectable)
• Temperature and signal dependant, intelligent cooling system for minimal
noise
• Optimal heat extraction due to the air tunneled enclosure and insulator-less
power device attachment to the heatsink
• Direct connector-less output for maximum quality loudspeaker control
• High grade engineering inside with the latest SMD technology
• Balanced Inputs with 0.1% tolerance resistors for a precise noise rejection
• Critical electronic and mechanical parts selection
• Innovative protection systems, FCM™ Faulty Channel Management and SSP™
SOA Sentry Protection
• Detented and optionally tamper-proof volume potentiometers
• Hi efficiency, two steps Class H Audio topology
• Protection, Signal and Clip indicators per channel
• Power On and Standby general indicators
• Extremely compact, fully featured QuantaPulse Power supply
• Low current consumption and heat generation allowing less demanding
conditions for multiple amplifier installations
• Factory preset worldwide mains voltage power supply
• Laser cut four milimeters aluminium front panel
• Rugged 2U steel chasis
Frequency Response (power bandwidth ±0.25dB): 20Hz-20kHz
Phase Response (@1W 20Hz-20kHz): ±15deg
Total Harmonic Distortion (20Hz-20kHz):
Intermodulation Distortion (SMPTE):
Crosstalk (20Hz-20kHz): >70dB
Voltage Gain (selectable): 26/32/38 dB
Sensitivity: T604:1.5/0.8/0.4V - T1204:2.1/1.0/0.5V - T1208:1.4/0.7/0.4V - T2408:2.0/1.0/0.5V
Signal to noise ratio: T604:107dB - T1204:110dB - T1208:107dB - T2408:110dB
Required AC Mains (@8ohms 1/8 rated power): T604:1A - T1204:1.5A - T1208:1.4A - T2408:2.6A
Dimensions (WxHxD): 483x88.9x210 mm - 19x3.5x8.27 inches
Weight (Net): T604/T1204: 5.4Kg - 11.8Lbs T1208/T2408: 6.2Kg-13.5Lbs
Protections: Soft-start, Turn-on Turn-off muting, Over-heating, DC, RF, Short-circuit, Open or mismatched loads, Overloaded power supply, SSP™ and FCM™
OUTPUT POWER |
T-604 |
T-1204 |
T-1208 |
T-2408 |
RMS, 1kHz, 1.0% THD+N |
|
|
|
|
4 ohms |
4x 160 W |
4x 320 W |
8x 150 W |
8x 300 W |
8 ohms |
4x 115 W |
4x 220 W |
8x 100 W |
8x 195 W |
Bridge @ 8ohms |
2x 320 W |
2x 640 W |
4x 300 W |
4x 600 W |
Pink Noise 12dB CF |
|
|
|
|
4 ohms |
4x 210 W |
4x 415 W |
8x 180 W |
8x 370 W |
|
The XM series multi-channel power amplifiers are ideal for theater, hall, and conference room installations. The lineup includes 80W × 4 and 180W × 4 models, meeting the needs of a wide variety of installed systems. The XM amplifiers are a compact 2U size and surprisingly lightweight, making them easy to handle and install. Switching power supplies deliver high output power while minimizing the unit's physical size. The XM series has monitor/remote jacks that allow external devices to be connected for status monitoring or control from a remote location.
Dimensions (W x H x D): 480 x 88 x 412 mm, Weight: 10 kg
Four high-power channels. Switchable stereo, parallel, or bridged operation. Versatile connectivity and high-pass filters for a variety of applications. Distribution drive capability for parallel multi-speakers systems (XM4180).
Monitor/Remote connector for remote monitoring and control.
|
Reviews
There are no reviews yet.