Content |
Low weight switching final power amplifier. Power 2X3500W / 4Ω, 2Χ4700W / 2Ω. 7000W bridged 8Ω. New integrated BSS OMNIDRIVE 4bit / 192kHz processor with Cirus Logic SHARC A / D and D / A Converters. LevelMAX peak voltage and RMS compressing, limiting, New hi-end FIR and IIR filters, 2sec delay / channel, as well as DSP presets for various speakers. LCD display on the front panel. USB input on the front panel for loading firmware and Speakers Tunning presets. Analog inputs with XLR, digital input AES / EBU, ethernet input RJ-45 with TCP / IQ protocol. Advanced 3rd generation power supply that allows the amplifier to operate at any voltage. Cooling circuit with microprocessor control with adjustable speed depending on the temperature. Analog and digital outputs (THRU) XLR. Exits speakon 5-way binding post, ground lift switch. Made of cast aluminum, height 2U rack. Suitable for P.A applications but also permanent installations. Weight 10.5kg |
XB Series - Intelligent Power
Power Without Compromises. The XB is designed for paging, music and alarm signals. Versatile, dynamic and extremely rugged according to IEC286-3. For the highest requirements in safety and quality. Sequential power on, alive contacts and incorporated ground fault detection- the XB is the solution under all conditions. Without the need for additional equipment. For uninterrupted and troublefree operation.
High Tech SMT Design Protection Circuits: DC, LF, HF, Thermal, Short Circuit, Current Limiter, 3 ms Muting Delay PHOENIX / Speakon LED Indicators for POWER, SIGNAL, CLIP, PROTECT Temperature controlled, variable speed low noise fans Volume Controls at the back Stereo / Bridged / Parallel Mode Softstart Sequential Remote Power On Alive Contact Ground Lift 3 Years Warranty
TECHNICAL DATA: XB 400: 2x 200 W @ 4 Ohm Class: AB Frequency Response: 20 Hz - 20 kHz (0 / -0.3 dB) THD: < 0.025% Signal-to-Noise Ratio: < 103 dB Channel Seperation: > 85 dB Input Sensitivity: +6 dBu Input Clipping: 22 dBu Input Impedance: 20 kOhm Damping Factor: 500 @ 4 Ohm Cooling: 2x fan (temp. reg. variable speed) Weight:12 kg /(26 lbs) Dimensions: 2 RU / 483 x 88 x 382 mm (19" x 3.5" x 15“) |
The Crown® Macro-Tech® i Series continues the Macro-Tech legacy of unparalleled sonic accuracy and detail, putting sound quality above all else
Patented, cutting-edge Class-I circuitry gets more power out of an amplifier with less waste
Rugged construction ensures that all Macro-Techs are built to withstand years of abuse on the road
Global Power Supply — designed to deliver maximum power no matter what country you work in
Built-in load, line voltage, input and output monitoring
Standard Ethernet networking via System Architect® lets system operators monitor and control the amplifier from any location
Performance
Frequency Response (at 1 watt, 20Hz - 20 kHz into 8 ohms) ± 0.25 dB
Signal to Noise Ratio below rated full-bandwidth power,
A-weighted > 108 dB
Total Harmonic Distortion (THD) at 1 watt into 8 ohms
Total Harmonic Distortion (THD) Plus Noise at full rated power
Intermodulation Distortion (IMD) 60 Hz and 7 kHz at 4:1, from full rated output to –30 dB
Damping Factor (20 Hz to 100 Hz at 8 ohms) > 5000
Crosstalk (below rated power, 20 Hz to 1 kHz) > 80 dB
Common Mode Rejection (CMR) (20 Hz to 1 kHz) > 55 dB, typically > 70 dB
DC Output Offset (Shorted input)
Input Impedance (nominal) 10 kilohms balanced, 5 kilohms unbalanced
Maximum Input Level +20 dBu typical
Load Impedance (Note: Safe with all types of loads)
Stereo: 1/2/4/8/16 ohms Bridge Mono: 2/4/8 ohms
Input Sensitivity (referenced to 8 ohm rated output) 1.4V, 32 dB gain, and 26 dB gain
Voltage Gain (referenced to 8 ohm rated output) MAi-5000i:
37.1 dB to 22.2 dB MAi-9000i:
37.9 dB to 23.0 dB MAi-12000i:
39.3 dB to 24.5 dB
Required AC Mains Universal AC input, 100-240VAC , 50/60 Hz (±15%). Maximum AC mains voltage 264VAC.
AC Line Connector Five cordsets supplied with amplifier (USA, UK, European, Australia, India)
Construction
Cooling Dual-zone, microprocessor controlled, continuously variable speed fans,
front-to-back airflow
Front Panel Cast aluminum with integrated handles.
Weight 28 pounds (12.7 kg) net, 36 pounds (16.3 kg) shipping.
Dimensions (W x H x D) 19 in. (48.3 cm) W x 3.5 in. (8.9 cm) H x 16.2 in. (41.1 cm) D.
Protection Amplifier is protected against reactive loads, faults and shorts. If one channel experiences a catastrophic failure, the entire amplifier will shut down.
4-ohm Dual (per ch): 4,000W
8-ohm Dual (per ch): 2,100W
4-ohm Bridge: 7,000W
8-ohm Bridge: 8,000W
|
Manufacturer |
LAB GRUPPEN |
Warranty |
10 Years Gurantee |
Channels |
Dual Channel |
Resistance ohms |
4Ω / 16Ω |
Resistance ohms |
2Ω |
Power (8 ohms/Watt RMS) per channel |
1450 |
Power (4 ohms/Watt RMS) per channel |
2800 |
Power (2 ohms/Watt RMS) per channel |
3500 |
Weight (kg) |
12 |
|
Manufacturer |
LAB GRUPPEN |
Warranty |
10 Years Gurantee |
Channels |
Dual Channel |
Resistance ohms |
4Ω / 16Ω |
Resistance ohms |
2Ω |
Power (8 ohms/Watt RMS) per channel |
1450 |
Power (4 ohms/Watt RMS) per channel |
2800 |
Power (2 ohms/Watt RMS) per channel |
3500 |
Weight (kg) |
12 |
| L1400 450W-450W 4ohm (280W-280W8ohm)
COMPACT MODERN DESIGN
Compact size (2U-Rack Height) with up to 1200W per channel@2ohms
these amps save valuable rack space without compromising power output.
HIGH CURRENT TOROIDAL TRANSFORMER
A high-current toroidal transformer saves rack space
and minimizes hum and noise.
EXCELLENT SOUND QUALITY
The low T.H.D.(0.05%) and high damping factor (400 or higher)
gives excellent sound quality.
2 STAGE POWER SUPPLY
The high-power units (L1800 and L2400) have a 2-Stage Class-H design
that maximizes their performance.
EQUIPPED WITH 30Hz or 50Hz HPF
All amplifiers are equipped with high-pass filters on each channel to
help maintain sound quality, yet help protect the loudspeakers.
EXTENSIVE PROTECTION CIRCUITS
Extensive protection circuits monitor over voltage/current conditions, overheating,
output shorts, and DC voltage to improve performance and reliability.
CLIP-LIMITER CIRCUITS
Clip-limiters on each channel are provided to help prevent
distortion due to excessive signal levels.
L.E.D FUNCTION DISPLAYS
Power, Clip limiter, Signal, Protection, Mode (Parallel/Stereo/Bridged)
LEDs on the front panel indicate the status of the unit in operation. |
Reviews
There are no reviews yet.