Content | Crown XLI 800
The Crown XLI 800 is a reasonably priced but robust and powerful power amplifier. It ideally suits the use in budget-oriented applications at both mobile and stationary areas. It offers a power of 2 x 300 Watts at 4 Ohms. Thereby, the integrated fan guarantees a high operating safety, due to the constant airstream for cooling the power amplifier. The XLI 800 offers a robust an analogue circuit, which is supplied by a conventional power supply. Furthermore it owns three different, selectable modes (stereo, bridge and parallel).
Crown XLI 800:
- Reasonably priced, robust and powerful power amplifier
- Robust and analogue circuit
- LED display for each channel for signal, clip and error
- Stereo, bridge and parallel modes
- Conventional power supply
- Performance: 2 x 200 Watts / 8 Ohms, 2 x 300 Watts / 4 Ohms
- Inputs: Cinch, XLR
- Outputs: 2 x speakon, spring clip
- Robust 19 inch housing
- Height: 2 U
Specifications
|
XLi800 |
XLi1500 |
XLi2500 |
XLi3500 |
Channels |
2 |
2 |
2 |
2 |
Sensitivity (full rated power at 8 ohms) |
0.775V or 1.4V |
0.775V or 1.4V |
0.775V or 1.4V |
0.775V or 1.4V |
Signal to Noise Ratio (below rated power 20Hz to 20kHz, A-Weighted) |
> 100 dB |
> 100 dB |
> 100 dB |
> 100 dB |
Total Harmonic Distortion (THD) (20Hz - 20kHz) |
|
|
|
|
Inter Modulation Distortion (60Hz and 7kHz at 4:1 from full rated output to -40 dB) |
= / |
= / |
= / |
= / |
Frequency Response (at 1W, 20Hz - 20kHz) |
0 dB, -1 dB |
0 dB, -1 dB |
0 dB, -1 dB |
0 dB, -1 dB |
Crosstalk (below rated power) |
at 1kHz: -75 dB |
at 1kHz: -75 dB |
at 1kHz: -75 dB |
at 1kHz: -75 dB |
at 20kHz: - 59 dB |
at 20kHz: - 59 dB |
at 20kHz: - 59 dB |
at 20kHz: - 59 dB |
Damping Factor (from 10Hz to 400Hz, 8 ohms) |
> 200 |
> 200 |
> 200 |
> 200 |
AC Line Voltage and Frequency Configurations (± 10%) |
120VAC 60Hz |
120VAC 60Hz |
120VAC 60Hz |
120VAC 60Hz |
220VAC 50/60Hz |
220VAC 50/60Hz |
220VAC 50/60Hz |
220VAC 50/60Hz |
230-240VAC 50/60Hz |
230-240VAC 50/60Hz |
230-240VAC 50/60Hz |
230-240VAC 50/60Hz |
|
|
|
|
|
Dimensions (H x W x D) |
3.5" x 19" x 12.4“ |
3.5" x 19" x 12.4“ |
3.5" x 19" x 12.4“ |
3.5" x 19" x 14.4“ |
(89 x 482 x 315mm) |
(89 x 482 x 315mm) |
(89 x 482 x 315mm) |
(89 x 482 x 366mm) |
Net Weight |
25.1 lb (11.4 kg) |
28.0 lb (12.7 kg) |
29.7 lb (13.5 kg) |
43.0 lb (19.5 kg) |
Net Shipping Weight |
29.5 lb (13.4 kg) |
32.4 lb (14.7 kg) |
34.2 lb (15.5 kg) |
47.4 lb (21.5 kg) |
|
Power Output Level R-150 PLUS
STEREO
8ohm(T.H.D 0.05%) 50W+50W
4ohm(T.H.D 0.05%) 75W+75W
BRIDGED MONO
8ohm(T.H.D 0.05%) 50W
8ohm(T.H.D 0.5%) 170W
Frequency Response 20Hz- 20kHz, ±0.5dB
Convection Cooled
SoftStart Protection System
Balanced 10kΩ@0.775V Inputs
|
HPS 1500 is a 2 channel power amplifier that delivers up to 2 x 750 W RMS @ 4 Ω (1500 W RMS bridged @ 8 Ω).
XLR inputs for patching in signals as well as Speakon ports for connecting speaker systems are provided for the maximum flexibility.
A forced air cooling system maintains a low operating temperature.
Features |
---|
Fast response and low distortion | Easy to configure in stereo / mono / bridge modes | Extensive protective circuits ensure high reliability and operating safety | Front panel signal / clip / protect LED indicators | Minimum load impedance (stereo / mono): 4 Ohm | XLR input connectors | SPEAKON output connectors | Switchable limiter |
2 unit 19" rack, low weight for easy transportation
AMPLIFIER SPECIFICATIONS |
---|
Power output stereo 4Ω: | 2 x 750 Watt rms | | Power output stereo 8Ω: | 2 x 450 Watt rms | | Power output bridged 8Ω: | 1500 Watt rms | | Frequency Response: | 20 Hz ÷ 20 kHz | | Signal/noise rate: | 106 dB | | Damping factor: | > 300 | | Slew rate: | 50 V/μS | |
INPUT SECTION |
---|
Input connector: | xlr | | Input sensitivity: | 1.4 V (/ 32 – 26 dB) dBm/V RMS | | Input impedance: | 20 kΩ (balanced), 10 kΩ (unbalanced) kΩ | |
OUTPUT SECTION |
---|
Output connector: | Speakon | |
SYSTEM PARAMETERS |
---|
Cooling: | Forced | | Amplifier class: | H | |
POWER REQUIREMENT |
---|
Operating voltage: | 220 ÷ 240 V (50 / 60 Hz) V ~ Hz | |
PHYSICAL SPECIFICATIONS |
---|
Height: | 88/3.4 mm/inch | | Width: | 482/18.9 mm/inch | | Depth: | 420/16.5 mm/inch | | Net Weight: | 17/37.4 Kg/Lbs |
|
|
XB Series - Intelligent Power
Power Without Compromises. The XB is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection- the XB is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX / Speakon LED Indicators for POWER, SIGNAL, CLIP, PROTECT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XB 800: 2x 400 W @ 4 Ohm Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.025% Signal-to-Noise Ratio: < 103 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: 500 @ 4 Ohm Cooling: 2x fan (temp. reg. variable speed) Weight: 13 kg/(29 lbs) Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“)
|
Reference Quality Power Amplifier [R-300 Plus] - Controls :
Front : Power on/off switch, attenuator, LED indicator
Rear : Mode seletor switch, Stereo/bridged mono switch - Connectors :
Input : 1 XLR, 1/4" balanced per channel
Output : 5-way binding post and SpeakonTM per channel - Indicators :
Power : Green, Protection : Red, Clip : Red, Signal : Green - Power Source : 100-120VAC or 220-240VAC; 50/60Hz
(supplied AC mains transformer depends on country requirements) - Power Consumption : 250W(2.4A)
- Weight : 8.4kg/18.5lb
- Dimensions (WxHxD) : 482x88x317mm/19x3.5x12.5in
|
XB Series - Intelligent Power
Power Without Compromises. The XB is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection- the XB is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX / Speakon LED Indicators for POWER, SIGNAL, CLIP, PROTECT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XB 400: 2x 200 W @ 4 Ohm Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.025% Signal-to-Noise Ratio: < 103 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: 500 @ 4 Ohm Cooling: 2x fan (temp. reg. variable speed) Weight:12 kg /(26 lbs) Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
Reviews
There are no reviews yet.