Content |
The DNRP-WRC provides two button record control and visual status indication of a connected Denon® DN-F450R/F650R recorder.
The mouse sized unit, once connecte to the recorder using its integral 5 metre lead, can be placed in a convenient location on a board/ meeting room table to allow the recording of conferences and discussions. Visual indication of recorder status is provided by high brightness red and green indicators located around the RECORD button, which show STOP, PLAY, PLAY PAUSE, PLAY F.FWD, PLAY F.REV, CARD ERROR, RECORD and RECORD PAUSE. The two button control allows the recorder to be placed into record mode, create a new record mark and stop the recording process.
The DNRP-WRC is primarily for the simple control of audio recording in areas where conversations, discussions or conferences are taking place. The unit allows the DNF450R/F650R recorder to be placed out of sight to prevent media tampering or access to all the recorder controls.
- Simple unobtrusive controller for the recording of audio in board/meeting rooms
- Easy connection to Denon DN-F450R/F650R recorder serial (RS232) port
- Provides bright visual indication of STOP, PLAY, PLAY PAUSE, PLAY F.FWD, PLAY F.REV, CARD ERROR, RECORD and RECORD PAUSE
- RECORD and STOP buttons allow simple control without the need to access the recorder
- Ergonomic visually pleasing design with internal weight to prevent table slip
- Ultra low power consumption, no need for additional power adaptor
- Fully sealed label provides protection against drink spills
|
The D-2012C is a 6U rack mountable Remote Console Unit designed for exclusive use with the D-2008SP Digital Mixing Processor Unit. Assigned to any desired channels inside the D-2008SP by the dedicated software, the D-2012C's 12 motorized faders and 8 rotary encoders can remotely adjust their volumes. Desired preset memories can be recalled using 8 function keys. It is equipped with 1 channel line input (stereo), which allows the audio signal to be transmitted to the D-2008SP via monitor bus. Audio signals inside the D-2008SP can be monitored via monitor bus through headphones connected to a stereo headphone output. The D-2012C can be installed on a desk with the additional use of an optional D-2012AS Console Case.
* 0 dB = 0.775 V Power Source | 220 - 240 V AC | Power Consumption | 18 W | Volume Adjustment | 100 mm motorized fader x 12
Rotary encoder x 8 | Line Input | 1 channel (stereo) | Headphone Output | Stereo 100 mW + 100 mW (32 Ω load) | Monitor Bus | 1 stereo input
Connector: RJ45 connector
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable (2 pairs of data lines)
Maximum cable distance: 100 m (109.36 yd) (between D-2012C and D-2008SP) | LAN | Network I/F: 10BASE-T/100BASE-TX (Automatic-Negotiation)
RJ45 connector
Network protocol: TCP/IP
Connection cable: Shielded twisted pair (STP) Cat 5 or higher LAN cable
Maximum cable distance: 100 m (109.36 yd) (between D-2008SP and switching hub) | Control | RS-232C: D-sub connector (9 pins) for maintenance use | Finish | Panel: Surface-treated steel plate
Rack mounting bracket: Surface-treated steel plate | Dimensions | 482 (W) × 266 (H) × 138 (D) mm (18.98 × 10.47" × 5.43) | Weight | 6.6 kg (14.55 lb) | Accessory | Power cord (2 m (6.5 ft)) ……1
Fader knob (yellow) ……3 | Option | Console case: D-2012AS |
|
The APH-2n optional accessory pack includes seven tools for use with the H2n. The remote control can be used to start, stop and pause recordings as well as to add marks. The other accessories in the pack are a windscreen that reduces wind and breath noise, a mic clip adapter for use with a mic stand, a tabletop tripod with extendable legs, a padded-shell case, an AC adapter and a USB cable. |
Stereo Rack Memory Recorder
The UR-2 is a 1 U rack size stereo audio recorder using SD card and USB storage device that is flexibly adapting to the wide variety of playback requirements.
The UR-2 is a new generation stereo memory recorder from Fostex that uses 2 SD cards (SDHC compatible) and USB storage device as the recording media. The recording/ playback file format is BWF (WAV). Its ample playback functions will adapt to the wide variety of playback requirements. It offers high quality recording of up to 24bit/96kHz (in BWF format). Employing FAT 32 disc format, it is easy to process the file transfer to a PC based DAW.
The analog input and output are balanced XLR/+4dBu and un-balanced RCA/-10dBV, the digital input and output complies to AES/EBU and S/P DIF digital signal. It is flexible to be used in the available audio system. The playback function includes Chain Play and Timer Play, it is suitable for live stage performance and sound installation. In addition to the external control via parallel remote with D-Sub 25pin and RS-232C serial remote, a USB keyboard and 10-key keyboard can trigger the instant playback start, which is very useful at a live event, theater and broadcast environments.
The Mic input located on the front panel offers 48V phantom power, it can be used not only for recording but also for speech to be mixed with playback source. Last but not least, its newly employed organic EL display gives an extremely clear visibility. This combined with DC power operation, it serves for outdoor use very well.
MAIN FEATURES
• 2 sets SD card slots and a USB host connector for alternate recording/playback among the different media.
• Stereo or Mono WAV (BWF) recording to SD card (also SDHC) and USB storage device
• Fs: 44.1/48/88.2/96kHz, Quantization: 16/24bit
• High speed file transfer with PC via USB 2.0 (bi-directional)
• Employing FAT32 format, it allows to directly mount the recorded files to PC.
• It adapts to a wide variety of use environment by offering Chain Play and Memory Play.
• Timer Play and Power ON Play enable automatic playback start for such as chime and repetitive announcement, which are convenient in the installation audio industry.
• The play mode list employs CSV file format so that it is easy to edit by a text editor or spread sheet program software on PC.
• 99 Cue points with locate function. Waveform display under Scrub mode offers easy and visual Cue point setting
• Microphone input with P48V available on the front panel. Not only for recording but for speech to be mixed with playback source.
• Analog I/O with balanced XLR and un-balanced RCA pin jacks, Digital I/O with XLR connectors
• An organic EL display offers high visibility.
• Remote transport control via Foot SW, Parallel remote pot (Dsub 25pin) and RS-232C (D-sub 9pin)
• External USB keyboard can be used not only for file name editing but for transport control such as REC and PLAY.
|
Specifications
General
Recording media CompactFlash card
Tested media SanDisk Extreme IV 4 GB, 8 GB, 16 GB
SanDisk Extreme 4 GB, 8 GB, 16 GB
File system FAT32
File format BWF (single-channel, multi-channel)
Number of audio channels 8 channels at 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz
8 channels + stereo mix at 44.1 kHZ, 48 kHz
4 channels at 176.4 kHz, 192 kHz
Quantization bit rates 16 bit/24 bit
Sampling frequencies 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1% pull-up/pull-down)
Reference clock Internal, Word in, Video in,
Digital in (CH 1-2, CH 3-4, CH 5-6, CH 7-8)
Timecode frame rates 23.976, 24, 25, 29.97 DF, 29.97 NDF, 30 DF, 30 NDF
Built-in mic Omni directional, monaural
Low cut filter Cut-off frequency: 40/80/120 Hz
Slope: –12/–18 dB/oct
Analogue audio inputs and outputs
MIC IN/LINE IN connectors (1–8) XLR-3-31 (1: GND, 2: HOT, 3: COLD)
Input impedance (LINE) 10 kOhm
Nominal input level (LINE) + 6 dBu (Ref. level: –9 dB)
+ 4 dBu (Ref. level: Other than –9 dB)
Maximum input level (LINE) Selectable: +15 dBu, +18 dBu, +20 dBu, + 22 dBu, +24 dBu
Input impedance (MIC –25) 2.4 kOhm
Minimum input level (MIC –25) –45 dBu
Maximum iput level (MIC –25) +11 dBu
Input impedance (MIC 0) 2.4 kOhm
Minimum input level (MIC 0) –70 dBu
Maximum input level (MIC 0) –14 dBu
LINE OUT connectors (L/R) XLR-3-32 (1: GND, 2: HOT, 3: COLD)
Output impedance 100 Ohm or less
Nominal output level +6 dBu (Ref. level: –9 dB)
Nominal output level +4 dBu (Ref. level: Other than –9 dB)
Maximum output level Selectable: +15 dBu, +18 dBu, +20 dBu, +22 dBu, +24 dBu
PHONES connector 6.3-mm stereo phone jack
Maximum output power 100 mW + 100 mW or more (THD+N: 1 % or less, at 32 Ohm)
Digital audio inputs and outputs
DIGITAL I/O connector D-Sub, 25-pin connector
Format AES3-2003/IEC60958-4 (AES/EBU)
Minimum input voltage 200 mVpp
Maximum input voltage 7 Vpp
Output voltage 3.5 Vpp
DIGITAL OUT connectors BNC
Format AES3-2003/AES-3id-2001 (AES/EBU)
Output voltage 1 Vpp at 75 Ohm
Control inputs and outputs
EXT DC IN connector XLR-4-32 (1: –, 2: NC, 3: NC, 4: +)
Input voltage 11–16 V (2 A)
CASCADE/WORD/VIDEO IN connector BNC
Input voltage 5 V TTL equivalent
Input impedance 75 Ohm ±10 %
Allowable frequency deviation of external sync ±100 ppm
CASCADE/WORD OUT connector BNC
Output voltage 5 V TTL equivalent
Output impedance 75 Ohm ±10 %
Sampling frequencies 44.1/47.952/48/48.048/88.2/96/176.4/192 kHz
(47.952/48.048: 48 kHz ± 0.1 % pull-up/pull-down)
TIME CODE IN connector BNC
Input voltage 0.5–5 Vpp
Input impedance 10 kOhm
TIME CODE OUT connector BNC
Output voltage 2.0 Vpp
Output impedance 600 Ohm
USB port USB B-type, 4-pin
Format USB2.0 HIGH SPEED (480 MBit/s)
KEYBOARD connector Mini-DIN connector (PS/2)
Audio performance
Frequency response (MIC/LINE IN to LINE OUT)
All sample rates 20 Hz – 20 kHz, 0 dB (±0.5 dB)
88.2/96 kHz sample rates at 40 kHz –1 dB (±1.0 dB)
176.4/192 kHz sample rates at 80 kHz –3 dB (+1/–2 dB)
Distortion
LINE IN to LINE OUT 0.003 % or less (–20 dB reference level, +23 dBu input, 1 kHz, AES-17 LPF)
MIC IN (MIC –25) to LINE OUT 0.02 % or less (–20 dB reference level, –10 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
MIC IN (MIC 0) to LINE OUT 0.02 % or less (–20 dB reference level, –35 dBu input, Trim at +20 dB, 1 kHz, AES-17 LPF)
S/N ratio
LINE IN to LINE OUT 110 dB(A) or more (22 kHz LPF)
MIC IN (MIC –25 or MIC 0) to LINE OUT 100 dB(A) or more (22 kHz LPF)
Computer compatibility
Windows Windows XP, Windows Vista, Windows 7
CPU Pentium 300 MHz or faster
Memory 128 MB or more
USB USB 2.0 port
Macintosh Macintosh Mac OS X 10.2 or later
CPU Power PC G3, G4, Intel Mac 266 MHz or faster
Memory 64 MB or more
USB USB 2.0 port
Recommended USB host controller Intel chipset
Power supply and other specifications
Power requirements 100–240 V AC, 50–60 Hz (AC adaptor PS-1225L)
10 AA batteries (Alkaline or NiMH)
External DC battery (DC 11–16 V, 2 A or more)
Battery operation time (continuous operation) Measured according to JEITA standard at 48 kHz, 24-bit, 8 ch playback or recording, phantom power off. Varies with operating conditions.
NP type battery (Li-Ion: 14.8 V/4.6 Ah) About 5 hours
AA type batteries (NiMH) About 2 hours
Power consumption 18 W
Dimensions (W x H x D) 270 mm x 100 mm x 260 mm (excluding protrusions)
Weight 3.65 kg (excluding batteries)
Operating temperature range 0–40 ºC
|
UR-80: 24 Bit/96 kHz USB Recording System
Features
- Over forty assignable controls
- Up to 24-bit/96KHz recording
- 2x XLR/TRS combo jack with qualified microphone preamp & phantom power
- Included HQ-GM2, HyperCanvas software synthesizer
- ASIO2.0/WDM, MacOS X compatible drivers, low-latency support.
- UR-80 Editor Software Included
- V-Link support
Knob8Fader9Rotary Encoder1Button25LED10Number of Memory SetsPreset1User7Number of Audio Record/Playback Channels (Full duplex (except for 96 kHz setting))Record2 channels (stereo)Playback2 channels (stereo)Signal ProcessingAD/DA Conversion24 bits (linear)PC interface24 bitsSampling Frequency24 bitsDigital output44.1/48/96 kHzDigital input32/44.1/48/96 kHz* Built-in realtime sample rate converterAD/DA Conversion44.1/48/96 kHzFrequency Response96.0 kHz20 Hz to 40 kHz (+0 dB/-2 dB)48.0 kHz20 Hz to 22 kHz (+0 dB/-2 dB)44.1 kHz20 Hz to 20 kHz (+0 dB/-2 dB)Nominal Input Level (variable)Input Jack 1, 2 (XLR type)-50 to -10 dBuInput Jack 1, 2 (1/4 inch TRS phone type)-35 to +4 dBuInput ImpedanceInput Jack 1, 2 (XLR type)5 k ohmsInput Jack 1, 2 (1/4 inch TRS phone type, Lo-Z)32 k ohmsInput Jack 2 (Hi-Z)1 M ohmsNominal Output LevelOutput Jack0 dBuOutput ImpedanceOutput Jack1 k ohmsHeadphones160 ohmsResidual Noise LevelOutput Jack-90 dBu or less
(input terminated with 1 k ohms, OUTPUT VOLUME: max., INPUT SENS = min., INPUT MONITOR = min., IHF-A, typ.)InterfaceUSB
Digital input/output Coaxial type
Optical type(conforms to S/P DIF)ConnectorsInput Jack 1, 2 (XLR type (phantom power)
1/4 inch TRS phone type)
Digital In Connectors (Coaxial type, Optical type)
Digital Out Connectors (Coaxial type, Optical type)
Headphones Jack (Stereo 1/4 inch phone type)
Output Jack L/R (RCA phone type)OthersPower SupplyAC adaptorCurrent Draw1000 mAAccessoriesInstallation Guide
Owner's Manual
USB cable
AC adaptor
CD-ROM
Overlay Sheets with Application LabelsSize and WeightWidth379 mm14-15/16 inchesDepth239 mm9-7/16 inchesHeight84 mm3-5/16 inchesWeight1.7 kg3 lbs. 11 oz.
|
Reviews
There are no reviews yet.